1. Manuals
  2. Brands
  3. LXE Manuals
  4. Scanner
  5. 8650
  6. User manual

LXE 8650 User Manual

Bluetooth ring scanner
Hide thumbs
Table of Contents

Advertisement

Quick Links

Bluetooth Ring Scanner Guide
Barcodes in this guide must be printed on a 600dpi printer.
The barcodes cannot be scanned from a computer monitor.
Copyright © 2008 by LXE Inc.
All Rights Reserved
E-SW-BLUESCANPG-A

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the 8650 and is the answer not in the manual?

Questions and answers

Related Manuals for LXE 8650

Summary of Contents for LXE 8650

  • Page 1 Bluetooth Ring Scanner Guide Barcodes in this guide must be printed on a 600dpi printer. The barcodes cannot be scanned from a computer monitor. Copyright © 2008 by LXE Inc. All Rights Reserved E-SW-BLUESCANPG-A...
  • Page 2 Symbol® is a registered trademark of Symbol Technologies. MOTOROLA® and the Stylized M Logo are registered trademarks of Motorola®, Inc. The Bluetooth® word mark and logos are owned by the Bluetooth SIG, Inc. and any use of such marks by LXE, Inc. is under license.

  • Page 3: Table Of Contents

    HAPTER NTRODUCTION Barcodes, Ring Scanners and Scanner Engines ... 1 LXE Tethered Scanners and Mobile Bluetooth Scanners ... 2 Ring Decoder Warnings and Labels ... 3 Identify Your Ring Barcode Decoder Type... 4 Bluetooth Ring Scanner ... 5 Compatible Devices...5 Components ...6...
  • Page 4 Bluetooth Module Technical Specifications ... 26 Getting Help ... 27 Accessories ...27 HAPTER LUETOOTH ODULE Introduction... 29 Preparation... 29 LXE Programming Barcodes... 30 Restore Factory Defaults ...30 Module Firmware Version...30 Pairing Status ...31 Suspend Timeout...32 Beep on Reconnect ...34 Reconnect Interval Timeout...35 Reconnect Timeout...37 Role Switching...38...
  • Page 5 Disable ACK/NAK Handshaking ...94 Enable ACK/NAK Handshaking ...94 Stop Bit Select ...95 Transmit “No Read / Decode” Message ...96 Trigger Mode ...97 Scanner Parameters – SE955 Barcode Type Specific ... 99 Chinese 2 of 5...99 Codabar ...99 CLSI Editing...100 NOTIS Editing...100 Set Lengths for Codabar...101...
  • Page 6 Transmit UPC-A Check Digit...137 Transmit UPC-E Check Digit ...137 Transmit UPC-E1 Check Digit ...138 Conversions...139 Convert UPC-E to UPC-A...139 Convert UPC-E1 to UPC-A...139 Convert EAN-8 to EAN-13 Type ...140 Preambles...141 UPC-A Preamble ...141 UPC-E Preamble...142 Bluetooth Ring Scanner Guide Table of Contents E-SW-BLUESCANPG-A...
  • Page 7 Time-out between Decodes, Same Symbol ...183 Trigger Modes ...184 Report Version...185 Transmit Code ID Character...186 Transmit No Code ID Character ...186 Transmit Symbol Code ID Character...186 Transmit AIM Code ID Character ...187 Prefix / Suffix Values ...191 E-SW-BLUESCANPG-A Bluetooth Ring Scanner Guide...
  • Page 8 Code 11 Check Digit Verification...226 Transmit Code 11 Check Digits...227 Interleaved 2 of 5 (ITF) ... 228 Set Lengths for I 2 of 5...228 One Discrete Length (Parameter L1) ...229 Two Discrete Lengths (Parameter L2)...229 Bluetooth Ring Scanner Guide Table of Contents E-SW-BLUESCANPG-A...
  • Page 9 Composite CC-C ...254 Composite CC-A/B...254 Composite TLC-39...255 UPC Composite Mode ...256 UCC/EAN Code 128 Emulation Mode ...257 2D Symbologies... 258 PDF417...258 MicroPDF417 ...258 Code 128 Emulation...259 Data Matrix ...260 Data Matrix Inverse...260 Maxicode...261 QR Code...261 MicroQR ...262 E-SW-BLUESCANPG-A Bluetooth Ring Scanner Guide...
  • Page 10 Security Level ... 266 Intercharacter Gap Size ...268 Imager Keypad Number Symbols ... 269 HAPTER NGINE ECHNICAL Scanner Identification Label ... 271 Decode Zones ... 271 SE955-I000WR Standard Range Laser Scanner...272 SE4400 Laser Imager...273 Near Focus Decode Distances...273 PL4407 ...273 MS4407 ...273...
  • Page 11 Figure 1-3 Ring Imager (L) and Ring Scanner (R) ...4 Figure 1-4 Ring Imager (L) and Ring Scanner (R) Apertures...4 Figure 1-5 Bluetooth Ring Scanner Assembly – On the Wrist or Back of Hand ...5 Figure 1-6 Components - Module ...6 Figure 1-7 Components –...
  • Page 12 Table of Contents Bluetooth Ring Scanner Guide E-SW-BLUESCANPG-A...

  • Page 13: Chapter 1 Introduction

    Bluetooth® Ring Scanner and its tethered ring scanner and ring imager. LXE barcode decoding laser engines and barcode decoding imager engines are designed to read, decode and collect barcoded data from any nearby compatible barcode label that is visible and on printed media.

  • Page 14: Lxe Tethered Scanners And Mobile Bluetooth Scanners

    This guide does not include the barcodes to be used when programming tethered scanners connected to a COM port or serial port on LXE Bluetooth enabled mobile devices or their cradles/docks, the LXE 8300 and 8500 scanner series specifically, or Bluetooth mobile scanners /imagers with trigger handles.

  • Page 15: Ring Decoder Warnings And Labels

    • Do not look into the ring scanner/imager aperture. • Do not stare directly into the ring scanner/imager laser beam. • Do not remove the laser caution labels from the ring scanner/imager. • Do not connect the ring decoder aperture to any other device.

  • Page 16: Identify Your Ring Barcode Decoder Type

    Imagers and scanners use laser beams when scanning a barcode. • The ring scanner has an SE955 scan engine (see Chapter 3 for programming barcodes). • The ring imager has an SE4400 scan engine (see Chapter 4 for programming barcodes).

  • Page 17: Bluetooth Ring Scanner

    The scan engine manufacturer may offer more barcodes and parameter options than are contained in this guide. Please note that the barcodes in this guide are only those supported by LXE and the imagers or scanners linked to LXE mobile devices that LXE manufactures or supports. If you need assistance when using the barcodes in this guide, please contact your LXE representative.

  • Page 18: Components

    Bluetooth Module Note: The Bluetooth Module ring scanner and ring imager connectors are not interchangeable with the ring scanner and ring imager connectors designed for the HX2 or the HX3 mobile device. Bluetooth Ring Scanner Guide Figure 1-6 Components - Module...

  • Page 19: Ring Imager / Ring Scanner

    1D and 2D barcodes. The type of barcodes scanned successfully depends on the scan type of the tethered ring device. After pairing with an LXE mobile device, it can then send the collected barcode data to the specific Bluetooth enabled LXE mobile device for processing.

  • Page 20: Battery

    Bluetooth MAC ID Barcode Label Figure 1-10 Sample MX8 Bluetooth Address (MAC ID) Barcode Label Locate the barcode label, similar to the one shown above, attached to the LXE Bluetooth capable mobile device. It may be on any side of the device.

  • Page 21: Bluetooth Module Assembly

    Press the connector firmly into the I/O port until the Bluetooth module LED illuminates and the module beeps, signifying a ring cable I/O secure connection. To remove the ring scanner cable, pinch and pull the cable connector (not the cable!) straight up and away from the Bluetooth module.

  • Page 22: Adjusting The Ring Device Strap

    Do not use a metal object, or extreme force, to remove the battery from the module. If a ring scanner is tethered to the Bluetooth module while a battery is being hotswapped and there is no beep or LED flash, remove the battery, turn it over and reinsert, making sure the battery terminals enter the battery bay to the right.

  • Page 23: Assembled

    Introduction Assembled Worn on left hand, on back of hand Worn on right hand, on back of wrist Figure 1-11 Bluetooth Ring Scanner Assembled E-SW-BLUESCANPG-A Bluetooth Ring Scanner Guide...

  • Page 24: Status Led And Beep Indicators

    The ring devices do not have the ability to emit a good decode read sound (after a barcode scan) or bad decode read sound. The Bluetooth Ring Scanner module emits the good read or bad read sounds. The module and the ring devices have an LED.

  • Page 25: Bluetooth Module Status Led And Beep Indicators

    Short high tone beep Short low tone beep Short low tone beep Short high tone beep (When “Beep on Connect” is enabled. See LXE Programming Barcodes) Short high tone beep Short low tone beep (When “Beep on Connect” is enabled. See LXE...

  • Page 26: Bluetooth Ring Imager Led And Ring Scanner Led

    Bluetooth Ring Imager LED and Ring Scanner LED The ring decoding devices do not have the ability to emit a good read or bad read sound. The Ring Scanner indicates status as follows: Green Green Slow blink Amber, once every .25 sec.

  • Page 27: Bluetooth Module Reboot Sequences

    8 hours and remain in standby for approximately 24 hours. Battery Low When a battery low condition exists, LXE recommends the battery be hotswapped with a fully charged battery as soon as possible. The Ring Scanner Amber LED indicates a battery low condition by blinking for .25 seconds every 5 seconds until a Battery Dead condition occurs or the battery is replaced with a fully charged battery.

  • Page 28: Removing / Replacing The Trigger Module

    Do not touch, push on or brace your finger against the scan aperture at any time. LXE recommends that installation or removal of accessories be performed on a clean, well-lit surface. When necessary, protect the work surface, the mobile device, and components from electrostatic discharge.

  • Page 29: Replace

    This quick disconnect function is designed for occasional safety hazards and is not intended for daily removal. A 20 pak of Ring Scanner Finger Straps is available from LXE (8600A401RINGSTRAP). See Accessories. Using the Quick Disconnect Function, grasp the finger strap and pull the finger strap out and away from the ring scanner.

  • Page 30: Bluetooth Module Firmware Update

    “BlueCore Device Firmware Update Installation Instruction” in the “Appendix” in this guide for instruction. Bluetooth Module Firmware update cable (8650A051CBLBTUPDATE) Firmware update file (contact your LXE representative to obtain the latest Bluetooth Module firmware update file). A Bluetooth Module and a fully charged battery.

  • Page 31: Troubleshooting

    If the firmware update is interrupted due to loss of power or by removing the cable before the update is complete, the original firmware will be destroyed and the Bluetooth Ring Scanner will not be able to run in normal operation mode. If this event occurs the utility on the PC indicates that the firmware upgrade was not successful.

  • Page 32: How To

    Print the page on white paper using a 600dpi laser printer (or equivalent). LXE recommends printing the page containing the Reset and Cancel barcodes as well as the page containing the A – F and 0 – 9 number barcodes.

  • Page 33: Figure 1-17 Scanning A 2D Barcode

    Note: Whether there are beeps in conjunction with scan and decode functions is dependent on the application currently running in the LXE Bluetooth capable mobile device. Beeps are also emitted by the Bluetooth module, not the ring device. Note: Decrease decode time by disabling unused barcode types.

  • Page 34: Troubleshooting

    Ring decoding devices do not have the ability to emit a good read or bad read sound. Beep After Good Decode Audible scan progress indicators are generated by the scanner driver on LXE mobile devices (i.e. HX2), not the tethered ring decoder engine. Use the Windows CE Control Panel options to set up the mobile device audible indicators.

  • Page 35: Factors That May Impact Scanner Performance

    Code 39. The use of Code 128 or other more complex symbologies will almost always result in a reduction in maximum read distance. LXE will not support scanner maximum distances (from Decode Zones) when symbologies other than Code 39 are used.

