Related Manuals for Askey EAO2001S
Summary of Contents for Askey EAO2001S
- Page 1 Quick Installation Guide EAO2001S(RoHS) Enterprise Access Point Quick Installation Guide EAO2001S(RoHS) Enterprise Access Point (Outdoor) Copyright © Askey, INC. All rights reserved.
-
Page 2: Copyright Notice
Askey, INC. You may not alter or remove any copyright or other notice from copies of the content. -
Page 3: Fcc Caution
FCC Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 21cm between the radiator & your body. Copyright © Askey, INC. All rights reserved. - Page 4 Quick Installation Guide EAO2001S(RoHS) Enterprise Access Point Taiwan NCC Statement 以下警語適用台灣地區 (1) 經型式認證合格之低功率射頻電機，非經許可，公司、商號或使用者均不得擅自變更頻率、 加大功率或變更原設計之特性及功能。 (2) 低功率射頻電機之使用不得影響飛航安全及干擾合法通信；經發現有干擾現象時，應立即停 用，並改善至無干擾時方得繼續使用。前項合法通信，指依電信法規定作業之無線電通信。 低功率射頻電機須忍受合法通信或工業、科學及醫療用電波輻射性電機設備之干擾。 無線資訊傳輸設備必須具備安全功能，以保護未經授權之一方任意更改軟體進而避免發射機 操作於非經認證之頻率、輸出功率、調變形式或其他射頻參數設定。 無線資訊傳輸設備避免影響附近雷達系統之操作。 無線資訊傳輸設備高增益指向性天線只得應用於固定式點對點系統。 (6) 本器材須經專業工程人員安裝及設定，始得設置使用，且不得直接販售給一般消費者。 (7) MPE 標準值及送測產品實測值:電磁波暴露量 MPE 標準值 1mW/cm2，送測產品實測值為： 0.57194 mW/cm2，本產品使用時建議應距離人體 21cm。 Copyright © Askey, INC. All rights reserved.
- Page 5 EAO2001S(RoHS) Enterprise Access Point Introduction EAO2001S(RoHS) can be installed by wall-mounted installation kit in any occasion, EAO2001S(RoHS) provide IP67 waterproof, dustproof metal cabinet design, can be against Taiwan's outdoor environment and climate conditions, even if long-term outdoors, high and low temperature environment can operate EAO2001S(RoHS) Copyright ©...
- Page 6 5 seconds. Offers uplink connection. This port can be used to connect to a controller, gateway, or directly to the Internet. 802.3at PoE is (Uplink (PoE) Port) also supported Copyright © Askey, INC. All rights reserved.
- Page 7 Quick Installation Guide EAO2001S(RoHS) Enterprise Access Point Connecting Askey EAO2001S(RoHS) to Internet Access device 1. Connect the Ethernet to PoE injector. 2. Plug PoE Injector on. 3. Make sure the RUN/ALARM LED is on. Copyright © Askey, INC. All rights reserved.
- Page 8 1. Plug in RJ45 cable from your PC to the PoE Injector Ethernet port. 2. From PC and start browser, e.g. Microsoft Edge. 3. Open Microsoft Edge and fill in IP address e.g. “http://192.168.1.1” in the URL. This default EAO2001S(RoHS) IP address is 192.168.1.1 Copyright © Askey, INC. All rights reserved.
- Page 9 Quick Installation Guide EAO2001S(RoHS) Enterprise Access Point 4. Pop up authorization required username and password. Default username is “admin” and password is “admin”, then click “login” button. 5. Enter EAO2001S(RoHS) system overview status page. Copyright © Askey, INC. All rights reserved.
- Page 10 Quick Installation Guide EAO2001S(RoHS) Enterprise Access Point 6. Change Wireless settings, please click wireless item then select general page. Copyright © Askey, INC. All rights reserved.
- Page 11 Quick Installation Guide EAO2001S(RoHS) Enterprise Access Point 7. Home > Wireless > General Settings > Setup wireless mode, channel bandwidth and wireless channel. 8. Home > Wireless > VAP Configuration > Change Wireless SSID. Copyright © Askey, INC. All rights reserved.
- Page 12 The relevant regulations are generally specified in the electrical code. Check the installation instructions to check their compliance. Copyright © Askey, INC. All rights reserved.
- Page 13 It is strongly recommended to make a backup copy of your configuration settings. This device is only allowed for outdoor use purpose. For further configuration and backup information, please refer to the User’s Manual. Copyright © Askey, INC. All rights reserved.
Need help?
Do you have a question about the EAO2001S and is the answer not in the manual?
Questions and answers