Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for GardenBeaut GB-S3.1
Summary of Contents for GardenBeaut GB-S3.1
- Page 1 USER MANUAL FOR GB-S3.1 WOOD CHIPPER W W W . E F C U T . C O M...
-
Page 2: Table Of Contents
Section Page No INTRODUCTION PARTS LOCATOR SAFE WORKING Operator's Personal Protective Equipment (PPE) Basic Wood Chipping Safety General Safety Matters Recommissioning After Storage Safe Transportation Delivery Assembly Guide Start And Stop the Engine Daily Checks Before Starting Starting To Chip Chipping Blockages Refueling Engine Maintenance Schedule Resharpening Replacement of Blade Chipping System Guide To Replace Blades TROUBLESHOOTING Unable To Start ‐ Backfire Happens Unable To Start ‐ Test The Oil Alarm Device Inspection For Gasoline Leak HAZARDOUS MATERIALS AND END OF MACHINE LIFE During Machine Life End Of Machine Life DECALS PACKING LIST SUPPORT... -
Page 3: Introduction
USER MANUAL FOR GB-S3.1 WOOD CHIPPER INTRODUCTION Thank you for choosing GB-S3.1 wood chipper that is designed to give safe and dependable service if operated according to the instructions. IMPORTANT HEALTH AND SAFETY INFORMATION Before using your new chipper, please take time to read this manual. Failure to do so CAUTION or WARNING could result in：... -
Page 4: Parts Locator
USER MANUAL FOR GB-S3.1 WOOD CHIPPER PARTS LOCATOR Code Name Q'ty Code Name Q'ty 101-001D 212cc gas engine 801-030 M8 x 16 Flanged hex bolt 902-12C-02A Front cover of housing 803-005 M8 Flanged locknut 902-12C-05A Removable cover of housing... -
Page 5: Safe Working
USER MANUAL FOR GB-S3.1 WOOD CHIPPER SAFE WORKING OPERATOR'S PERSONAL PROTECTIVE EQUIPMENT (PPE) Chainsaw safety helmet (EN 397) fitted with mesh visor (EN 1731) and ear defenders (EN 352). Work gloves with elasticated wrist. Steel toe cap safety boots (EN 345-1). -
Page 6: General Safety Matters
USER MANUAL FOR GB-S3.1 WOOD CHIPPER GENERAL SAFETY MATTERS Always stop the chipper engine before making any adjustments, refueling or cleaning. Always check the rotor has stopped rotating before maintenance of any kind, or whenever the machine is to be left unattended. -
Page 7: Recommissioning After Storage
Turn the fuel valve OFF and keep the engine upright. DELIVERY All GB-S3.1 wood chippers have a full pre delivery inspection before leaving the factory and are ready to use. Read and understand this instruction manual before attempting to operate the chipper. -
Page 8: Assembly Guide
USER MANUAL FOR GB-S3.1 WOOD CHIPPER ASSEMBLY GUIDE Step 1 Step 5 Fit support and main body assembly together with R1. Install bottom hopper with R5,R6. Step 2 Step 6 Fit tires and bracket together with R2. Install upper hopper with R7... -
Page 9: Start And Stop The Engine
USER MANUAL FOR GB-S3.1 WOOD CHIPPER IMPORTANT: must r efer to the included Gasoline Engine Owner’s Manual for all information related to the engine, content in this manual is to add, not replace, the information. START AND STOP THE ENGINE Refer to page 13-17 of Gasoline Engine Owner’s Manual. -
Page 10: Refueling
USER MANUAL FOR GB-S3.1 WOOD CHIPPER Continuing to feed the chipper with brushwood once it has become blocked will cause the chipper to compact the chips in the rotor housing and it will be difficult and time-consuming to clear. -
Page 11: Chipping System
USER MANUAL FOR GB-S3.1 WOOD CHIPPER CHIPPING SYSTEM Part description Q’ty Flywheel assembly M8 lock nut Blade M8 x 25 Hexagon countersunk head bolt 9 ... -
Page 12: Guide To Replace Blades
USER MANUAL FOR GB-S3.1 WOOD CHIPPER GUIDE TO REPLACE BLADE WARNING WEAR RIGGERS GLOVES FOR THE BLADE CHANGING OPERATION. 1. Turn engine off as per instruction. 2. Pull the plug cap from the spark plug. 3. Remove Bottom Feed Hopper. -
Page 13: Troubleshooting
USER MANUAL FOR GB-S3.1 WOOD CHIPPER TROUBLESHOOTING This table is a troubleshooting guide to common problems. If the issue you are meeting is not listed below, please refer to SUPPORT on page 17 for further support. Caution - Always ensure... -
Page 14: Unable To Start - Backfire Happens
USER MANUAL FOR GB-S3.1 WOOD CHIPPER Unable to start - backfire happens Place machine on level ground. Make sure the oil and gasoline are filled up. The oil dipstick should be wiped clean before measure. Drain out fluids within carburetor (refer to RECOMMISSIONING AFTER STORAGE on page 5). -
Page 15: Inspection For Gasoline Leak
USER MANUAL FOR GB-S3.1 WOOD CHIPPER Inspection for gasoline leak 1. Check the gasoline pipe to fuel switch is connected properly and solidly. 2. Check the gasoline pipe under gasoline tank is connected properly and solidly. 3. Check the carburetor bolts are tight or carburetor floats are stuck. -
Page 16: Hazardous Materials And End Of Machine Life
USER MANUAL FOR GB-S3.1 WOOD CHIPPER HAZARDOUS MATERIALS END OF MACHINE LIFE During Machine Life The following hazardous materials are supplied within EFCUT machine： Engine oil Petrol Copper Ease MATERIAL SAFETY DATA SHEETS FOR HAZARDOUS MATERIALS SUPPLIED WITHIN EFCUT MACHINES ARE AVAILABLE ON REQUEST.REFER TO THESE FOR FIRST AID AND FIRE... -
Page 17: Decals
USER MANUAL FOR GB-S3.1 WOOD CHIPPER DECALS Decal Description Decal Description Warning Check window for High velocity replacement of discharge - keep blades clear. Personal Protective Danger Equipment required. Rotating blades. Read Instruction Keep hands and Manual feet out. -
Page 18: Packing List
USER MANUAL FOR GB-S3.1 WOOD CHIPPER Packing List Part Q’ty Image Main body assembly 1pc. Bracket 1pc. Tires 2pcs Supports 1pc. Discharge chute assembly 1pc. Bottom feed hopper 1pc. Upper feed hopper 1pc. Handle 1pc. 16 ... -
Page 19: Support
USER MANUAL FOR GB-S3.1 WOOD CHIPPER SUPPORT Limited warranty One (1) year warranty against machine construction except blades and other consumables etc. https://www.efcut.com/support/product-reg/ Register your machine at https://www.efcut.com/support/after-sale-service-inquiry/ Submit after-sale service ticket at Note: must provide SN # below when after-sale service or technical support... - Page 20 GARDENBEAUT Maker of Garden Beaut ...