  • Page 36: Pairing Bluetooth Devices

    Open the Bluetooth Devices panel. Tap the Discover button to discover nearby Bluetooth scanners and printers. Identify the scanner you wish to pair with by matching the Friendly name (LXE Scanner – [MAC ID]) with the MAC address label on the scanner. Doubletap the Friendly Name and select Pair as Scanner from the drop-down menu.

  • Page 37: Clear Paired Status

    Clear Paired Status Using the LXE Bluetooth device (e.g. handheld or vehicle mount unit) access the LXEZ Pairing control panel by tapping the Bluetooth icon on the Desktop (or the Taskbar or the Control Panel).

  • Page 38: Bluetooth Module Technical Specifications

    Corrosion Chemical Resistance Abrasion Resistance The CF Bluetooth Radio in the LXE Bluetooth Ring Scanner is Bluetooth Special Interest Group (SIG) Qualified, is listed as an EPL (End Product Listing) and with QDID: B011904. Bluetooth Ring Scanner Guide A 22 spring-pin, symmetrical port Without Scanner : Height 0.75”...

  • Page 39: Getting Help

    Introduction Getting Help LXE user and reference guides are now available on one CD and they can also be viewed and downloaded from the LXE website on the ServicePass or PartnerPass / Documentation page. Contact your LXE representative to obtain the LXE Manuals CD or logon information for the LXE website.
  • Page 40 Introduction Bluetooth Ring Scanner Guide E-SW-BLUESCANPG-A...

  • Page 41: Chapter 2 Bluetooth Module Programming Barcodes

    The scan engine manufacturer may offer more barcodes and options than are contained in this guide. Please note that the barcodes in this guide are only those supported by LXE and the imagers or scanners linked to LXE mobile devices that LXE manufactures or supports. If you need assistance when using the barcodes in this guide, please contact your LXE representative.

  • Page 42: Lxe Programming Barcodes

    Bluetooth Ring Scanner module is fully assembled (battery, ring decoder) and connected to a device with a video display. Scan this barcode, with either the ring scanner or the ring imager, to view the LXE firmware version of the Bluetooth Ring Scanner module on the host device display.

  • Page 43: Pairing Status

    See Also: Role Switching parameter. Troubleshooting The LnkB barcodes on some LXE Bluetooth capable mobile devices are quite small. If you are unsuccessful using the ring imager when scanning a LnkB barcode, change the ring imager’s default Smart Focus Mode to Near Focus by scanning the Enable Near Focus barcode in Chapter 4.

  • Page 44: Suspend Timeout

    Disable Suspend Timeout Set Suspend Timeout to 15 seconds Set Suspend Timeout to 30 seconds Set Suspend Timeout to 1 minute Set Suspend Timeout to 5 minutes Bluetooth Ring Scanner Guide Bluetooth Module Programming Barcodes 5 minutes E-SW-BLUESCANPG-A...
  • Page 45 Bluetooth Module Programming Barcodes Set Suspend Timeout 15 minutes Set Suspend Timeout to 30 minutes Set Suspend Timeout to 45 minutes Set Suspend Timeout to 60 minutes E-SW-BLUESCANPG-A Bluetooth Ring Scanner Guide...

  • Page 46: Beep On Reconnect

    1 second. Scan the Disable Beep on Reconnect to disable audible notification for connect and disconnect. See Also: Reconnect Interval Timeout. Enable Beep on Reconnect Disable Beep on Reconnect Bluetooth Ring Scanner Guide Bluetooth Module Programming Barcodes Enable E-SW-BLUESCANPG-A...

  • Page 47: Reconnect Interval Timeout

    Bluetooth enabled device. See Also: Beep on Reconnect Reconnect Interval Timeout 15 seconds Reconnect Interval Timeout 30 seconds Reconnect Interval Timeout 45 seconds Reconnect Interval Timeout 1 minutes Reconnect Interval Timeout 5 minutes E-SW-BLUESCANPG-A 30 seconds Bluetooth Ring Scanner Guide...
  • Page 48 Reconnect Interval Timeout 10 minutes Reconnect Interval Timeout 15 minutes Reconnect Interval Timeout 30 minutes Bluetooth Ring Scanner Guide Bluetooth Module Programming Barcodes E-SW-BLUESCANPG-A...

  • Page 49: Reconnect Timeout

    When the parameter is set to Off, reconnect attempts will continue until the battery in the Bluetooth module is depleted. See Also: Beep on Reconnect Reconnect Timeout Reconnect Timeout 1 minute Reconnect Timeout 5 minutes Reconnect Timeout 30 minutes E-SW-BLUESCANPG-A 1 minute Bluetooth Ring Scanner Guide...

  • Page 50: Role Switching

    Role Switching Parameter Default Value: When Role Switching is enabled and the module has successfully paired with an LXE Bluetooth capable mobile device (e.g. MX8) as a master, the module will perform role switching with the mobile device and become a slave device.

  • Page 51: Authentication

    Authentication is the process of verifying the identity of a device with which a connection is to be established. When Authentication is disabled, any device can connect to the Bluetooth Ring Scanner module. When Authentication is enabled, the connecting device is required to enter the PIN value set by the Bluetooth Ring Scanner module before successful connection can occur.

  • Page 52: Imager White Leds

    Disabling this parameter does not affect the scan beam or scan beam timer. Note: Enabling Imager White LEDs may reduce module battery life. Scan the appropriate barcode below: Enable Imager White LEDs Disable Imager White LEDs Bluetooth Ring Scanner Guide Bluetooth Module Programming Barcodes Disable E-SW-BLUESCANPG-A...

  • Page 53: Beep Volume

    Bluetooth Module Programming Barcodes Beep Volume Parameter Default Value: The Bluetooth Module speaker volume can be reset by scanning one of the following barcodes. Volume Off Volume Low Volume Medium Volume High E-SW-BLUESCANPG-A High Bluetooth Ring Scanner Guide...

  • Page 54: Ring Imager Focus Mode

    Ring Imager Focus Mode Note: This parameter is to be used for the ring imager connected to the Bluetooth Ring Scanner module only. The ring scanner will ignore this parameter if it scans it in error. Parameter Default Value: Select a focus mode to control the working range of the imager.

  • Page 55: Enter Friendly Name Or Pin Code

    The PIN Code default value is 16 zeros. To reset the Pin Code back to the default, scan the Set Pin Code barcode and the Pin Code Default barcode only. Set PIN Code Pin Code Default Stop PIN Code setup E-SW-BLUESCANPG-A Bluetooth Ring Scanner Guide...

  • Page 56: Friendly Name

    When finished entering all characters, scan the Stop Friendly Name setup barcode to end Friendly Name data entry. The Friendly Name default value is “LXE Scanner” + MAC address in Hexadecimal. The Friendly Name can be viewed using LXEZ Pairing on the paired LXE mobile device. Set Friendly Name Stop Friendly Name setup...

  • Page 57: Numbers

    Bluetooth Module Programming Barcodes Numbers Cancel current programming function E-SW-BLUESCANPG-A Bluetooth Ring Scanner Guide...
  • Page 58 Bluetooth Ring Scanner Guide Bluetooth Module Programming Barcodes E-SW-BLUESCANPG-A...

  • Page 59: Lowercase Letters

    Bluetooth Module Programming Barcodes Lowercase Letters Cancel current programming function E-SW-BLUESCANPG-A Bluetooth Ring Scanner Guide...
  • Page 60 Bluetooth Ring Scanner Guide Bluetooth Module Programming Barcodes E-SW-BLUESCANPG-A...
  • Page 61 Bluetooth Module Programming Barcodes E-SW-BLUESCANPG-A Bluetooth Ring Scanner Guide...
  • Page 62 Bluetooth Ring Scanner Guide Bluetooth Module Programming Barcodes E-SW-BLUESCANPG-A...
  • Page 63 Bluetooth Module Programming Barcodes E-SW-BLUESCANPG-A Bluetooth Ring Scanner Guide...
  • Page 64 Bluetooth Ring Scanner Guide Bluetooth Module Programming Barcodes E-SW-BLUESCANPG-A...

  • Page 65: Uppercase Letters

    Bluetooth Module Programming Barcodes Uppercase Letters Cancel current programming function E-SW-BLUESCANPG-A Bluetooth Ring Scanner Guide...
  • Page 66 Bluetooth Ring Scanner Guide Bluetooth Module Programming Barcodes E-SW-BLUESCANPG-A...
  • Page 67 Bluetooth Module Programming Barcodes E-SW-BLUESCANPG-A Bluetooth Ring Scanner Guide...
  • Page 68 Bluetooth Ring Scanner Guide Bluetooth Module Programming Barcodes E-SW-BLUESCANPG-A...
  • Page 69 Bluetooth Module Programming Barcodes E-SW-BLUESCANPG-A Bluetooth Ring Scanner Guide...
  • Page 70 Bluetooth Module Programming Barcodes Bluetooth Ring Scanner Guide E-SW-BLUESCANPG-A...

  • Page 71: Chapter 3 Se955 Laser Barcodes

    Chapter 3 SE955 Laser Barcodes This chapter’s explanations and instructions are directed toward Symbol SE955 laser scanner engines in Bluetooth Ring Scanners. DO NOT SCAN THE BARCODES IN THIS CHAPTER WITH ANY OTHER IMAGER / LASER ENGINE. Introduction To change a parameter value: The following barcode symbologies are supported: The tethered ring scanner does not have beep / audio capability.

  • Page 72: Aiming Modes

    Decoding algorithms released by the barcode engine manufacturer often change upon each new release. Programming parameters that were available at one release may not be available upon a later software release. LXE supports the programming barcodes for the specific engines in this guide only.

  • Page 73: Pre-Configured Default Values

    3.0 sec. Enable Low Power Not Supported Not Supported Not Supported Wide Not Supported Not Supported Not Supported Not Supported Disable Host Enable Enable Disable Enable Enable Disable Ignore Enable Enable Enable System Character System Character Bluetooth Ring Scanner Guide...
  • Page 74 Code 39 Decode Performance Level Code 93 Code 93 Set Length(s) for Code 93 Code 11 Code 11 Set Lengths for Code 11 Code 11 Check Digit Verification Bluetooth Ring Scanner Guide SE955 Laser Barcodes Default System Character Disable Disable Disable Type is EAN-13...
  • Page 75 Disable Disable Disable Disable Disable Disable Disable Length within Range: 05-55 Disable Length within Range: 06-55 Disable Mod 10/Mod 10 Not Supported Not Supported Not Supported Not Supported Disable Disable Disable Disable Not Supported Not Supported Bluetooth Ring Scanner Guide...
  • Page 76 Transmit Block Count Transmit Time Stamp Transmit Sender Transmit Addressee Transmit Checksum Transmit File Size Transmit Macro PDF Control Header Last Block Marker Bluetooth Ring Scanner Guide SE955 Laser Barcodes Default Not Supported None NULL Data as is Not Supported...

  • Page 77: Frequently Used Barcodes - Se955

    Restore Defaults If custom defaults were set by scanning Write Custom Defaults, scan Restore Defaults to retrieve and restore the scanner’s custom default settings. If no custom defaults were set, scan Restore Defaults to restore the factory default values. Set Factory Defaults Restore the factory default values.

  • Page 78: Configure The Decoder For Barcode Types

    Note: Improve decode speed by disabling unused barcode types. Bookland EAN Enable Bookland EAN Disable Bookland EAN Chinese 2 of 5 Enable Chinese 2 of 5 Disable Chinese 2 of 5 Bluetooth Ring Scanner Guide SE955 Laser Barcodes E-SW-BLUESCANPG-A...

  • Page 79: Codabar

    SE955 Laser Barcodes Codabar Enable Codabar Disable Codabar Code 11 Enable Code 11 Disable Code 11 Code 128 Enable Code 128 Disable Code 128 E-SW-BLUESCANPG-A Bluetooth Ring Scanner Guide...

  • Page 80: Code 39

    Trioptic Code 39 symbols always contain 6 characters. Trioptic Code and Code 39 Full ASCII should not be enabled simultaneously. Enable Trioptic Code 39 Disable Trioptic Code 39 Code 93 Enable Code 93 Disable Code 93 Bluetooth Ring Scanner Guide SE955 Laser Barcodes E-SW-BLUESCANPG-A...

