Klipsch SB 120 Manual
Also See for SB 120:

Advertisement

Klipsch SB 120 Manual

WHAT'S INSIDE

Overview

DIGITAL OPTICAL CONNECTION

(PREFERRED - IF TV HAS NO OPTICAL OUT SEE NEXT SECTION)

Digital Optical Connection

3.5mm TO DUAL RCA ANALOG CONNECTION

(IF TV HAS NO HEADPHONE OUT SEE NEXT SECTION)

3.5mm to Dual RCA Analog Connection

DUAL RCA TO DUAL RCA ANALOG CONNECTION

(CABLES NOT INCLUDED)

Dual RCA to Dual RCA Analog Connection

TV REMOTE PROGRAMMING

TV Remote Programming

To program Volume Up and Volume Down buttons repeat the steps shown and replace steps 4 and 6 with the button you want to program.

If you are trying to program a cable/satellite box remote or other universal remote without success, please try programming your TV or Cable Box remote instead.

BLUETOOTH® WIRELESS TECHNOLOGY

Bluetooth Connection Step 1
Bluetooth Connection Step 2
Bluetooth Connection Step 3

* Example only. Your device may differ.

You can pair a device equipped with Bluetooth at any time by activating it on your device.

Once your device equipped with Bluetooth is paired, the SB 120 will automatically switch to the Bluetooth input (SOLID BLUE LIGHT) and you can stream your music. If you switch inputs on the SB 120, the Bluetooth connection will automatically be terminated.

You must disconnect your device before pairing another device equipped with Bluetooth by either:

  • Pressing and holding the SOURCE button on the SB 120 control panel 3 seconds
  • Turning off Bluetooth on the paired device
  • Pressing the Bluetooth button () on the SB 120 remote

BUTTONS

Buttons

STATUS LIGHTS

(RIGHT STATUS LIGHT, UNLESS STATED)

SOLID RED Power Off (Standby Mode)
SOLID GREEN Power On, Source is Optical Input
SOLID ORANGE Power On, Source is Analog Input
SOLID BLUE Power On, Source is Paired Bluetooth device
FLASHES GREEN / ORANGE / BLUE Volume Up, Volume Down, Subwoofer Volume Up or Subwoofer Volume Down is pushed
FLASHES BLUE QUICKLY Waiting to pair with Bluetooth device
FLASHES PURPLE SLOWLY SB 120 decoding Dolby Digital
SOLID WHITE 3D Surround Mode On (Left Status Light)

STANDBY MODE

You do not need to turn off the SB 120, just turn off your TV (or Satellite / Cable Box) and the SB 120 will automatically go into standby mode in approximately 10 minutes.

Standby mode is indicated by a red status light on the front panel. When your TV (or Satellite / Cable Box) is turned back on the SB 120 will automatically turn on again.

PLACEMENT

Placement Step 1Placement Step 2

Make sure the rear of the SB 120 is at least one inch away from a back wall and there is at least one inch clearance around the top and sides of the SB 120 for ventilation. Make sure to center your TV on the SB 120.

TURN OFF TV SPEAKERS

Turn off TV Speakers

CARE AND CLEANING

Care and Cleaning

TROUBLESHOOTING

SB 120 will not Power On

  • Is it plugged into a live outlet?
  • Is the rear power switch on?

No sound

  • Is it plugged into a live outlet and the rear power switch is on?
  • Are all cables from the TV/Cable Box/Satellite Box plugged in tightly?
  • If the optical cable is being used were the clear plastic caps from both ends removed before connecting?
  • Is the volume turned up?
  • Is standby off (no SOLID RED status light)?
  • Is the source input correct?
  • Turn off the rear power switch, then back on.

TV/Cable/Satellite Box Remote will not program

  • Carefully follow all remote programming instructions.
  • Carefully go through the remote programming again, but use the original remote that comes with the TV. You DO NOT need to then reprogram using your cable/satellite/universal remote control.
  • Program the original TV remote to the SB 120 (if original is a different one), then use the universal remote without programming it.
  • You may need to repeat programming of a function in some cases.
  • There may be some cases the SB 120 is unable to learn certain remote codes.

Bluetooth does not work

  • Is the device paired to the SB 120?
  • Move your device closer to the SB 120 and make sure it is paired.
  • If the status light blinks RED while attempting to pair, start the pairing process over.


Manufactured under license from Dolby Laboratories. Dolby and the double-D symbol are registered trademarks of Dolby Laboratories.

The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by Klipsch Group, Inc. is under license.

Videos

Klipsch HD Theater SB 120 Setup Guide Video

Documents / Resources

Download manual

Here you can download full pdf version of manual, it may contain additional safety instructions, warranty information, FCC rules, etc.

Download Klipsch SB 120 Manual

Advertisement

Need help?

Need help?

Do you have a question about the SB 120 and is the answer not in the manual?

Questions and answers

Table of Contents