Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for GardenBeaut GB-R30
Summary of Contents for GardenBeaut GB-R30
- Page 1 USER MANUAL FOR GB-R30 (GB-R0) WOOD CHIPPER W W W . E F C U T . C O M...
-
Page 2: Table Of Contents
Section Page No INTRODUCTION PARTS LOCATOR SAFE WORKING Operator's Personal Protective Equipment (PPE) Basic Wood Chipping Safety General Safety Matters Recommissioning After Storage Safe Transportation Delivery Assembly Guide Start And Stop the Engine Daily Checks Before Starting Starting To Chip Chipping Blockages Refueling Engine Maintenance Schedule Resharpening Replacement of Blade Chipping System Guide To Replace Blades TROUBLESHOOTING Unable To Start ‐ Backfire Happens Unable To Start ‐ Test The Oil Alarm Device Inspection For Gasoline Leak HAZARDOUS MATERIALS AND END OF MACHINE LIFE During Machine Life End Of Machine Life ... -
Page 3: Introduction
USER MANUAL FOR GB-R30 (GB-R0) WOOD CHIPPER INTRODUCTION Thank you for choosing R30 (R0) wood chipper that is designed to give safe and dependable service if operated according to the instructions. IMPORTANT HEALTH AND SAFETY INFORMATION Before using your new chipper, please take time to read this manual. Failure to do so CAUTION or WARNING could result in：... -
Page 4: Parts Locator
USER MANUAL FOR GB-R30 (GB-R0) WOOD CHIPPER PARTS LOCATOR Code Part Q’ty Code Part Q’ty 1 901‐11E‐01 Housing 1 18 801‐075 M6 x 20 hex screw 2 2 901‐11E‐02 Cover of housing 1 19 803‐012 M6 locknut 12 3 901‐11E‐03 Cutting roller 1 20 801‐067 M6 x 35 Flanged hex screw 4 ... -
Page 5: Safe Working
USER MANUAL FOR GB-R30 (GB-R0) WOOD CHIPPER SAFE WORKING OPERATOR'S PERSONAL PROTECTIVE EQUIPMENT (PPE) Chainsaw safety helmet (EN 397) fitted with mesh visor (EN 1731) and ear defenders (EN 352). Work gloves with elasticated wrist. Steel toe cap safety boots (EN 345-1). -
Page 6: General Safety Matters
USER MANUAL FOR GB-R30 (GB-R0) WOOD CHIPPER GENERAL SAFETY MATTERS Always stop the chipper engine before making any adjustments, refueling or cleaning. Always check the rotor has stopped rotating before maintenance of any kind, or whenever the machine is to be left unattended. -
Page 7: Recommissioning After Storage
USER MANUAL FOR GB-R30 (GB-R0) WOOD CHIPPER RECOMMISSIONING AFTER STORAGE Ensure machine is stable. Undertake electrical diagnostic continuity check, to Remove all guards and check all fasteners. If necessary, confirm circuit is complete. retighten as described within this manual. -
Page 8: Assembly Guide
USER MANUAL FOR GB-R30 (GB-R0) WOOD CHIPPER ASSEMBLY GUIDE Step 1 Step 4 Fit support and engine base assembly together with R1. Install handle with R4. Step 2.1 Step 5.1 Fit tires and bracket together. Install feeding chute. Step 2.2 Step 5.2 ... -
Page 9: Start And Stop The Engine
USER MANUAL FOR GB-R30 (GB-R0) WOOD CHIPPER IMPORTANT: must r efer to the included Gasoline Engine Owner’s Manual for all information related to the engine, content in this manual is to add, not replace, the information. START AND STOP THE ENGINE Refer to page 13-17 of Gasoline Engine Owner’s Manual. -
Page 10: Refueling