  • Page 81: Discrete 2 Of 5

    SE955 Laser Barcodes Discrete 2 of 5 Enable Discrete 2 of 5 Disable Discrete 2 of 5 EAN-13 Enable EAN-13 Disable EAN-13 EAN-8 Enable EAN-8 Disable EAN-8 E-SW-BLUESCANPG-A Bluetooth Ring Scanner Guide...

  • Page 82: Interleaved 2 Of 5

    Interleaved 2 of 5 Enable Interleaved 2 of 5 Disable Interleaved 2 of 5 ISBT 128 Enable ISBT 128 Disable ISBT 128 MSI Plessey Enable MSI (Plessey) Disable MSI (Plessey) Bluetooth Ring Scanner Guide SE955 Laser Barcodes E-SW-BLUESCANPG-A...

  • Page 83: Ucc/Ean-128

    SE955 Laser Barcodes UCC/EAN-128 Enable UCC/EAN-128 Disable UCC/EAN-128 UPC-A Enable UPC-A Disable UPC-A UPC-E Enable UPC-E Disable UPC-E E-SW-BLUESCANPG-A Bluetooth Ring Scanner Guide...

  • Page 84: Upc-E1

    UPC-E1 Enable UPC-E1 Disable UPC-E1 Bluetooth Ring Scanner Guide SE955 Laser Barcodes E-SW-BLUESCANPG-A...

  • Page 85: Scanner Parameters - General

    For correct operation, reboot the mobile device after changing this value. When a scanner with an aim mode is triggered either by a Scan button press, or a Start_Decode command, this parameter sets the duration the aiming pattern is seen before a scan attempt begins.

  • Page 86: Bi-Directional Redundancy

    The default for Security Level parameter is Level 1. Select an option by scanning either of the barcodes shown below. If you wish to change your selection, scan Cancel. Enable Bi-Directional Redundancy Disable Bi-Directional Redundancy Cancel Bluetooth Ring Scanner Guide Disable E-SW-BLUESCANPG-A SE955 Laser Barcodes...

  • Page 87: Data Options

    SE955 Laser Barcodes Data Options SE955 scanner engine prefix and suffix parameters cannot be set, changed, or reset using the barcodes in this chapter. See previous section titled Prefix / Suffix. Prefix and Suffix Prefix (P) Parameter Default Value: Suffix1 (S1) Parameter Default Value:...

  • Page 88: Suffix 1

    Next, scan four numeric barcodes that correspond to the computer keycode using the “Keypad Number Symbols” at the end of this chapter. If you wish to change your numeric selection, scan Cancel on the “Keypad Number Symbols” page. Bluetooth Ring Scanner Guide SE955 Laser Barcodes E-SW-BLUESCANPG-A...

  • Page 89: Scan Data Transmission Format

    Use this option when you want to append a prefix and suffix to the decode data. Set this parameter by scanning one of the following barcodes. Data As Is [Data] [Suffix 1] [Data] [Suffix 2] [Data] [Suffix 1] [Suffix 2] [Prefix] [Data] [Prefix] [Data] [Suffix 1] E-SW-BLUESCANPG-A Data As Is Bluetooth Ring Scanner Guide...
  • Page 90 [Prefix] [Data] [Suffix 2] [Prefix] [Data] [Suffix 1] [Suffix 2] Cancel Now you are ready to scan one of the “Prefix/Suffix Values” barcodes. Bluetooth Ring Scanner Guide SE955 Laser Barcodes E-SW-BLUESCANPG-A...

  • Page 91: Transmit Code Id Character

    A code ID character identifies the code type of a scanned barcode. This may be useful when the scanner is decoding more than one code type. In addition to any single character prefix already selected, the code ID character is inserted between the prefix and the decoded symbol.

  • Page 92: Transmit Aim Code Id Character

    = Modifier Character The modifier character is the sum of the applicable option values based on the following table. Code Type Code 39 Trioptic Code 39 Code 128 Bluetooth Ring Scanner Guide Code 39 Code 128 UPC/EAN Codabar Code 93 Code 11...
  • Page 93 Five digit supplement data only EAN-8 data packet. Example: A UPC-A barcode 012345678905 is transmitted as ]E00012345678905 No options specified at this time. Always transmit 0. Example: A Bookland EAN barcode 123456789X is transmitted as ]X0123456789X Bluetooth Ring Scanner Guide...

  • Page 94: Laser On Time

    Number Symbols” at the end of this chapter. Times less than 1.0 second must have a leading zero. If you wish to change your number selection, scan Cancel on the “Keypad Number Symbols” page. Bluetooth Ring Scanner Guide 3.0 Seconds E-SW-BLUESCANPG-A...

  • Page 95: Linear Code Type Security Level (Redundancy Level)

    Parameter Default Value: Use this parameter to determine the security level appropriate for barcode quality. The security level indicates how many times the barcode must be successfully read by the scanner before being decoded. There are four security levels. Higher security levels are selected for decreasing levels of barcode quality.
  • Page 96 Linear Security Level 3 Level 4 Cancel Bluetooth Ring Scanner Guide Code types other than the following must be successfully read two times before being decoded. The following codes (Code 128 exception) must be read three times: MSI Plessey Length of 4 characters or less...

  • Page 97: Parameter Scanning

    SE955 Laser Barcodes Parameter Scanning Parameter Default Value: Use this parameter to decide whether scanner parameters can be set using the barcodes in this chapter. Note: When this parameter is disabled, scan the Set Defaults parameter barcode to enable parameter scanning.

  • Page 98: Power Mode

    Power Mode Note: LXE mobile devices are designed to be operated in Low Power Mode. LXE recommends leaving this value unchanged. Parameter Default Value: A parameter setting of Continuous On means the laser scanner will not power down until the mobile device is powered off.

  • Page 99: Scan Angle

    Once the parameter barcode is scanned, the Scan Angle setting is persistently stored. Select an option by scanning one of the barcodes shown below. Narrow Angle (35°) Wide Scan Angle Cancel E-SW-BLUESCANPG-A Bluetooth Ring Scanner Guide...

  • Page 100: Set Default Parameter

    Restore Defaults If custom defaults were set by scanning Write Custom Defaults, scan Restore Defaults to retrieve and restore the scanner’s custom default settings. If no custom defaults were set, scan Restore Defaults to restore the factory default values. Set Factory Defaults Restore the factory default values.

  • Page 101: Simple Serial Interface (Ssi) Options

    SE955 Laser Barcodes Simple Serial Interface (SSI) Options Note: The following barcodes are directed toward the host programmer when writing host/scanner interface programs for different hosts. Contact LXE Customer Service for further assistance. Default Values: Option Baud Rate Beep on <BEL>...

  • Page 102: Decode Data Packet Format

    If the raw format is chosen, ACK/NAK handshaking is automatically disabled for decode data. Set this parameter by scanning either of the following barcodes. Send Raw Decode Data Send Packeted Decode Data Bluetooth Ring Scanner Guide SE955 Laser Barcodes E-SW-BLUESCANPG-A...

  • Page 103: Host Character Time-Out

    300 msec is selected by scanning the “3” and the “0” numeric barcodes. A value of 30 msec is selected by scanning the “0” and the “3” barcodes. If you wish to change your selection, scan Cancel on the “Keypad Number Symbols” page. E-SW-BLUESCANPG-A 200 msec Bluetooth Ring Scanner Guide...

  • Page 104: Host Serial Response Time-Out

    25 msec is selected by scanning the “2” and the “5” numeric barcodes. A value of 6 msec is selected by scanning the “0” and the “6” barcodes. If you wish to change your selection, scan Cancel on the “Keypad Number Symbols” page. Bluetooth Ring Scanner Guide SE955 Laser Barcodes 2 sec...

  • Page 105: Parity

    1 bits is contained in the coded character. Mark Parity The parity bit is always 1. Space Parity The parity bit is always 0. No Parity No parity is required. Cancel E-SW-BLUESCANPG-A None Bluetooth Ring Scanner Guide...

  • Page 106: Software Handshaking

    The scanner waits up to the programmable Host Serial Response Time-out to receive an ACK or NAK. If the scanner does not get a response in this time, it resends its data up to two times before discarding the data and declaring a transmit error.

  • Page 107: Stop Bit Select

    The number of stop bits selected (one or two) depends on the number the receiving computer is programmed to accommodate. Set the number of stop bits to match host device requirements. Set this parameter by scanning one of the following barcodes. One Stop Bit Two Stop Bits E-SW-BLUESCANPG-A Bluetooth Ring Scanner Guide...

  • Page 108: Transmit "No Read / Decode" Message

    When disabled, and a symbol does not decode, no message is sent to the host. Select an option by scanning either of the barcodes shown below. If you wish to change your selection, scan Cancel. Enable No Read Disable No Read Cancel Bluetooth Ring Scanner Guide Disable E-SW-BLUESCANPG-A SE955 Laser Barcodes...

  • Page 109: Trigger Mode

    SE955 Laser Barcodes Trigger Mode Note: LXE mobile devices with linked scanners are designed to be operated in Host Trigger Mode. LXE recommends leaving the Trigger Mode default value unchanged. Parameter Default Value: Use this parameter to determine when the laser is activated and decoding begins, how long the laser remains on and what determines the cessation of the laser scan and decode process.
  • Page 110 Host Triggering signal comes from a host command. Any actual Scan button press will be interpreted by the scanner engine as a Level triggering option. Cancel Bluetooth Ring Scanner Guide SE955 Laser Barcodes E-SW-BLUESCANPG-A...

  • Page 111: Scanner Parameters - Se955 Barcode Type Specific

    SE955 Laser Barcodes Scanner Parameters – SE955 Barcode Type Specific Chinese 2 of 5 Parameter Default Value: When enabled, Chinese 2 of 5 symbols will be scanned, decoded and transmitted. Set this parameter by scanning either of the barcodes shown below.

  • Page 112: Clsi Editing

    When enabled, the start and stop characters are stripped from a decoded Codabar symbol. Set this parameter by scanning either of the barcodes shown below. Enable NOTIS Editing Disable NOTIS Editing Bluetooth Ring Scanner Guide Disable characters of a 14 character Codabar symbol. Disable...

  • Page 113: Set Lengths For Codabar

    Next, scan two numeric barcodes that correspond to the desired value. Single digit numbers must have a leading zero. If you wish to change your number selection, scan Cancel on the “Keypad Number Symbols” page. E-SW-BLUESCANPG-A Bluetooth Ring Scanner Guide...

  • Page 114: Two Discrete Lengths (Parameter L2)

    Symbols” at the end of this chapter. Single digit numbers must have a leading zero. If you wish to change your number selection, scan Cancel on the “Keypad Number Symbols” page. Any Length This option decodes Codabar barcodes containing any number of characters. To set any length, scan this barcode: Bluetooth Ring Scanner Guide SE955 Laser Barcodes E-SW-BLUESCANPG-A...

  • Page 115: Code 11

    The length of a code refers to the number of characters, including check digits, the code contains. It also includes any start or stop characters. See the table titled “ASCII Character Equivalents” at the end of the “Appendix”. E-SW-BLUESCANPG-A Disable Bluetooth Ring Scanner Guide...

  • Page 116: One Discrete Length (Parameter L1)

    Next, scan numeric barcodes that correspond to the desired value using the “Keypad Number Symbols” at the end of this chapter. Single digit numbers must have a leading zero. If you wish to change your number selection, scan Cancel on the “Keypad Number Symbols” page. Bluetooth Ring Scanner Guide SE955 Laser Barcodes E-SW-BLUESCANPG-A...

  • Page 117: Any Length

    Enable “Code 11 Check Digit Verification” when “Transmit Code 11 Check Digits” is enabled. Set this parameter by scanning one of the barcodes shown below. Disable this feature One Check Digit Two Check Digits E-SW-BLUESCANPG-A Disable Bluetooth Ring Scanner Guide...

  • Page 118: Transmit Code 11 Check Digits

    Transmit Code 11 Check Digits Parameter Default Value: Note: Code 11 Check Digit Verification must be enabled for this parameter to function. Transmit (Enable) Do Not Transmit (Disable) Bluetooth Ring Scanner Guide Do Not Transmit (Disable) E-SW-BLUESCANPG-A SE955 Laser Barcodes...

