Advertisement
■
The use of hearing protection may restrict the operator's ability to hear
warning sounds. Pay particular attention to potential hazards around and
inside the working area.
■
Wear heavy, long trousers, boots, and gloves. Do not wear loose-fitting
clothing, short trousers, or jewellery of any kind, and do not use the
product with bare feet.
■
Secure long hair so that it is above shoulder level to prevent entanglement
in moving parts.
■
Before use and after any impact, check that there are no damaged parts
on the product. A defective switch or any part that is damaged or worn
should be properly repaired or replaced by an authorised service centre.
■
Make sure that the cutting attachment is properly installed and securely
fastened.
■
Never operate the product unless all guards, deflectors, and handles are
properly and securely attached.
■
Consider the environment in which you are working. Keep the working
area free from wires, sticks, stones, and debris, which if struck by the
cutter can become thrown objects.
BATTERY TOOL USE AND CARE
■
Recharge only with the charger specified by the manufacturer. A charger
that is suitable for one type of battery pack may create a risk of fire when
used with another battery pack.
■
Use power tools only with specifically designated battery packs. Use of
any other battery packs may create a risk of injury and fire.
■
When the battery pack is not in use, keep it away from other metal objects,
like paper clips, coins, keys, nails, screws, or other small metal objects that
can make a connection from one terminal to another. Shorting the battery
terminals together may cause burns or a fire.
■
Under abusive conditions, liquid may be ejected from the battery; avoid
contact. If contact accidentally occurs, flush with water. If liquid contacts
eyes, additionally seek medical help. Liquid ejected from the battery may
cause irritation or burns.
LINE TRIMMER SAFETY WARNINGS
■
Never allow children, persons with reduced physical, sensory, or mental
capabilities or with lack of experience and knowledge, or people who are
unfamiliar with these instructions to use the product.
■
Use the product in daylight or with good artificial light.
■
Avoid using the product on wet grass.
■
Keep proper footing and balance at all times, and be sure of proper
footing on slopes.
■
Do not walk backwards when using the product.
■
Walk, never run.
■
Keep the head attachment below waist level.
■
Never operate the product with damaged guards or without guards in
place.
■
Do not fit a metal replacement line.
■
Keep hands and feet away from the cutting means at all times, especially
when turning on the motor.
■
Beware, the cutting elements continue to rotate after the motor is turned
off.
■
Beware of objects thrown by the cutting means. Remove debris like
small stones, gravel, and other foreign objects from the work area before
starting operation. Wires or string may become entangled with the
cutting means.
■
To reduce the risk of injury associated with contacting moving parts,
always turn off the product, remove the battery pack, and allow both to
cool down. Make sure that all moving parts have come to a complete stop:
●
before servicing
●
before clearing a blockage
●
before checking, cleaning, and working on the product
●
before changing accessories
●
after striking a foreign object
●
whenever leaving the product unattended
28
●
whenever performing maintenance
●
whenever the product starts to vibrate abnormally
■
Wear full eye and hearing protection while operating the product. If
working in an area where there is a risk of falling objects, head protection
must be worn.
■
The use of hearing protection may restrict the operator's ability to hear
warning sounds. Pay particular attention to potential hazards around and
inside the working area.
■
Wear heavy, long trousers, boots, and gloves. Do not wear loose-fitting
clothing, short trousers, or jewellery of any kind, and do not use the
product with bare feet.
■
Secure long hair so that it is above shoulder level to prevent entanglement
in moving parts.
■
The small blade fitted to the lawn guard is designed to trim the new
extended line to the correct length for safe and optimum performance.
It is very sharp. Do not touch the blade, particularly when cleaning the
product.
■
Always ensure that ventilation openings are kept clear of debris.
■
Before use and after any impact, check that there are no damaged parts
on the product. A defective switch or any part that is damaged or worn
should be properly repaired or replaced by an authorised service centre.
■
Make sure that the cutting head attachment is properly installed and
securely fastened.
■
Make sure that all guards, deflectors, and handles are properly and
securely attached.
■
Do not modify the product in any way. This may increase the risk of injury
to yourself or others.
■
Use only the manufacturer's replacement cutting line. Do not use any
other cutting attachment.
■
Immediately turn off the product and remove the battery pack in the
event of accident or breakdown. Do not operate the product again until it
has been fully checked by an authorised service centre.
■
Do not dispose of used battery packs in the household refuse or by
burning them. AEG distributors offer to retrieve old batteries to protect
our environment.
■
Do not store the battery pack together with metal objects (short circuit
risk).
■
Battery acid may leak from damaged batteries under extreme load or
extreme temperatures. In case of contact with battery acid, wash it off
immediately with soap and water. In case of eye contact, rinse thoroughly
for at least 10 minutes and immediately seek medical attention.
WARNING! Ensure that the line cut-off blade in the guard is properly
positioned and secured before each use.
WARNING! Make sure to assemble the two-piece guard correctly
before use.
ADDITIONAL BATTERY SAFETY WARNINGS
WARNING! To reduce the risk of fire, personal injury, and product
damage due to a short circuit, never immerse your tool, battery pack, or
charger in fluid or allow fluid to flow inside them. Corrosive or conductive
fluids, such as seawater, certain industrial chemicals, and bleach or
bleach-containing products, etc., can cause a short circuit.
TRANSPORTATION AND STORAGE
■
Turn off the product, remove the battery pack, and allow the product to
cool down before storing or transporting.
■
Remove all foreign material from the product.
■
Do not store or transport the product with the battery pack fitted.
Remove the battery pack and secure it separately. Store the product in
a cool, dry, and well-ventilated place that is inaccessible to children. Keep
the product away from corrosive agents, such as garden chemicals and
de-icing salts. Do not store the product outdoors.
■
For transportation in vehicles, secure the product against movement or
falling to prevent injury to persons or damage to the product.
28
TRA
Tran
and
whe
Ensu
mate
non-
leak
MA
acce
can
shou
prod
use
■
■
■
■
■
■
■
■
RE
E
ve
elim
use,
■
■
■
RIS
It ha
to a
num
cold
work
sym
redu
■
■
■
If y
disc
Advertisement
