Advertisement
Quick Links
Advertisement
Related Manuals for PCB Piezotronics 478B05
Summary of Contents for PCB Piezotronics 478B05
- Page 1 Model 478B05 3 Channel DC Sensor Signal Conditioner Installation and Operating Manual For assistance with the operation of this product, contact PCB Piezotronics, Inc. Toll-free: 800-828-8840 24-hour SensorLine: 716-684-0001 Fax: 716-684-0987 E-mail: info@pcb.com Web: www.pcb.com...
- Page 2 Returning Equipment – Following the equipment to PCB Piezotronics for these procedures will insure that your repair. User servicing or repair is not returned materials are handled in the recommended and, if attempted, may most expedient manner.
- Page 3 PCB Piezotronics, Inc. Warranty – All equipment and repair 3425 Walden Ave. services provided by PCB Piezotronics, Depew, NY 14043 USA Inc. are covered by a limited warranty Toll-free: (800) 828-8840 against defective...
- Page 4 DC SENSOR DIVISION The Model 478A05 Capacitive Accelerometer Power Supply Operating Guide with Enclosed Warranty Information 3425 Walden Avenue, Depew, New York 14043-2495 DCS Toll Free 888-684-0014 24 Hour SensorLine™ 716-684-0001 Fax 716-685-3886 E-mail dcs@PCB.com MANUAL NUMBER: 18661 MANUAL REVISION: NR...
-
Page 5: Table Of Contents
DC SENSOR DIVISION table of contents Introduction........................page 3 Description ........................page 3 Warning Symbols & Terms....................page 3 Operation........................pages 4-6 Figure 1 – Model 478A05 Capacitive Accelerometer Power Supply ......page 4 Figure 2 – Model 478A05 Sensor Input Terminal Strip ..........page 6 ESD Warning Information.................... -
Page 6: Introduction
DC SENSOR DIVISION introduction Congratulations on the purchase of a quality PCB Signal Conditioner. In order to ensure the highest level of performance for this product, please familiarize yourself with the safety and operation procedures before attempting to operate this device. If you have any additional questions concerning this unit or its application, feel free to call a factory application engineer at (716) 684-0001. -
Page 7: Operation
DC SENSOR DIVISION figure 1 - model 478A05 capacitive accelerometer power supply operation To turn on the Model 478A05, connect the 488A04 Power Supply to the DIN connector on the back of the unit and press the black switch on the front panel to the 1 position. A green power indicator light will illuminate. A red fault light is provided on the front panel to indicate a problem with the power supply to the sensor. - Page 8 DC SENSOR DIVISION operation continued . . . Input connection to the unit is made as follows: For the 3703 Triaxial Accelerometer and 037Pxx Cable, with a typical configuration of the X, Y, and Z axis corresponding to Ch. 1, Ch.2 and Ch. 3 respectively: ...
- Page 9 DC SENSOR DIVISION figure 2 - model 478A05 sensor input terminal strip operation continued . . . All Self Test connections are internally connected to ground to avoid offset drift in the sensor. The SHIELD connection is internally capacitively coupled to signal ground. This is an optional connection used to correct possible noise issues.
-
Page 10: Esd Warning Information
2 – ESD sensitivity This equipment is designed with user safety in mind; however, the protection provided by the equipment may be impaired if the equipment is used in a manner not specified by PCB Piezotronics, Inc. caution 1 – ESD sensitivity Cables can kill your equipment. -
Page 11: Warranty, Maintenance & Repair Procedure
3425 Walden Avenue, Depew, NY 14043-2495 DCS Toll Free 888-684-0014 24 Hour SensorLine™ 716-684-0001 Fax 716-685-3886 E-mail dcs@PCB.com ICP ® is a registered trademark of PCB Piezotronics, Incorporated, which uniquely identifies PCB sensors that incorporate built-in microelectronics. PAGE 8...
Need help?
Do you have a question about the 478B05 and is the answer not in the manual?
Questions and answers