  • Page 119: Code 128

    When AIM symbology identifiers are transmitted, the modifier character indicates the position of the leading FNC1 character according to AIM guidelines. For example, ]cl indicates a UCC/EAN- 128 symbol with a leading FNC1 character. E-SW-BLUESCANPG-A Enable Enable Bluetooth Ring Scanner Guide...
  • Page 120 EAN-128 convention. Standard Code 128 and UCC/EAN-128 may be mixed in an application. The scanner autodiscriminates between these symbols, and can enable or disable one or both code types via barcode menus. The following table indicates the behavior of the scanner in each of the four possible parameter settings.

  • Page 121: Isbt-128

    Parameter Default Value: Set this parameter by scanning either of the barcodes shown below. Enable ISBT-128 Disable ISBT-128 Lengths for Code 128 No length setting is required for Code 128. The default setting is Any Length. E-SW-BLUESCANPG-A Enable Bluetooth Ring Scanner Guide...

  • Page 122: Code 39

    Only those Code 39 symbols which include a modulo 43 check digit are decoded when this parameter is enabled. Set this parameter by scanning either of the barcodes shown below. Enable Code 39 Check Digit Verification Disable Code 39 Check Digit Verification Bluetooth Ring Scanner Guide Enable Disable E-SW-BLUESCANPG-A SE955 Laser Barcodes...

  • Page 123: Code 32 Prefix

    (Italian Pharma Code) parameter must also be enabled. Set this parameter by scanning either of the barcodes shown below. Enable Convert Code 39 to Code 32 Disable Convert Code 39 to Code 32 E-SW-BLUESCANPG-A Disable Disable Bluetooth Ring Scanner Guide...

  • Page 124: Code 39 Full Ascii Conversion

    See the table titled “ASCII Character Equivalents” at the end of the “Appendix”. Set this parameter by scanning either of the barcodes shown below. Enable Code 39 Full ASCII Conversion Disable Code 39 Full ASCII Conversion Bluetooth Ring Scanner Guide Disable E-SW-BLUESCANPG-A SE955 Laser Barcodes...

  • Page 125: Set Lengths For Code 39

    Next, scan two numeric barcodes that correspond to the desired value. Single digit numbers must have a leading zero. If you wish to change your number selection, scan Cancel on the “Keypad Number Symbols” page. E-SW-BLUESCANPG-A Bluetooth Ring Scanner Guide...

  • Page 126: Two Discrete Lengths (Parameter L2)

    If you wish to change your number selection, scan Cancel on the “Keypad Number Symbols” page. Any Length This option decodes Code 39 barcodes containing any number of characters. To set any length, scan this barcode: Bluetooth Ring Scanner Guide SE955 Laser Barcodes E-SW-BLUESCANPG-A...

  • Page 127: Transmit Code 39 Check Digit

    Parameter setting for “Code 39 Check Digit Verification” has no effect on this parameter value. Set this parameter by scanning either of the barcodes shown below. Enable Transmit Code 39 Check Digit Disable Transmit E-SW-BLUESCANPG-A Disable Bluetooth Ring Scanner Guide...

  • Page 128: Trioptic Code 39

    When Trioptic Code 39 is enabled, set the “Code 39 Full ASCII” parameter to disabled. Both parameters should not be enabled simultaneously. Set this parameter by scanning either of the barcodes shown below. Enable Trioptic Code 39 Disable Trioptic Code 39 Bluetooth Ring Scanner Guide Disable E-SW-BLUESCANPG-A SE955 Laser Barcodes...

  • Page 129: Code 93

    The length of a code refers to the number of characters, including check digits, the code contains. See the table titled “ASCII Character Equivalents” at the end of the “Appendix”. E-SW-BLUESCANPG-A Disable Bluetooth Ring Scanner Guide...

  • Page 130: One Discrete Length (Parameter L1)

    Next, scan four numeric barcodes that correspond to the desired value. Single digit numbers must have a leading zero. If you wish to change your number selection, scan Cancel on the “Keypad Number Symbols” page. Bluetooth Ring Scanner Guide SE955 Laser Barcodes E-SW-BLUESCANPG-A...

  • Page 131: Length Within Range

    If you wish to change your number selection, scan Cancel on the “Keypad Number Symbols” page. Any Length This option decodes Code 93 barcodes containing any number of characters. To set any length, scan this barcode: E-SW-BLUESCANPG-A Bluetooth Ring Scanner Guide...

  • Page 132: Discrete 2 Of 5

    When enabled, Discrete 2 of 5 (D 2 of 5) symbols will be scanned, decoded and transmitted. Set this parameter by scanning either of the barcodes shown below. Enable Discrete 2 of 5 Disable Discrete 2 of 5 Bluetooth Ring Scanner Guide Disable E-SW-BLUESCANPG-A SE955 Laser Barcodes...

  • Page 133: Set Lengths For Discrete 2 Of 5

    Next, scan four numeric barcodes that correspond to the desired value. Single digit numbers must have a leading zero. If you wish to change your number selection, scan Cancel on the “Keypad Number Symbols” page. E-SW-BLUESCANPG-A 1 Discrete Length: 12 Bluetooth Ring Scanner Guide...

  • Page 134: Length Within Range

    This option decodes D 2 of 5 barcodes containing any number of characters. Note: Selecting this option may lead to misdecodes for D 2 of 5 codes. To set any length, scan this barcode: Bluetooth Ring Scanner Guide SE955 Laser Barcodes E-SW-BLUESCANPG-A...

  • Page 135: Interleaved 2 Of 5

    When enabled, Interleaved 2 of 5 (I 2 of 5) symbols will be scanned, decoded and transmitted. Set this parameter by scanning either of the barcodes shown below. Enable Interleaved 2 of 5 Disable Interleaved 2 of 5 E-SW-BLUESCANPG-A Enable Bluetooth Ring Scanner Guide...

  • Page 136: I 2 Of 5 Digit Verification

    USS (Uniform Symbology Specification) or OPCC (Optical Product Code Council). Set this parameter by scanning one of the barcodes shown below. Disable I 2 of 5 Check Digit Verification USS Check Digit OPCC Check Digit Cancel Bluetooth Ring Scanner Guide Disable E-SW-BLUESCANPG-A SE955 Laser Barcodes...

  • Page 137: Convert I 2 Of 5 To Ean-13

    When enabled, the parameter converts a 14 character I 2 of 5 barcode into EAN-13 and transmits it to the host as EAN-13. Set this parameter by scanning either of the barcodes shown below. Enable Convert I 2 of 5 to EAN-13 Disable Convert I 2 of 5 to EAN-13 E-SW-BLUESCANPG-A Disable Bluetooth Ring Scanner Guide...

  • Page 138: Set Lengths For I 2 Of 5

    Next, scan two numeric barcodes that correspond to the desired value. Single digit numbers must have a leading zero. If you wish to change your number selection, scan Cancel on the “Keypad Number Symbols” page. Bluetooth Ring Scanner Guide E-SW-BLUESCANPG-A SE955 Laser Barcodes...

  • Page 139: Two Discrete Lengths (Parameter L2)

    To begin setting lengths within a range, scan this barcode: Next, scan numeric barcodes that correspond to the desired value. Single digit numbers must have a leading zero. If you wish to change your number selection, scan Cancel on the “Keypad Number Symbols” page. E-SW-BLUESCANPG-A Bluetooth Ring Scanner Guide...

  • Page 140: Any Length

    Parameter setting for “I 2 of 5 Check Digit Verification” has no effect on this parameter value. Set this parameter by scanning either of the barcodes shown below. Enable Transmit I 2 of 5 Check Digit Disable Transmit I 2 of 5 Check Digit Bluetooth Ring Scanner Guide Disable E-SW-BLUESCANPG-A SE955 Laser Barcodes...

  • Page 141: Msi Plessey

    When the “Two MSI Plessey Check Digits” option is selected, an additional verification is required to ensure integrity. Either of the two following algorithms may be selected. Set this parameter by scanning either of the algorithm barcodes shown below. Mod 10/Mod 11 Mod 10/Mod 10 E-SW-BLUESCANPG-A Disable Mod10/Mod10 Bluetooth Ring Scanner Guide...

  • Page 142: Msi Plessey Check Digits

    Set the number of check digits to be included with the barcode by scanning either of the barcodes shown below. One MSI Plessey check digit Two MSI Plessey check digits Bluetooth Ring Scanner Guide E-SW-BLUESCANPG-A SE955 Laser Barcodes...

  • Page 143: Set Lengths For Msi Plessey

    Next, scan four numeric barcodes that correspond to the desired value. Single digit numbers must have a leading zero. If you wish to change your number selection, scan Cancel on the “Keypad Number Symbols” page. E-SW-BLUESCANPG-A Bluetooth Ring Scanner Guide...

  • Page 144: Length Within Range

    Any Length This option decodes MSI Plessey barcodes containing any number of characters. Note: Selecting this option may lead to misdecodes for MSI Plessey codes. To set any length, scan this barcode: Bluetooth Ring Scanner Guide SE955 Laser Barcodes E-SW-BLUESCANPG-A...

  • Page 145: Transmit Msi Plessey Check Digit

    Parameter Default Value: When enabled, the check digit is transmitted with the data. Set this parameter by scanning either of the barcodes shown below. Enable Transmit MSI Plessey Check Digit Disable Transmit MSI Plessey Check Digit E-SW-BLUESCANPG-A Disable Bluetooth Ring Scanner Guide...

  • Page 146: Upc/Ean

    Select an option by scanning either of the barcodes shown below. Enable UPC-A Disable UPC-A UPC-E Parameter Default Value: Select an option by scanning either of the barcodes shown below. Enable Disable Bluetooth Ring Scanner Guide Enable Enable E-SW-BLUESCANPG-A SE955 Laser Barcodes...

  • Page 147: Upc-E1

    Select an option by scanning either of the barcodes shown below. Enable UPC-E1 Disable UPC-E1 EAN-8 Parameter Default Value: Select an option by scanning either of the barcodes shown below. Enable EAN-8 Disable EAN-8 E-SW-BLUESCANPG-A Disable Enable Bluetooth Ring Scanner Guide...

  • Page 148: Ean-13

    Select an option by scanning either of the barcodes shown below. Enable EAN-13 Disable EAN-13 Bookland EAN Parameter Default Value: Select an option by scanning either of the barcodes shown below. Enable Bookland EAN Disable Bookland EAN Bluetooth Ring Scanner Guide Enable Disable E-SW-BLUESCANPG-A SE955 Laser Barcodes...

  • Page 149: Check Digits

    This parameter determines whether the symbol will be transmitted with or without the UPC-E check digit. Select an option by scanning either of the barcodes shown below. Enable Transmit UPC-E Check Digit Disable Transmit UPC-E Check Digit E-SW-BLUESCANPG-A Enable Enable Bluetooth Ring Scanner Guide...

  • Page 150: Transmit Upc-E1 Check Digit

    This parameter determines whether the symbol will be transmitted with or without the UPC-E1 check digit. Select an option by scanning either of the barcodes shown below. Enable Transmit UPC-E1 Check Digit Disable Transmit UPC-E1 Check Digit Bluetooth Ring Scanner Guide Enable E-SW-BLUESCANPG-A SE955 Laser Barcodes...

  • Page 151: Conversions

    A programming selections (e.g. Preamble, Check Digit, etc.). When disabled, UPC-E1 (zero suppressed) decoded data is transmitted without conversion. Select an option by scanning either of the barcodes shown below. Enable UPC-E1 to UPC-A conversion Disable UPC-E1 to UPC-A conversion E-SW-BLUESCANPG-A Disable Disable Bluetooth Ring Scanner Guide...

  • Page 152: Convert Ean-8 To Ean-13 Type

    When “EAN-8 Zero Extend” is disabled, this parameter’s conversion setting is ignored. Select an option by scanning either of the barcodes shown below. Type is EAN-13 Type is EAN-8 Bluetooth Ring Scanner Guide Type is EAN-13 E-SW-BLUESCANPG-A SE955 Laser Barcodes...

