1. Manuals
  2. Brands
  3. HELLO LITE Manuals
  4. Lighting Equipment
  5. HW-01
  6. Operation instruction manual

HELLO LITE HW-01 Operation Instruction Manual

Stage special effect spark machine
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
Operation Instruction for
the Stage Special Effect
Spark Machine

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the HW-01 and is the answer not in the manual?

Questions and answers

Related Manuals for HELLO LITE HW-01

Summary of Contents for HELLO LITE HW-01

  • Page 1 Operation Instruction for the Stage Special Effect Spark Machine...
  • Page 2 This instruction contains important information. Please read the instruction before making the machine. Every time you have finished adding consumables, please cover the lid immediately. It is strictly forbidden to spark without the lid. When you ignite the consumables carelessly, please use sand to extinguish them. You can't use water.

  • Page 3: Machine Parameter

    7. For better heat dissipation, do not block the intake and exhaust ports. 8. No object should be used to seal the nozzle. Machine parameter Model number HW-01 Jetting height 1-5 meter Operating temperature -10℃-50℃ Power power 600w 3.8A (110V )/ 600w 1.9A...

  • Page 4: Material Parameters

    Material parameters Consumables Titanium composite article Net weight suttle 45 g/200g It can take 4-15 minutes. Time time It can take 4-15 minutes Packaging package Vacuum package Operation steps: 1.When the machine is not connected to DMX, the machine automatically preheates after starting (when DMX signal is connected, CH1 channel value 240-255 is ready).
  • Page 5 the corresponding key of F06 is No. 6 on the machine display (the range of the address code of the remote controller is adjustable from 1 to 6). 2.Preheating mode:No. 1 green indicator READY flickers, No. 4 red indicator HEAT lights up, indicating that it has entered the preheating state, the preheating is completed, No.
  • Page 6 1. Contents displayed in the machine display area: 1)F01, F02, F03, F04, F05, F06 (when the remote control is in control state, the default display area shows F1-F6 as the address code of the remote control is adjustable). 2)DMX512 Address (When connecting to DMX, the default display area shows that DMX512 Address 1-510 is adjustable corresponding to DMX1-510 Address Code)
  • Page 7 P01, P02. At this time, you can switch function number by pressing left and right key. Long press left key to enter the function number parameter setting interface, short press left key to increase the function number parameter, short press right key function number parameter to reduce, after setting is completed, often press left key to confirm.
  • Page 8 3. DMX512 address parameters 512 channel value function 0 - 10 Stop running 11 - 179 Emergency stop 180 - 199 Clear material Protocol 200 - 219 switching Wireless 220 - 239 machine 240 - 255 Operation Density control 0-255 increment Height control 0-255...

  • Page 9: Remote Controller Description

    2. Actual Operating Channel 1 goes to the Operating Address Code. 3. Channel 2 is a density channel. 4. Channel 3 is height channel Remote Controller Description Before using the remote control, the antenna should be pulled out to achieve the best control effect.
  • Page 10 No. 6 address number on/off, press No. 6 key, the machine 6 KEY: starts, press No. 6 key again, the machine stops; after pressing No. 6 key, the machine runs for 8 seconds by default. 。 Spark 1.5 seconds from 1-6 address once, time 7 KEY: interval is 0.5 seconds, cycle is 3 times, 1.5 seconds for extension 1, 0.5 seconds for extension 2, 1.5 seconds for...
  • Page 11 Operating panel instructions 1： Connect the power input cable, press the ON key of the main switch of the power supply, the preheating indicator HEAT will turn on the red light, READY indicator flashes, indicating that the preheating of the machine takes about 5 minutes.

  • Page 12: Warranty Notes

    The parameter confirmation needs long pressing the left key, and long press the right key for the return operation. 4: Long press the minus sign on the left most -, the system will display P00 (P00 represents the address code of the remote controller, the parameter range is 1-6 adjustable).
  • Page 13 4. Any one of the following circumstances does not fall within the scope of warranty service: 1. Damage caused by external reasons or failure to operate in accordance with the instructions; 2. The product has been disassembled, modified or repaired without authorization;...

  • Page 14: Warranty Card

    Warranty card Product name Product number Date of purchase Contact address Contact number User Feedback Information Failure Disposal Repairing personnel Reparing date...

Table of Contents