Download Print this page
Leviton 47611-GT4 Quick Start Manual
Leviton 47611-GT4 Quick Start Manual

Leviton 47611-GT4 Quick Start Manual

10/100 mbps four-port internet gateway
Hide thumbs Also See for 47611-GT4:

Advertisement

IMPORTANT INSTRUCTIONS
1.
Read and understand all instructions. Follow all warnings
and instructions marked on the product.
2.
Do not use this product near water—e.g., near a tub,
wash basin, kitchen sink or laundry tub, in a wet
basement, or near a swimming pool.
3.
Never push objects of any kind into this product through
openings, as they may touch dangerous voltages.
4.
SAVE THESE INSTRUCTIONS.
59-25 Little Neck Parkway
Little Neck, NY 11362-2591
Phone: (800) 323-8920
Fax: 1-800-832-9538
SAFETY INFORMATION
1.
Never install communications wiring or components
during a lightning storm.
2.
Never install communications components in wet
locations unless the components are designed
specifically for use in wet locations.
3.
Never touch uninsulated wires or terminals unless the
wiring has been disconnected at the network interface.
4.
Use caution when installing or modifying communications
wiring or components.
10/100 Mbps Four-Port Internet
Gateway
The 10/100Mbps Four-Port Internet Gateway is an easy-to-use router that offers small
office and home office (SOHO) an economical way to connect an entire local area network
(LAN) to the Internet using an external DSL/Cable Modem.
Follow this Quick-Start Guide to mount the Gateway into your Structured Media™ Center
(SMC), and configure it for normal network operation.
PRE-INSTALLATION CHECKLIST
To install the Gateway, you must have the following:
• A network interface card (NIC) installed in your computer.
• An external Cable or DSL modem with an RJ-45 port.
• (4) patch cords with RJ-45 connectors. Leviton Category 5e Performance Patch Cords
are recommended.
• A Leviton Category 5e Voice and Data Module (PN# 47605-C5) located in an SMC.
• At least 2 Category 5e data connectors (in addition to any desired telephone jacks),
wired back to the Category 5e Voice and Data Module with Category 5e cable. Mark
these
two
connectors
and
(Figure 2, page 5)
• An operational Internet connection/ISP.
• A Web browser installed on your computer.
• Specific ISP information for your broadband connection service; including: type of
protocol (PPPoE, Dynamic IP, or Fixed IP) and pertinent login information.
For Technical Assistance Call:
1-800-824-3005 (U.S.A. Only)
or Fax:
1-800-824-9538 (U.S.A. Only)
www.leviton.com
47611-GT4
Quick-Start Guide
corresponding
ports
"A"
and
DI-008-47611-00A
"B".
1

Advertisement

loading

Summary of Contents for Leviton 47611-GT4

  • Page 1 • (4) patch cords with RJ-45 connectors. Leviton Category 5e Performance Patch Cords are recommended. • A Leviton Category 5e Voice and Data Module (PN# 47605-C5) located in an SMC. • At least 2 Category 5e data connectors (in addition to any desired telephone jacks), wired back to the Category 5e Voice and Data Module with Category 5e cable.
  • Page 2 NOTE: To remove the bracket from the Gateway, loosen the nuts underneath the Gateway and bracket combination, then slide the units apart. NOTE: For information on installing the SMC or the Leviton Category 5e Voice and Data Module, please see the instructions for those devices.
  • Page 3: Configuring The Gateway

    2. Once the Gateway firmware is contacted, you should see a prompt for a user name and password. Leave the user name field blank and type "leviton" in lower case in the password field. The password is case sensitive; do not include the quotation marks.
  • Page 4 FCC STATEMENT: Figure 2 This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.