  • Page 153: Preambles

    Select an option by scanning one of the barcodes shown below. No UPC-A Preamble <DATA> System Character <SYSTEM CHARACTER><DATA> System Character and Country Code (“0” for USA) <COUNTRY CODE> <SYSTEM CHARACTER> <DATA> E-SW-BLUESCANPG-A System Character [data] [schar] [data] [country code] [schar] [data] Bluetooth Ring Scanner Guide...

  • Page 154: Upc-E Preamble

    Select an option by scanning one of the barcodes shown below. No UPC-E Preamble <DATA> System Character <SYSTEM CHARACTER><DATA> System Character and Country Code (“0” for USA) <COUNTRY CODE> <SYSTEM CHARACTER> <DATA> Bluetooth Ring Scanner Guide System Character [data] [schar] [data] [country code] [schar] [data] E-SW-BLUESCANPG-A SE955 Laser Barcodes...

  • Page 155: Upc-E1 Preamble

    Select an option by scanning one of the barcodes shown below. No UPC-E1 Preamble <DATA> System Character <SYSTEM CHARACTER><DATA> System Character and Country Code (“0” for USA) <COUNTRY CODE> <SYSTEM CHARACTER> <DATA> E-SW-BLUESCANPG-A System Character [data] [schar] [data] [country code] [schar] [data] Bluetooth Ring Scanner Guide...

  • Page 156: Supplementals

    Supplementals Ignore UPC/EAN with Supplementals Autodiscriminate UPC/EAN Supplementals Bluetooth Ring Scanner Guide Ignore UPC/EAN symbols without supplemental characters are not decoded. When a UPC/EAN plus supplemental symbol is scanned, the UPC/EAN is decoded and the supplemental characters ignored. When this option is selected you must assign a value to the “Decode UPC/EAN Supplemental Redundancy”...
  • Page 157 Supplemental Mode Enable Smart Supplemental Mode E-SW-BLUESCANPG-A The scanner will identify supplementals for EAN-13 barcodes that start with a 378 or 379 prefix only. All other UPC/EAN codes are decoded immediately and the supplemental characters ignored. The scanner will identify supplementals for EAN-13 barcodes that start with a 978 prefix only.

  • Page 158: Decode Upc/Ean Supplemental Redundancy

    When disabled, EAN-8 symbols are transmitted as is and parameter “Convert EAN-8 to EAN-13 Type” setting is ignored. Select an option by scanning either of the barcodes shown below. Enable EAN-8 Zero Extend Disable EAN-8 Zero Extend Bluetooth Ring Scanner Guide 7 Times Disable E-SW-BLUESCANPG-A SE955 Laser Barcodes...

  • Page 159: Ucc Coupon Extended Code

    The UCC Coupon Extended Code is an additional barcode adjacent to a UCC Coupon Code. To enable or disable UCC Coupon Extended Code, scan the appropriate barcode below. Enable UCC Coupon Extended Code Disable UCC Coupon Extended Code E-SW-BLUESCANPG-A Disable Bluetooth Ring Scanner Guide...

  • Page 160: Upc/Ean Security Level

    Parameter Default Value: Use this parameter to determine the security level appropriate for UPC/EAN barcode quality. There is an inverse relationship between security and scanner aggressiveness, so be sure to choose only that level of security necessary for any given application.
  • Page 161 This level significantly impairs the decoding ability of the scanner. If this level of security is necessary, you should try to improve the quality of your barcodes. Bluetooth Ring Scanner Guide...

  • Page 162: Gs1 Databar (Rss) Codes

    Enable GS1 DataBar Limited (RSS Limited) Disable GS1 DataBar Limited (RSS Limited) GS1 DataBar Expanded (RSS Expanded) Enable GS1 DataBar Expanded (RSS Expanded) Disable GS1 DataBar Expanded (RSS Expanded) Bluetooth Ring Scanner Guide All Parameters : Disable E-SW-BLUESCANPG-A SE955 Laser Barcodes...

  • Page 163: Convert Gs1 Databar (Rss) To Upc/Ean

    Note that neither the system character nor the check digit can be stripped. Enable Convert GS1 DataBar (RSS) to UPC/EAN Disable Convert GS1 DataBar (RSS) to UPC/EAN E-SW-BLUESCANPG-A Disable Bluetooth Ring Scanner Guide...

  • Page 164: Keypad Number Symbols

    The barcode labels shown below represent a numeric keypad, with decimal values 0 through 9. Each label can be scanned individually to enter a numeric value. Use these numeric value symbols to enter numeric input in the course of performing a scan engine system configuration. Bluetooth Ring Scanner Guide SE955 Laser Barcodes E-SW-BLUESCANPG-A...
  • Page 165 SE955 Laser Barcodes Cancel E-SW-BLUESCANPG-A Bluetooth Ring Scanner Guide...
  • Page 166 SE955 Laser Barcodes Bluetooth Ring Scanner Guide E-SW-BLUESCANPG-A...

  • Page 167: C Hapter 4 Se4400 I Mager B Arcodes

    Scan engine manufacturers may offer more barcodes and options than are contained in this chapter. Please note that the barcodes in this chapter are only those supported by LXE and the mobile devices it manufactures or supports. If you need assistance when using the barcodes in this chapter, please contact your LXE representative.

  • Page 168: Imager Identification Label

    Imager Identification Label Look on the labels on your LXE Bluetooth Ring Scanner Module or the ring finger strap. The type of installed scan engine should be clearly labeled. Contact your system administrator or LXE Customer Service for assistance. Prefix / Suffix SE4400 prefix and suffix parameters cannot be set, changed, or reset using the barcodes in this chapter.

  • Page 169: Pre-Configured Default Values

    Far Focus Enable Enable Enable Internal LED Illumination External LED Illumination Not Supported Not Supported Data As Is Disable None Not Supported Not Supported Not Supported Enable Enable Disable Enable Enable Disable Ignore Enable Enable Enable Bluetooth Ring Scanner Guide...
  • Page 170 Transmit MSI Check Digit MSI Check Digit Algorithm Postal Codes 4State Postal US Postnet US Planet UK Postal Transmit UK Postal Check Digit Bluetooth Ring Scanner Guide SE4400 Imager Barcodes System Character System Character System Character Disable Disable Disable Disable...
  • Page 171 Disable Disable Disable Disable Not Supported Not Supported Disable Enable Disable Disable Enable Regular Only Enable Enable Enable Regular Only Enable Regular Only Normal Not Supported Not Supported Not Supported Not Supported Not Supported Not Supported Bluetooth Ring Scanner Guide...

  • Page 172: Frequently Used Barcodes – Se4400

    Set All Defaults barcode. Default value of Parameter Scanning is Enable. When parameters are changed, the new value replaces the standard default value in memory. Note: After scanning Set All Defaults barcode, reboot the Bluetooth Ring Scanner Module by removing the battery then reinserting the battery. Set All Defaults Cancel See “Pre-Configured Default Values”...

  • Page 173: Enable / Disable Parameter Scanning

    SE4400 Imager Barcodes Enable / Disable Parameter Scanning Parameter Default Value: Use this parameter to decide whether scanner parameters can be set using the barcodes in this chapter. Note: When this parameter is disabled, scan the Set All Defaults parameter barcode to enable parameter scanning.

  • Page 174: Configure Imager For Barcode Types

    Increase decode time by disabling unused barcode types. 2D Symbologies Refer to this symbology’s section later in this chapter for more programming barcodes. PDF417 Enable PDF417 Disable PDF417 MicroPDF417 Enable MicroPDF417 Disable MicroPDF417 Bluetooth Ring Scanner Guide SE4400 Imager Barcodes E-SW-BLUESCANPG-A...
  • Page 175 SE4400 Imager Barcodes Code 128 Emulation Enable Code 128 Emulation Disable Code 128 Emulation Data Matrix Enable Data Matrix Disable Data Matrix Maxicode Enable Maxicode Disable Maxicode E-SW-BLUESCANPG-A Bluetooth Ring Scanner Guide...

  • Page 176: Codabar

    Refer to this symbology’s main section later in this chapter for more programming barcodes. Disable Codabar Enable Codabar Code 11 Refer to this symbology’s main section later in this chapter for more programming barcodes. Enable Code 11 Disable Code 11 Bluetooth Ring Scanner Guide SE4400 Imager Barcodes E-SW-BLUESCANPG-A...
  • Page 177 Refer to this symbology’s main section later in this chapter for more programming barcodes. Enable Code 39 Disable Code 39 Code 93 Refer to this symbology’s main section later in this chapter for more programming barcodes. Enable Code 93 Disable Code 93 E-SW-BLUESCANPG-A Bluetooth Ring Scanner Guide...

  • Page 178: Composite

    Refer to this symbology’s main section later in this chapter for more programming barcodes. Enable Code 128 Disable Code 128 Composite Refer to this symbology’s section later in this chapter for more programming barcodes. Composite CC-C Enable Composite CC-C Disable Composite CC-C Bluetooth Ring Scanner Guide SE4400 Imager Barcodes E-SW-BLUESCANPG-A...

  • Page 179: Interleaved 2 Of 5

    Composite TLC-39 Enable Composite TLC-39 Disable Composite TLC-39 Interleaved 2 of 5 Refer to this symbology’s main section later in this chapter for more programming barcodes. Enable Interleaved 2 of 5 Disable Interleaved 2 of 5 E-SW-BLUESCANPG-A Bluetooth Ring Scanner Guide...

  • Page 180: Discrete 2 Of

    Refer to this symbology’s main section later in this chapter for more programming barcodes. Enable Discrete 2 of 5 Disable Discrete 2 of 5 ISBT-128 Refer to this symbology’s main section later in this chapter for more programming barcodes. Enable ISBT-128 Disable ISBT-128 Bluetooth Ring Scanner Guide SE4400 Imager Barcodes E-SW-BLUESCANPG-A...

  • Page 181: Msi (Plessey Code)

    Refer to this symbology’s main section later in this chapter for more programming barcodes. Enable MSI Disable MSI Postal Codes Refer to this symbology category’s section later in this chapter for more programming barcodes. US Postnet Enable US Postnet Disable US Postnet E-SW-BLUESCANPG-A Bluetooth Ring Scanner Guide...
  • Page 182 US Planet Enable US Planet Disable US Planet UK Postal Enable UK Postal Disable UK Postal Japan Postal Enable Japan Postal Disable Japan Postal Bluetooth Ring Scanner Guide SE4400 Imager Barcodes E-SW-BLUESCANPG-A...

  • Page 183: Gs1 Databar (Rss)

    Dutch Postal Enable Dutch Postal Disable Dutch Postal GS1 DataBar (RSS) Refer to this symbology’s main section later in this chapter for more programming barcodes. Enable GS1 DataBar Omnidirectional (RSS-14) Disable GS1 DataBar Omnidirectional (RSS-14) E-SW-BLUESCANPG-A Bluetooth Ring Scanner Guide...

  • Page 184: Upc/Ean

    UPC/EAN Refer to this symbology’s main section later in this chapter for more programming barcodes. UPC-A Enable UPC-A Disable UPC-A UPC-E Enable UPC-E Disable UPC-E UPC-E1 Enable UPC-E1 Disable UPC-E1 Bluetooth Ring Scanner Guide SE4400 Imager Barcodes E-SW-BLUESCANPG-A...
  • Page 185 SE4400 Imager Barcodes EAN-8/JAN-8 Enable EAN-8/JAN-8 Disable EAN-8/JAN-8 EAN-13/JAN-13 Enable EAN-13/JAN-13 Disable EAN-13/JAN-13 Bookland EAN Enable Bookland EAN Disable Bookland EAN E-SW-BLUESCANPG-A Bluetooth Ring Scanner Guide...

  • Page 186: Imager Parameters – General

    Except for the General imager attributes in this section that can be set by the end-user, imager programming attributes are set using the CE Control Panel Scanner panel resident on the mobile device. Barcode manipulation parameters assigned using the Control Panel Scanner panels are applied to the data resulting from successful barcode scans.

