Time Keeping Mode - Setting The Daily Alarm And The Date Alarm; Time Keeping Mode - Start/Stop The Chronograph; Time Keeping Mode - Record/Recall A Lap Memory - La Crosse Technology K2-100 User Manual

4.4 Time Keeping Mode
- Setting the Daily Alarm and the Date Alarm
hour digits
have been
hold
selected
adjust
(flashing)
A
mode
button
A
Daily/Date Alarm Display Daily/Date Alarm Setting Display
adjust
hour minute
adjust
hold
Daily Alarm Setting Sequence
adjust
adjust adjust adjust
hour minute month day
adjust
Date Alarm Setting Sequence
start/stop hold start/stop lap/reset hold lap/reset
mode
button
Increase the minute Decrease the number
Increase Decrease
the number at a higher speed the number at a higher speed
4.5 Time Keeping Mode
- Start/Stop the Chronograph
chronograph
display indicator
1/100 sec the digits
keep running
start/stop
Chronograph
hour minutes seconds
Running Display
Chronograph
'Zero' Display
start/stop
the digits
stop running
hold
start/stop
lap/reset
Chronograph Stop Display
To Set The Daily Alarm
- Press and hold the [adjust] button for 2 seconds to change
f r o m D a i l y A l a r m D i s p l a y t o D a i l y A l a r m S e t t i n g
Display.
- The hour digits flash on the display because it is being
selected.
The Setting Procedure
- Press [adjust] button to change the selection in the
Daily Alarm Setting Sequence.
- While any digits are flashing (selected), press the [start/stop]
button to increase the number; press the [lap/reset] button to
decrease the number. Hold down the button to change the
number at a higher speed.
- After you set the alarm time, press the [mode] button to exit
the setting sequence.
- If no button is pressed in the setting display for about 3
minutes, the K2-100 will return to the Alarm Time Mode
automatically
To Set The Date Alarm
- Press and hold the [adjust] button for 2 seconds to change
from Date Alarm Display to Date Alarm Setting Display.
- The hour digits flash on the display because it is being
selected.
The Setting Procedure
- Press the [adjust] button to change the selection in the
Date Alarm Setting Sequence.
- Follow the Daily Alarm Setting steps to set the
subsequent settings of the Date Alarm.
8
9
Chronograph Mode
- The Chronograph measures elapsed times and lap-
times.
- The display shows the 'All Zeros' display when the
chronograph is being selected the first time or the
chronograph is reset.
- The chronograph resolution in 1/100 second.
To Start/Stop the Chronograph
- When the chronograph is idle, press the [start/stop]
button to start the chronograph; press the [start/stop]
button once again to stop the chronograph.
- The elapsed time between the 2-[start/stop]-keystoke
will appear on the display.
- Repeat the steps mentioned above to get another set
of elapsed time.
To Reset the Chronograph
- To record a new set of elapsed times, press and
hold the [lap/reset] button for 2 seconds to reset
t h e c h r o n o g r a p h t o t h e ' A l l Z e r o s ' d i s p l a y .
9
10
4.6 Time Keeping Mode
- Record/Recall a Lap Memory
the digits the lap
is running number
lap/reset
Chronograph Chronograph
Running Display LapDisplay
5 second
To record the Lap Memory
1st lap memory
hold adjust
lap/reset
mode
the next
lap memory
lap memory recall
Chronograph
sequence
Stop Display
To recall the Lap Time
10
4.7 Time Keeping Mode
- Countdown Timer and Repeat Timer
countdown timer repeater timer
the counting row
display indicator display indicator
the counting row
hPa
the setting row
Count Down Timer Display Repeater Timer Display
lap/reset lap/reset
3 min 5 min 10 min
lap/reset lap/reset lap/reset lap/reset
User
Pre-set
45 min 15 min
Value
(UPV)
Timer Setting Sequence
11
To Record Lap Memory
- The Chronograph Mode allows you to record up to 10
lap memories.
- Press the [lap/reset] button once to record the lap
memory while the chronograph is running.
- The lap number will be displayed at the right hand side of
the display for 5 seconds, as well as the lap time display
on the bottom row of the display. Then the chronograph
starts running again automatically.
- While the lap number and lap time are displayed, the
chronograph keeps running.
- Repeat the steps mentioned above to get another set of
lap memory.
To Recall Lap Memory
- Press and hold the [adjust] button to enter the lap
memory recall sequence, in the Chronograph Stop Display.
- Press the [lap/reset] button to switch among the lap
memories.
- Press the [mode] button to exit the lap memory recall
sequence.
To Reset Lap Memory
- T o r e c o r d n e w s e t s o f l a p t i m e , p r e s s a n d h o l d t h e
[lap/reset] button for 2 seconds to reset the chronograph
lap memory while the chronograph is stopped.
11
Countdown Timer and Repeat Timer Display
- The K2-100 h a s t w o t i m e r c o u n t i n g d i s p l a y s :
Countdown Timer and Repeat Timer.
- The Countdown Timer starts counting from the preset
value to zero and stops at zero.
- The Repeat Timer starts counting from the preset
value to zero and then the timer restarts the counting
again and again automatically until the [start/stop] button
is pressed.
- T o s e l e c t b e t w e e n C o u n t d o w n T i m e r a n d R e p e a t
Timer Display, check the 'Setting the Timer Counting
Display' section for more detail.
The Timer Display Format
- The 1st row of the display shows the Countdown Timer
or the Repeat Timer indicators.
- The 2nd row of the display shows the digits, which the
timer starts counting down from.
- The 3rd row of the display shows the digits, which the
timer is going to be set at.
To set the Timer from the Quick-Set-Values
- P r e s s t h e [ l a p / r e s e t ] b u t t o n t o s e l e c t a m o n g t h e 5
quick-set-values (3,5,10,15 and 45 min) and the existing
U s e r P r e - s e t V a l u e ( U P V ) a s i n t h e T i m e r S e t t i n g
Sequence.
- When the desired value displays on the 3rd row of the
d i s p l a y , p r e s s a n d h o l d t h e [ l a p / r e s e t ] b u t t o n f o r 2
seconds to load that value to the 2nd row of the display.
The timer is now set.
- To set the timer values other than the 5 quick-set-value
and the existing UPV , check the 'T o Set the User Pre-set
Value' section for detail.
12