USER MANUAL FOR GB-R30 (GB-R0) WOOD CHIPPER Continuing to feed the chipper with brushwood once it has become blocked will cause the chipper to compact the chips in the rotor housing and it will be difficult and time-consuming to clear. -
Page 11: Chipping System
USER MANUAL FOR GB-R30 (GB-R0) WOOD CHIPPER CHIPPING SYSTEM No. Part # Part description Q’ty 1 901‐11E‐03‐1 Cutting roller 1 L120 blade with two 2 301‐016 2 cutting edges 3 801‐078 5/16‐24 hex screw L=20 4 4 302‐004 116 fixed blade 1 5 802‐005 M10 flat washer 2 6 802‐007 M10 spring washer 2 7 ... -
Page 12: Guide To Replace Blades
USER MANUAL FOR GB-R30 (GB-R0) WOOD CHIPPER GUIDE TO WARNING REPLACE BLADE OR CUTTING EDGE WEAR RIGGERS GLOVES FOR THE BLADE CHANGING OPERATION. Step 1 Step 5 Unscrew M8 x 16 Flanged hex screw fixing the feeding chute. Loosen M10x25 hex screw (part # 801‐076) with 16mm socket spanner, move 116 fixed blade down to the lowest position of the slot hole. Step 2 Turn feeding chute up. Unscrew and remove red plastic cap. ... -
Page 13: Troubleshooting
USER MANUAL FOR GB-R30 (GB-R0) WOOD CHIPPER TROUBLESHOOTING This table is a troubleshooting guide to common problems. If the issue you are meeting is not listed below, please refer to SUPPORT on page 17 for further support. Caution - Always ensure... -
Page 14: Unable To Start - Backfire Happens
USER MANUAL FOR GB-R30 (GB-R0) WOOD CHIPPER Unable to start - backfire happens Place machine on level ground. Make sure the oil and gasoline are filled up. The oil dipstick should be wiped clean before measure. Drain out fluids within carburetor (refer to RECOMMISSIONING AFTER STORAGE on page 5). - Page 15 USER MANUAL FOR GB-R30 (GB-R0) WOOD CHIPPER 3. Check the carburetor screws are tight or carburetor floats are stuck. If the screw pointed by the yellow arrow is loose, tighten it enough. If gasoline flows out from the pipe pointed by red arrow, it...
-
Page 16: Hazardous Materials And End Of Machine Life
USER MANUAL FOR GB-R30 (GB-R0) WOOD CHIPPER HAZARDOUS MATERIALS END OF MACHINE LIFE During Machine Life The following hazardous materials are supplied within EFCUT machine： Engine oil Petrol Copper Ease MATERIAL SAFETY DATA SHEETS FOR HAZARDOUS MATERIALS SUPPLIED WITHIN EFCUT MACHINES ARE AVAILABLE ON REQUEST.REFER TO THESE FOR FIRST AID AND FIRE... -
Page 17: Decals
USER MANUAL FOR GB-R30 (GB-R0) WOOD CHIPPER DECALS Decal Description Decal Description Warning Check window for High velocity replacement of discharge - keep blades clear. Personal Protective Danger Equipment required. Rotating blades. Read Instruction Keep hands and Manual feet out. -
Page 18: Packing List
USER MANUAL FOR GB-R30 (GB-R0) WOOD CHIPPER Packing List Part Q’ty Image Main body assembly 1pc. Engine base Bracket 1pc. Support base Tires 2pcs Supports 1pc. Discharge chute assembly 1pc. Bottom feed hopper 1pc. Handle 1pc. 16 ... -
Page 19: Support
USER MANUAL FOR GB-R30 (GB-R0) WOOD CHIPPER SUPPORT Limited warranty One (1) year warranty against machine construction except blades and other consumables etc. https://www.efcut.com/support/product-reg/ Register your machine at https://www.efcut.com/support/after-sale-service-inquiry/ Submit after-sale service ticket at Note: must provide SN # below when after-sale service or technical support... - Page 20 GARDENBEAUT Maker of Garden Beaut ...