  • Page 187: Decode Aiming Pattern

    Select Disable Autoexposure to manually adjust the gain and exposure time (not supported in this version). This option is only recommended for advanced users with difficult image capture situations. Enable Decoding Autoexposure Disable Decoding Autoexposure E-SW-BLUESCANPG-A Enable Enable Bluetooth Ring Scanner Guide...

  • Page 188: Decoding Illumination

    Disable this parameter to prevent LED illumination. See LED Illumination. Select a setting by scanning one of the barcodes shown below. If you wish to change your selection, scan Cancel. Enable Illumination Disable Illumination Cancel Bluetooth Ring Scanner Guide SE4400 Imager Barcodes Enable Decoding Illumination E-SW-BLUESCANPG-A...

  • Page 189: Focus Mode

    • With Near Focus, the imager is optimized to read at its near position. • Smart Focus toggles the focus position after every frame. Scan the appropriate barcode below. Far Focus Near Focus Smart Focus E-SW-BLUESCANPG-A Far Focus Bluetooth Ring Scanner Guide...

  • Page 190: Led Illumination

    Select an illumination setting by scanning one of the barcodes shown below. If you wish to change your selection, scan Cancel. Internal Illumination External Illumination Internal and External Illumination Cancel Bluetooth Ring Scanner Guide SE4400 Imager Barcodes PL4407: Internal Illumination MS4407: External Illumination E-SW-BLUESCANPG-A...

  • Page 191: Operational Mode

    Decode Mode. Note: A Decode Mode barcode is not available. The default is that when the trigger is released, in other modes, the imager returns to Decode Mode. Snapshot Mode Video Mode Cancel E-SW-BLUESCANPG-A Decode Mode Bluetooth Ring Scanner Guide...

  • Page 192: Power Mode

    Power Mode Note: LXE mobile devices are designed to be operated in Low Power Mode. LXE recommends leaving this value unchanged. Parameter Default Value: A parameter setting of Continuous On means the laser will not power down until the mobile device is powered off.

  • Page 193: Presentation Mode Session Timeout

    For example, to set 0.5 seconds, scan the Presentation Mode Session Timeout barcode, then scan the 0, 0, 5 barcodes from the section titled Imager Keypad Number Symbols. To correct an error or change the selection, scan the Cancel barcode and try again. E-SW-BLUESCANPG-A 2 Seconds Bluetooth Ring Scanner Guide...

  • Page 194: Time Delay To Low Power Mode

    This parameter only applies when Power Mode is set to Low Power. See Power Mode. 1 Second Delay 5 Second Delay 1 Minute Delay 5 Minute Delay 15 Minute Delay Bluetooth Ring Scanner Guide SE4400 Imager Barcodes 1 Second E-SW-BLUESCANPG-A...

  • Page 195: Time-Out Between Decodes, Same Symbol

    0.1 second increments. Times less than 1.0 second must have a leading zero. If you wish to change your number selection, scan Cancel on the “Imager Keypad Number Symbols” page. E-SW-BLUESCANPG-A 0.6 Seconds Bluetooth Ring Scanner Guide...

  • Page 196: Trigger Modes

    Trigger Modes Note: LXE mobile devices with ring decoders are designed to be operated in Level Trigger Mode. LXE recommends leaving the Trigger Mode default value unchanged. Parameter Default Value: Use this parameter to determine when the laser is activated and decoding begins, how long the laser remains on and what determines the cessation of the laser scan and decode process.

  • Page 197: Report Version

    SE4400 Imager Barcodes Cancel See also Presentation Mode Session Timeout. Report Version Scan the following barcode to view the version of software currently installed in the ring decoder. E-SW-BLUESCANPG-A Bluetooth Ring Scanner Guide...

  • Page 198: Transmit No Code Id Character

    Scan one of the following barcodes to select either no code ID character, a Symbol Code ID character or an AIM Code ID character. Transmit No Code ID Character Transmit Symbol Code ID Character Bluetooth Ring Scanner Guide None UPC-A, UPC-E, UPC-E1, EAN-8, EAN-13 Code 39, Code 32...

  • Page 199: Transmit Aim Code Id Character

    Example: A Full ASCII barcode with check character W,A+I+MI+DW, is transmitted as ]A7AimId where 7 = (3+4). No option specified at this time. Always transmit 0. Example: A Trioptic barcode 412356 is transmitted as ]X0412356 Bluetooth Ring Scanner Guide...
  • Page 200 I 2 of 5 Codabar Code 93 MSI Plessey D 2 of 5 UPC/EAN Bookland EAN Bluetooth Ring Scanner Guide Option Value Option Standard data packet, No Function code 1 in first symbol position. Function code 1 in first symbol character position.
  • Page 201 903-907, 912, 914, 915. The barcode contains a UCC/EAN-128 symbol, and the first codeword is in the range 908-909. The barcode contains a UCC/EAN-128 symbol, and the first codeword is in the range 910-911. Bluetooth Ring Scanner Guide...
  • Page 202 ]EO (UPC chars) (terminator) ]E2 (supplemental) (terminator) Therefore, a UPC with two supplemental characters, 01234567890510, is transmitted to the host as a 21-character string, ]E00012345678905]E110. Bluetooth Ring Scanner Guide Option Value Option Example: A PDF417 barcode ABCD, with no transmission protocol enabled, is transmitted as ]L2ABCD.

  • Page 203: Prefix / Suffix Values

    Next, scan four numeric barcodes that correspond to the computer keycode using the “Imager Keypad Number Symbols” at the end of this chapter. If you wish to change your selection, scan Cancel on the “Imager Keypad Number Symbols” page. E-SW-BLUESCANPG-A Null Bluetooth Ring Scanner Guide...

  • Page 204: Suffix 2

    Next, scan four numeric barcodes that correspond to the computer keycode using the “Imager Keypad Number Symbols” at the end of this chapter. If you wish to change your numeric selection, scan Cancel on the “Imager Keypad Number Symbols” page. Bluetooth Ring Scanner Guide SE4400 Imager Barcodes E-SW-BLUESCANPG-A...

  • Page 205: Scan Data Transmission Format

    If you wish to change your selection, scan the Cancel barcode and scan again. Set the Scan Data Transmission Format parameter by scanning one of the following barcodes: Data As Is [Data] [Suffix 1] [Data] [Suffix 2] [Data] [Suffix 1] [Suffix 2] [Prefix] [Data] E-SW-BLUESCANPG-A Data As Is Bluetooth Ring Scanner Guide...
  • Page 206 [Prefix] [Data] [Suffix 1] [Prefix] [Data] [Suffix 2] [Prefix] [Data] [Suffix 1] [Suffix 2] Cancel Now you are ready to scan one of the “Prefix/Suffix Values” barcodes. Bluetooth Ring Scanner Guide SE4400 Imager Barcodes E-SW-BLUESCANPG-A...

  • Page 207: Transmit "No Read" Message

    Scan a barcode below to select whether or not to transmit a No Read message. When enabled, the characters NR are transmitted when a barcode is not decoded. When disabled, if a symbol does not decode, nothing is sent to the host. Enable No Read Disable No Read E-SW-BLUESCANPG-A Disable Bluetooth Ring Scanner Guide...

  • Page 208: Upc-A

    Select an option by scanning either of the barcodes shown below. Enable UPC-A Disable UPC-A UPC-E Parameter Default Value: Select an option by scanning either of the barcodes shown below. Enable UPC-E Disable UPC-E Bluetooth Ring Scanner Guide SE4400 Imager Barcodes Enable Enable E-SW-BLUESCANPG-A...

  • Page 209: Ean-8/Jan-8

    Enable UPC-E1 Disable UPC-E1 Note: UPC-E1 is not a UCC (Uniform Code Council) approved symbology. EAN-8/JAN-8 Parameter Default Value: Select an option by scanning either of the barcodes shown below. Enable EAN-8/JAN-8 Disable EAN-8/JAN-8 E-SW-BLUESCANPG-A Disable Enable Bluetooth Ring Scanner Guide...

  • Page 210: Ean-13/Jan-13

    EAN-13/JAN-13 Parameter Default Value: Select an option by scanning either of the barcodes shown below. Enable EAN-13/JAN-13 Disable EAN-13/JAN-13 Bluetooth Ring Scanner Guide SE4400 Imager Barcodes Enable E-SW-BLUESCANPG-A...

  • Page 211: Bookland Ean

    Disable Bookland EAN Bookland Format Parameter Default Value: This parameter is used to control the Bookland Format. Select an option by scanning either of the barcodes shown below. Bookland 10 Bookland 13 E-SW-BLUESCANPG-A Disable Bookland 10 Bluetooth Ring Scanner Guide...

  • Page 212: Decode Upc/Ean/Jan Supplementals (2 And 5 Digits)

    When this option is selected you must assign a value to the “Decode UPC/EAN Supplemental Redundancy” parameter. of 5 or more is recommended. The scanner will identify supplementals for EAN-13/JAN-13 barcodes that start with a 378 or 379 prefix only. All other UPC/EAN/JAN codes are decoded immediately and the supplemental characters ignored.
  • Page 213 SE4400 Imager Barcodes Autodiscriminate UPC/EAN/JAN Supplementals Enable 378/379 Supplemental Mode Enable 978 Supplemental Mode Enable Smart Supplemental Mode Cancel E-SW-BLUESCANPG-A Bluetooth Ring Scanner Guide...

  • Page 214: Upc/Ean/Jan Supplemental Redundancy

    This parameter determines whether the symbol will be transmitted with or without the UPC-A check digit. Select an option by scanning either of the barcodes shown below. Enable Transmit UPC-A Check Digit Disable Transmit UPC-A Check Digit Bluetooth Ring Scanner Guide SE4400 Imager Barcodes 10 Times Enable E-SW-BLUESCANPG-A...

  • Page 215: Transmit Upc-E Check Digit

    This parameter determines whether the symbol will be transmitted with or without the UPC-E1 check digit. Select an option by scanning either of the barcodes shown below. Enable Transmit UPC-E1 Check Digit Disable Transmit UPC-E1 Check Digit E-SW-BLUESCANPG-A Enable Enable Bluetooth Ring Scanner Guide...

  • Page 216: Upc-A Preamble

    Select an option by scanning one of the barcodes shown below. No Preamble System Character System Character and Country Code (“0” for USA) Bluetooth Ring Scanner Guide SE4400 Imager Barcodes System Character [data] [schar] [data] [country code] [schar] [data] E-SW-BLUESCANPG-A...

  • Page 217: Upc-E Preamble

    System Character and Country Code Select an option by scanning one of the barcodes shown below. No Preamble System Character System Character and Country Code (“0” for USA) E-SW-BLUESCANPG-A System Character [data] [schar] [data] [country code] [schar] [data] Bluetooth Ring Scanner Guide...

  • Page 218: Upc-E1 Preamble

    Select an option by scanning one of the barcodes shown below. No Preamble System Character System Character and Country Code (“0” for USA) Bluetooth Ring Scanner Guide SE4400 Imager Barcodes System Character [data] [schar] [data] [country code] [schar] [data] E-SW-BLUESCANPG-A...

  • Page 219: Convert Upc-E To Upc-A

    A programming selections (e.g. Preamble, Check Digit, etc.). When disabled, UPC-E (zero suppressed) decoded data is transmitted without conversion. Select an option by scanning either of the barcodes shown below. Enable UPC-E to UPC-A Disable UPC-E to UPC-A E-SW-BLUESCANPG-A Disable Bluetooth Ring Scanner Guide...

  • Page 220: Convert Upc-E1 To Upc-A

    A programming selections (e.g. Preamble, Check Digit, etc.). When disabled, UPC-E1 (zero suppressed) decoded data is transmitted without conversion. Select an option by scanning either of the barcodes shown below. Enable UPC-E1 to UPC-A Disable UPC-E1 to UPC-A Bluetooth Ring Scanner Guide SE4400 Imager Barcodes Disable E-SW-BLUESCANPG-A...

  • Page 221: Ean-8/Jan-8 Extend

    When disabled, EAN-8 symbols are transmitted as is and parameter “Convert EAN-8 to EAN-13 Type” setting is ignored. Select an option by scanning either of the barcodes shown below. Enable EAN-8/JAN-8 Zero Extend Disable EAN-8/JAN-8 Zero Extend E-SW-BLUESCANPG-A Disable Bluetooth Ring Scanner Guide...

