If you install the product in a way that differs from this manual, this will void all guarantees. Before installation check that the product meets all your
requirements and is not damaged. By proceeding with installation, you accept the condition of the product.
Disclaimer
Indien u het product plaatst op een manier die afwijkt van deze handleiding, vervalt alle garantie. Controleer voor plaatsing of het product aan al uw eisen
voldoet en niet beschadigd is. Indien u overgaat tot plaatsing, aanvaardt u de staat waarin het product zich bevindt.
Clause de non-responsabilité
Si vous installez le produit d'une manière différente de celle présentée dans ce manuel, toutes les garanties seront invalidées. Contrôlez avant le placement si
le produit répond à toutes vos exigences et n'est pas endommagé. En procédant au placement, vous acceptez l'état dans lequel se trouve le produit.
Haftungsausschluss
Wenn Sie das Produkt nicht genau nach den Angaben in dieser Montageanleitung einbauen, verfällt die Garantie. Überprüfen Sie vor dem Einbau des Pro-
dukts, ob sämtliche Voraussetzungen erfüllt sind und das Produkt nicht beschädigt ist. Sobald Sie mit der Montage beginnen, sehen Sie, in welchem Zustand
Do you have a question about the SENSES and is the answer not in the manual?
Questions and answers
fred
March 11, 2025
luca vares senses sliding shower door ,does not close / open completly ,
i think i made a mistake installing part Z page 8 manual .what did i do wrong
1 comments:
Mr. Anderson
March 11, 2025
An installation mistake that could cause the Luca Varess SENSES sliding shower door to not close or open completely includes not following the instructions exactly as stated in the manual. Possible errors include:
1. Incorrect Glass Panel Orientation – If the decorative side of the glass panels and doors is not facing the outside of the shower, it may affect alignment and movement. 2. Improper Adjustment – If the door is not properly adjusted, gaps or misalignment may prevent smooth sliding. 3. Improper Locking – If the locking mechanisms or fasteners are not secured correctly, the door may not stay in place or move correctly. 4. Incorrect Measurements – If the installation does not follow the specified width adjustments (e.g., 593~613 mm for a 1200 mm door), the door may not fit or slide as intended. 5. Failure to Check for Damage – Installing a damaged component may cause operational issues.
Ensuring proper alignment, adjustment, and adherence to installation guidelines will help avoid these issues.
Page 1
SENSES sliding showerdoor Installationguide Installatiegids Guide d’installation Montageanleitung Safety TOOLS NEEDED SANITAIR Disclaimer If you install the product in a way that differs from this manual, this will void all guarantees. Before installation check that the product meets all your requirements and is not damaged.
Page 3
IMPORTANT = Shower size/Douchemaat Taille de la douche/Duschgröße 0~20mm Glass panels and doors with a decorative side (mat, mat striped or with special print) need to be installed with this decorative side facing the outside of the shower. Glaspanelen en glasdeuren met een decoratieve zijde (mat, mat gestreept of met speciale print) moeten met deze decoratieve zijde naar de buitenzijde van de douche worden geplaatst.
Need help?
Do you have a question about the SENSES and is the answer not in the manual?
Questions and answers
luca vares senses sliding shower door ,does not close / open completly , i think i made a mistake installing part Z page 8 manual .what did i do wrong
An installation mistake that could cause the Luca Varess SENSES sliding shower door to not close or open completely includes not following the instructions exactly as stated in the manual. Possible errors include:
1. Incorrect Glass Panel Orientation – If the decorative side of the glass panels and doors is not facing the outside of the shower, it may affect alignment and movement.
2. Improper Adjustment – If the door is not properly adjusted, gaps or misalignment may prevent smooth sliding.
3. Improper Locking – If the locking mechanisms or fasteners are not secured correctly, the door may not stay in place or move correctly.
4. Incorrect Measurements – If the installation does not follow the specified width adjustments (e.g., 593~613 mm for a 1200 mm door), the door may not fit or slide as intended.
5. Failure to Check for Damage – Installing a damaged component may cause operational issues.
Ensuring proper alignment, adjustment, and adherence to installation guidelines will help avoid these issues.
This answer is automatically generated