Performance Furnishings PLCUBED20 Assembly Instructions

ASSEMBLY INSTRUCTIONS
1 2
MODEL: PLCUBED20
Cam Lock Klix Cam
18 Pcs 18 Pcs
Before assembly, please remove all parts from the carton, verifying that you have the correct quantities, and read all the instructions.
IN THE CARTON:
A B
Support Rail
1 2
Left & Right
Cam Lock Klix Cam
18 Pcs 18 Pcs
KLIX CAM INSTRUCTIONS ASSEMBLY INSTRUCTION FOR CUBE TABLE BASE
1
A B
Support Rail
Left & Right
Line up Cam Lock,
1 2 3
turn clockwise.
Housing
Cam Lock Klix Cam Cap (Long)
18 Pcs
18 Pcs 14 Pcs
KLIX CAM INSTRUCTIONS
1
A B
Line up Cam Lock,
turn clockwise.
Support Rail
Side Panel LEFT
Left & Right
IMPORTANT NOTE :
Place all wooden parts on a clean, smooth surface to prevent the parts from being scratched.
Check that you have all parts and hardware.
Remove all wrapping materials, including staples & packing straps before you start to assemble.
KLIX CAM INSTRUCTIONS
Do not tighten any screws or bolts until the unit is completely assembled.
Keep all hardware parts out of reach of children.
1
REV. 1
IMPORTANT NOTE :
Line up Cam Lock,
turn clockwise.
Place all wooden parts on a clean, smooth surface to prevent the parts from being scratched.
Check that you have all parts and hardware.
Remove all wrapping materials, including staples & packing straps before you start to assemble.
Do not tighten any screws or bolts until the unit is completely assembled.
Keep all hardware parts out of reach of children.
3 4 5
6
Housing Housing Adjustable
M6 x 40mm = 8pcs
Cap (Long) Cap (Short)
Glide
1
14 Pcs 4 Pcs
6 Pcs
ASSEMBLY INSTRUCTION FOR CUBE TABLE BASE
C
3 4 5
6
Side Panel LEFT Side Panel RIGHT
Housing Housing
Adjustable
M6 x 40mm = 8pcs
Cap (Long) Cap (Short)
Glide
1
14 Pcs 4 Pcs 6 Pcs
2
C
Insert the cam with the arrow
Side Panel LEFT Side Panel RIGHT
pointing towards the hole in the
4 5
6
edge.
Housing JCBC Screw
Adjustable
M6 x 40mm = 8pcs
Cap (Short)
Glide
1
Washer = 8pcs
4 Pcs
6 Pcs 4
2 COMPONENTS
C
Insert the cam with the arrow
pointing towards the hole in the
edge.
Side Panel RIGHT
2
Insert the cam with the arrow
pointing towards the hole in the
edge.
HARDWARE
7 8 9
6 Hole
Screw
JCBC Screw
L-Bracket
5
#6 x "
8 Door Hingers
4 Pcs
Washer = 8pcs 24 Pcs
4
COMPONENTS
D E
HARDWARE
7 8 9
Back Panel
Top Rail
6 Hole
Screw
JCBC Screw
L-Bracket
#6 x 5 "
8 Door Hingers
4 Pcs
Washer = 8pcs 24 Pcs
4
COMPONENTS
3
D E
HARDWARE
Insert the Cam Lock into Klix
Back Panel
Top Rail
Cam. Turn Klix Cam to lock.
7 8
6 Hole
Screw
L-Bracket
5
#6 x "
8
4 Pcs
24 Pcs
A
B
D
3
A
E
D E
Insert the Cam Lock into Klix
G
C
Cam. Turn Klix Cam to lock.
Back Panel
Top Rail
A
B
D
A
E
3
G
C
Insert the Cam Lock into Klix
Cam. Turn Klix Cam to lock.
A
10 11 12
Screw
0' Compo Magnet
#3.5 x 16mm #3.5 x 12mm
Catches
2 Pcs
1 Pair 1 Set
ACCESS DOOR
F G
10 11 12
Bottom Rail
Screw
0' Compo Magnet
#3.5 x 16mm #3.5 x 12mm
Catches
2 Pcs
1 Pair 1 Set
HINGE INSTRUCTIONS
DETAIL x-x
ACCESS DOOR
F G
Bottom Rail
9 10 11
BACK VIEW
ADJUST THIS SCREW FOR DOOR ALIGNMENT
AFTER ASSEMBLY OF THE HINGES.
Magnet Screw
0' Compo
#3.5 x 16mm
Door Hingers Catches
2 Pcs
1 Pair 1 Set
HINGE INSTRUCTIONS
DETAIL x-x
F
BACK VIEW
ADJUST THIS SCREW FOR DOOR ALIGNMENT
AFTER ASSEMBLY OF THE HINGES.
Bottom Rail
HINGE INSTRUCTIONS
DETAIL x-x
BACK VIEW
ADJUST THIS SCREW FOR DOOR ALIGNMENT
AFTER ASSEMBLY OF THE HINGES.
13
M4 x 65
Screw
Allen-Key
1 Pc
2 Pcs
13
Door Panel
M4 x 65
Screw
Allen-Key
1 Pc
2 Pcs
Door Panel
12 13
M4 x 65
Screw
Allen-Key
#3.5 x 12mm
1 Pc
2 Pcs
G
Door Panel
PAGE 1 OF 2
PLCUBED20_AI
1 of 2.