  • Page 222: Ucc Coupon Extended Code

    UPCA, EAN-13 and EAN-128 must be enabled to scan all types of Coupon Codes. Enable UCC Coupon Extended Code Disable UCC Coupon Extended Code Note: Use the Decode UPC/EAN Supplemental Redundancy parameter to control autodiscrimination of the EAN128 (right half) of a coupon code. Bluetooth Ring Scanner Guide SE4400 Imager Barcodes Disable E-SW-BLUESCANPG-A...

  • Page 223: Code 128

    Set this parameter by scanning either of the barcodes shown below. Enable Code 128 Disable Code 128 UCC/EAN-128 Parameter Default Value: Set this parameter by scanning either of the barcodes shown below. Enable UCC/EAN-128 Disable UCC/EAN-128 E-SW-BLUESCANPG-A Enable Enable Bluetooth Ring Scanner Guide...

  • Page 224: Isbt-128

    ISBT-128 is a variant of Code 128 used in the blood bank industry. If necessary, the host must perform concatenation of the ISBT data. Set this parameter by scanning either of the barcodes shown below. Enable ISBT-128 Disable ISBT-128 Bluetooth Ring Scanner Guide SE4400 Imager Barcodes Enable E-SW-BLUESCANPG-A...

  • Page 225: Trioptic Code 39

    When Trioptic Code 39 is enabled, set the “Code 39 Full ASCII” parameter to disabled. Both parameters should not be enabled simultaneously. Set this parameter by scanning either of the barcodes shown below. Enable Trioptic Code 39 Disable Trioptic Code 39 E-SW-BLUESCANPG-A Enable Disable Bluetooth Ring Scanner Guide...

  • Page 226: Convert Code 39 To Code 32

    When enabled, “Convert Code 39 to Code 32” parameter must also be enabled. Set this parameter by scanning either of the barcodes shown below. Enable Code 32 Prefix Disable Code 32 Prefix Bluetooth Ring Scanner Guide SE4400 Imager Barcodes Disable Disable...

  • Page 227: Set Length(S) For Code 39

    Next, scan four numeric barcodes that correspond to the desired value. Single digit numbers must have a leading zero. To correct an error or to change a selection, scan Cancel on the “Imager Keypad Number Symbols” page. E-SW-BLUESCANPG-A Bluetooth Ring Scanner Guide...

  • Page 228: Length Within Range

    To correct an error or to change a selection, scan Cancel on the “Imager Keypad Number Symbols” page. Any Length This option decodes Code 39 barcodes containing any number of characters. To set any length, scan this Any Length barcode: Bluetooth Ring Scanner Guide SE4400 Imager Barcodes E-SW-BLUESCANPG-A...

  • Page 229: Code 39 Check Digit Verification

    Enable this feature if the code 39 barcodes contain a Modulo 43 check digit. Set this parameter by scanning either of the barcodes shown below. Enable Code 39 Check Digit Verification Disable Code 39 Check Digit Verification E-SW-BLUESCANPG-A Disable Bluetooth Ring Scanner Guide...

  • Page 230: Transmit Code 39 Check Digit

    Parameter setting for “Code 39 Check Digit Verification” has no effect on this parameter value. Set this parameter by scanning either of the barcodes shown below. Enable Transmit Code 39 Check Digit Disable Transmit Code 39 Check Digit Bluetooth Ring Scanner Guide SE4400 Imager Barcodes Disable E-SW-BLUESCANPG-A...

  • Page 231: Code 39 Full Ascii Conversion

    Code 39 Full ASCII interprets the barcode special character ($ + % /) preceding a Code 39 character and assigns an ASCII character value to the pair. See the table titled “ASCII Character Equivalents” at the end of the “Appendix”. E-SW-BLUESCANPG-A Disable Bluetooth Ring Scanner Guide...

  • Page 232: Set Lengths For Code 93

    The length of a code refers to the number of characters, including check digits, the code contains. See the table titled “ASCII Character Equivalents” at the end of the “Appendix”. Bluetooth Ring Scanner Guide SE4400 Imager Barcodes Disable Code 93...

  • Page 233: One Discrete Length (Parameter L1)

    Next, scan four numeric barcodes that correspond to the desired value. Single digit numbers must have a leading zero. To correct an error or to change a selection, scan Cancel on the “Imager Keypad Number Symbols” page. E-SW-BLUESCANPG-A Bluetooth Ring Scanner Guide...

  • Page 234: Length Within Range

    To correct an error or to change a selection, scan Cancel on the “Imager Keypad Number Symbols” page. Any Length This option decodes Code 93 barcodes containing any number of characters. To set any length, scan this Code 93 Any Length barcode: Bluetooth Ring Scanner Guide SE4400 Imager Barcodes E-SW-BLUESCANPG-A...

  • Page 235: Set Lengths For Code 11

    The length of a code refers to the number of characters, including check digits, the code contains. It also includes any start or stop characters. See the table titled “ASCII Character Equivalents” at the end of the “Appendix”. E-SW-BLUESCANPG-A Disable Bluetooth Ring Scanner Guide...

  • Page 236: One Discrete Length (Parameter L1)

    Next, scan four numeric barcodes that correspond to the desired value. Single digit numbers must have a leading zero. To correct an error or to change a selection, scan Cancel on the “Imager Keypad Number Symbols” page. Bluetooth Ring Scanner Guide SE4400 Imager Barcodes E-SW-BLUESCANPG-A...

  • Page 237: Length Within Range

    Cancel on the “Imager Keypad Number Symbols” page. Any Length This option decodes Code 11 barcodes containing any number of characters. To set any length, scan this Code 11 Any Length barcode: E-SW-BLUESCANPG-A Bluetooth Ring Scanner Guide...

  • Page 238: Code 11 Check Digit Verification

    Enable Code 11 Check Digit Verification when Transmit Code 11 Check Digits is enabled. Set this parameter by scanning one of the barcodes shown below. Disable Code 11 Check Digit Verification One Check Digit Two Check Digits Bluetooth Ring Scanner Guide SE4400 Imager Barcodes Disable E-SW-BLUESCANPG-A...

  • Page 239: Transmit Code 11 Check Digits

    Transmit Code 11 Check Digits Parameter Default Value: Code 11 Check Digit Verification must be enabled for this parameter to function. Transmit (Enable) Code 11 Check Digits Do Not Transmit (Disable) Code 11 Check Digits E-SW-BLUESCANPG-A Do Not Transmit (Disable) Bluetooth Ring Scanner Guide...

  • Page 240: Interleaved 2 Of 5 (Itf)

    • or lengths within a specific range. The length of a code refers to the number of characters, including check digits, the code contains. See the table titled “ASCII Character Equivalents” at the end of the “Appendix”. Bluetooth Ring Scanner Guide SE4400 Imager Barcodes Enable...

  • Page 241: One Discrete Length (Parameter L1)

    Next, scan four numeric barcodes that correspond to the desired value. Single digit numbers must have a leading zero. To correct an error or to change a selection, scan Cancel on the “Imager Keypad Number Symbols” page. E-SW-BLUESCANPG-A Bluetooth Ring Scanner Guide...

  • Page 242: Length Within Range

    This option decodes I 2 of 5 barcodes containing any number of characters. Note: Selecting this option may lead to misdecodes for I 2 of 5 codes. To set any length, scan this I 2 of 5 Any Length barcode: Bluetooth Ring Scanner Guide SE4400 Imager Barcodes E-SW-BLUESCANPG-A...

  • Page 243: I 2 Of 5 Check Digit Verification

    USS (Uniform Symbology Specification) or OPCC (Optical Product Code Council). Set this parameter by scanning one of the barcodes shown below. Disable I 2 of 5 Check Digit Verification USS (Uniform Symbology Specification) OPCC (Optical Product Code Council) E-SW-BLUESCANPG-A Disable Bluetooth Ring Scanner Guide...

  • Page 244: Transmit I 2 Of 5 Check Digit

    Parameter setting for “I 2 of 5 Check Digit Verification” has no effect on this parameter value. Set this parameter by scanning either of the barcodes shown below. Enable Transmit I 2 of 5 Check Digit Disable Transmit I 2 of 5 Check Digit Bluetooth Ring Scanner Guide SE4400 Imager Barcodes Disable E-SW-BLUESCANPG-A...

  • Page 245: Convert I 2 Of 5 To Ean

    When enabled, the parameter converts a 14 character I 2 of 5 barcode into EAN-13 and transmits it to the host as EAN-13. Set this parameter by scanning either of the barcodes shown below. Enable Convert I 2 of 5 to EAN-13 Disable Convert I 2 of 5 to EAN-13 E-SW-BLUESCANPG-A Disable Bluetooth Ring Scanner Guide...

  • Page 246: Set Lengths For Discrete 2 Of 5

    To prevent this, select specific lengths (using D2 of 5 – One Discrete Length and D 2 of 5 Two Discrete Lengths) for D 2 of 5 applications. See the table titled “ASCII Character Equivalents” at the end of the “Appendix”. Bluetooth Ring Scanner Guide SE4400 Imager Barcodes Disable...

  • Page 247: One Discrete Length (Parameter L1)

    Next, scan four numeric barcodes that correspond to the desired value. Single digit numbers must have a leading zero. To correct an error or to change a selection, scan Cancel on the “Imager Keypad Number Symbols” page. E-SW-BLUESCANPG-A Bluetooth Ring Scanner Guide...

  • Page 248: Length Within Range

    Selecting this option may lead to misdecodes for D 2 of 5 codes. See note in Set Lengths for Discrete 2 of 5. To set any length, scan this D 2 of 5 Any Length barcode: Bluetooth Ring Scanner Guide SE4400 Imager Barcodes E-SW-BLUESCANPG-A...

  • Page 249: Codabar

    Set this parameter by scanning either of the barcodes shown below. Note: Symbol length does not include start and stop characters. Enable CLSI Editing Disable CLSI Editing E-SW-BLUESCANPG-A Disable Disable characters of a 14 character Codabar symbol. Bluetooth Ring Scanner Guide...

  • Page 250: Notis Editing

    The length of a code refers to the number of characters, including check digits, the code contains. It also includes any start or stop characters. See the table titled “ASCII Character Equivalents” at the end of the “Appendix”. Bluetooth Ring Scanner Guide SE4400 Imager Barcodes Disable...

  • Page 251: One Discrete Length (Parameter L1)

    Next, scan four numeric barcodes that correspond to the desired value. Single digit numbers must have a leading zero. To correct an error or to change a selection, scan Cancel on the “Imager Keypad Number Symbols” page. E-SW-BLUESCANPG-A Bluetooth Ring Scanner Guide...

  • Page 252: Length Within Range

    Cancel on the “Imager Keypad Number Symbols” page. Any Length This option decodes Codabar barcodes containing any number of characters. To set any length, scan this Codabar Any Length barcode: Bluetooth Ring Scanner Guide SE4400 Imager Barcodes E-SW-BLUESCANPG-A...

  • Page 253: Set Length(S) For Msi

    To prevent this, select specific lengths (using MSI One Discrete Length and MSI Two Discrete Lengths) for MSI applications. See the table titled “ASCII Character Equivalents” at the end of the “Appendix”. E-SW-BLUESCANPG-A Disable Bluetooth Ring Scanner Guide...

  • Page 254: One Discrete Length (Parameter L1)

    Next, scan four numeric barcodes that correspond to the desired value. Single digit numbers must have a leading zero. To correct an error or to change a selection, scan Cancel on the “Imager Keypad Number Symbols” page. Bluetooth Ring Scanner Guide SE4400 Imager Barcodes E-SW-BLUESCANPG-A...

  • Page 255: Length Within Range

    This option decodes MSI barcodes containing any number of characters. Note: Selecting this option may lead to misdecodes for MSI codes. See note in section titled Set Lengths for MSI. To set any length, scan this MSI Any Length barcode: E-SW-BLUESCANPG-A Bluetooth Ring Scanner Guide...

  • Page 256: Msi Check Digits

    When Two MSI Check Digits is selected, an MSI Check Digit Algorithm must also be selected. Set the number of check digits to be included with the barcode by scanning either of the barcodes shown below. One MSI check digit Two MSI check digits Bluetooth Ring Scanner Guide SE4400 Imager Barcodes E-SW-BLUESCANPG-A...

  • Page 257: Transmit Msi Check Digit

    Parameter Default Value: When enabled, the check digit is transmitted with the data. Set this parameter by scanning either of the barcodes shown below. Enable Transmit MSI Check Digit Disable Transmit MSI Check Digit E-SW-BLUESCANPG-A Disable Bluetooth Ring Scanner Guide...

  • Page 258: Msi Check Digit Algorithm

    Either of the two following algorithms may be selected. Set this parameter by scanning either of the barcodes shown below. Mod 10/Mod 11 MSI Check Digit Algorithm Mod 10/Mod 10 MSI Check Digit Algorithm Bluetooth Ring Scanner Guide SE4400 Imager Barcodes Mod10/Mod10 E-SW-BLUESCANPG-A...

  • Page 259: Postal Codes

    To enable or disable US Postnet, scan the appropriate barcode: Enable US Postnet Disable US Postnet US Planet Parameter Default Value: To enable or disable US Planet, scan the appropriate barcode: Enable US Planet Disable US Planet E-SW-BLUESCANPG-A Enable Enable Bluetooth Ring Scanner Guide...

  • Page 260: Uk Postal

    Transmit UK Postal Check Digit Parameter Default Value: Select whether to transmit UK Postal data with or without the check digit: Transmit UK Postal Check Digit Do Not Transmit UK Postal Check Digit Bluetooth Ring Scanner Guide SE4400 Imager Barcodes Enable Transmit E-SW-BLUESCANPG-A...

  • Page 261: Japan Postal

    To enable or disable Japan Postal, scan the appropriate barcode: Enable Japan Postal Disable Japan Postal Australian Postal Parameter Default Value: To enable or disable Australian Postal, scan the appropriate barcode: Enable Australian Postal Disable Australian Postal E-SW-BLUESCANPG-A Enable Enable Bluetooth Ring Scanner Guide...

  • Page 262: Dutch Postal

    Dutch Postal Parameter Default Value: To enable or disable Dutch Postal, scan the appropriate barcode: Enable Dutch Postal Disable Dutch Postal Bluetooth Ring Scanner Guide SE4400 Imager Barcodes Enable E-SW-BLUESCANPG-A...

  • Page 263: Transmit Us Postal Check Digit

    Transmit US Postal Check Digit Do Not Transmit US Postal Check Digit 4State Postal Parameter Default Value: To enable or disable 4State Postal, scan the appropriate barcode: Enable 4State Postal Disable 4State Postal E-SW-BLUESCANPG-A Transmit Disable Bluetooth Ring Scanner Guide...

  • Page 264: Gs1 Databar Omnidirectional (Rss-14)

    To enable or disable RSS Limited, scan the appropriate barcode: Enable GS1 DataBar Limited (RSS Limited) Disable GS1 DataBar Limited (RSS Limited) See Also: Convert GS1 DataBar (RSS) to UPC/EAN Bluetooth Ring Scanner Guide SE4400 Imager Barcodes Enable Enable E-SW-BLUESCANPG-A...

  • Page 265: Gs1 Databar Expanded (Rss Expanded)

    Note that neither the system character nor the check digit can be stripped. Enable Convert GS1 DataBar (RSS) to UPC/EAN Disable Convert GS1 DataBar (RSS) to UPC/EAN E-SW-BLUESCANPG-A Enable Enable Bluetooth Ring Scanner Guide...

  • Page 266: Composite Cc-C

    Enable Composite CC-C Disable Composite CC-C Composite CC-A/B Parameter Default Value: Scan one of the following barcodes to enable or disable Composite barcodes of type CC-A/B. Enable Composite CC-A/B Disable Composite CC-A/B Bluetooth Ring Scanner Guide SE4400 Imager Barcodes Disable Disable E-SW-BLUESCANPG-A...

  • Page 267: Composite Tlc-39

    SE4400 Imager Barcodes Composite TLC-39 Parameter Default Value: Scan one of the following barcodes to enable or disable Composite barcodes of type TLC-39. Enable Composite TLC-39 Disable Composite TLC-39 E-SW-BLUESCANPG-A Disable Bluetooth Ring Scanner Guide...

  • Page 268: Upc Composite Mode

    UPC Composites UPC Never Linked UPC Always Linked Autodiscriminate UPC Composites Bluetooth Ring Scanner Guide UPC Always Linked Transmit UPC barcodes regardless of whether a 2D symbol is detected. Transmit UPC barcodes and the 2D portion. If 2D is not present, the UPC barcode does not transmit.

  • Page 269: Ucc/Ean Code 128 Emulation Mode

    Select whether to enable or disable UCC/EAN Code 128 Emulation Mode for UCC/EAN Composite Codes. Parameter Default Value: Enable UCC/EAN Code 128 Emulation Mode for UCC/EAN Composite Codes Disable UCC/EAN Code 128 Emulation Mode for UCC/EAN Composite Codes E-SW-BLUESCANPG-A Disable Bluetooth Ring Scanner Guide...

  • Page 270: D Symbologies

    To enable or disable PDF417, scan the appropriate barcode below. Enable PDF417 Disable PDF417 MicroPDF417 Parameter Default Value: To enable or disable MicroPDF417, scan the appropriate barcode below. Enable MicroPDF417 Disable MicroPDF417 Bluetooth Ring Scanner Guide SE4400 Imager Barcodes Enable Disable E-SW-BLUESCANPG-A...

  • Page 271: Code 128 Emulation

    Enable Code 128 Emulation Disable Code 128 Emulation When this parameter is enabled, the scanner transmits data from certain MicroPDF417 symbols as if it was encoded in Code 128 symbols. Transmit AIM Symbology Identifiers must be enabled for this parameter to work.

  • Page 272: Data Matrix

    Disable Data Matrix Data Matrix Inverse Parameter Default Value: This parameter controls the setting of the DataMatrix inverse decoder. Scan the appropriate barcode below. Regular Only Inverse Only Inverse Auto Detect Bluetooth Ring Scanner Guide SE4400 Imager Barcodes Enable Regular Only E-SW-BLUESCANPG-A...

  • Page 273: Maxicode

    To enable or disable Maxicode scan the appropriate barcode below. Enable Maxicode Disable Maxicode QR Code Parameter Default Value: To enable or disable QR Code scan the appropriate barcode below. Enable QR Code Disable QR Code E-SW-BLUESCANPG-A Enable Enable Bluetooth Ring Scanner Guide...

  • Page 274: Microqr

    Disable MicroQR QR Inverse Parameter Default Value: This parameter controls the setting of the QR Inverse decoder. Scan the appropriate barcode below. Regular Only Inverse Only Inverse Auto Detect Bluetooth Ring Scanner Guide SE4400 Imager Barcodes Enable Regular Only E-SW-BLUESCANPG-A...

  • Page 275: Aztec

    To enable or disable Aztec scan the appropriate barcode below. Enable Aztec Disable Aztec Aztec Inverse Parameter Default Value: This parameter controls the setting of the Aztec Inverse decoder. Scan the appropriate barcode below. Regular Only Inverse Only Inverse Auto Detect E-SW-BLUESCANPG-A Enable Regular Only Bluetooth Ring Scanner Guide...

  • Page 276: Redundancy Level

    I 2 of 5 Codabar Redundancy Level 4 The following code types must be successfully read three times before being decoded: Code Type Bluetooth Ring Scanner Guide Redundancy Level 1 Code Length 8 characters or less 4 characters or less...
  • Page 277 SE4400 Imager Barcodes Redundancy Level 1 Redundancy Level 2 Redundancy Level 3 Redundancy Level 4 Cancel E-SW-BLUESCANPG-A Bluetooth Ring Scanner Guide...

  • Page 278: Security Level

    Level barcode on this page and the following page. Security Level 0 Security Level 1 Security Level 2 Bluetooth Ring Scanner Guide Security Level 1 This setting allows the decoder to operate in its most aggressive state, while providing sufficient security in decoding most “in-spec” barcodes.
  • Page 279 SE4400 Imager Barcodes Security Level 3 Cancel E-SW-BLUESCANPG-A Bluetooth Ring Scanner Guide...

  • Page 280: Intercharacter Gap Size

    Due to various barcode-printing technologies, this gap can grow larger than the maximum size allowed, preventing the decoder from decoding the symbol. If this problem occurs, scan the Large Intercharacter Gaps parameter to tolerate these out-of- specification barcodes. Normal Intercharacter Gaps Large Intercharacter Gaps Bluetooth Ring Scanner Guide SE4400 Imager Barcodes Normal E-SW-BLUESCANPG-A...

  • Page 281: Imager Keypad Number Symbols

    Use these numeric value symbols to enter numeric input in the course of performing an imager engine system configuration. To correct an error or change a selection, scan Cancel then scan a desired barcode. E-SW-BLUESCANPG-A Bluetooth Ring Scanner Guide...
  • Page 282 Cancel Bluetooth Ring Scanner Guide SE4400 Imager Barcodes E-SW-BLUESCANPG-A...

  • Page 283: Scanner Identification Label

    Chapter 5 Scan Engine Technical Specifications Scanner Identification Label The label specifying which laser engine is installed in the LXE mobile device is usually on the back of the mobile device, next to the laser warning label. Decode Zones The scan ranges listed in the following tables are based on the following factors: •...

  • Page 284: Se955-I000Wr Standard Range Laser Scanner

    40 mil 55 mil * Near ranges are largely dependent upon the width of the barcode and the scan angle. Figure 5-1 Decode Zones – SE955-I000WR Standard Range Laser Ring Scanner Bluetooth Ring Scanner Guide Scan Engine Technical Specifications Guaranteed Working Ranges Near 5.50 in / 13.97 cm...

  • Page 285: Se4400 Laser Imager

    9.5 in / 24.1 cm 5.0 in / 12.7 cm 5.0 in / 12.7 cm 5.5 in / 13.9 cm 5.5 in / 13.9 cm 6.0 in / 15.2 cm 6.0 in / 15.2 cm 8.0 in / 20.3 cm Bluetooth Ring Scanner Guide...

  • Page 286: Far Focus Decode Distances Stopped Here

    2. Working range specifications at temperature = 23°C, pitch=15°, roll=0°, skew=0°, photographic quality, ambient light ~30 ft-c, humidity 45-70% RH. Figure 5-3 Imager Far Focus Decode Distances Bluetooth Ring Scanner Guide Typical Working Range 7.5 in / 19.1 cm 10.0 in / 25.4 cm 5.5 in / 14.0 cm...

  • Page 287: Pl4407

    17.0 in / 43.2 cm 5.0 in / 12.7 cm 5.0 in / 12.7 cm 7.0 in / 17.8 cm 8.0 in / 20.3 cm 11.5 in / 29.2 cm 11.0 in / 27.9 cm 15.5 in / 39.4 cm Bluetooth Ring Scanner Guide...

  • Page 288: Pl4407

    2. Working range specifications at temperature = 23°C, pitch=15°, roll=0°, skew=0°, photographic quality, humidity 45-70%RH. 3. Range measurements are when VCC_ILLUM is powered off of 3.0 V. Powering VCC_ILLUM off of 3.3 V yields slightly improved working ranges in darkness. Bluetooth Ring Scanner Guide Typical Working Ranges Focus Position Near Near 3.5 in / 8.9 cm...

  • Page 289: A Ppendix

    A desktop/laptop Win XP or Win 2000 PC with an available USB port. A Bluetooth module and a fully charged battery. Bluetooth Module Firmware update cable (8650A051CBLBTUPDATE). Firmware update file (contact your LXE representative to obtain the latest Bluetooth Module firmware update file). Note: A Bluetooth module is required when performing the initial install of the BlueCore Device Firmware Update program on the PC.
  • Page 290 Next. 11. Click Continue Anyway when the dialog box appears stating “the driver has not passed Windows logo testing to verify compatibility”. 12. Select Finish on the next dialog box. Bluetooth Ring Scanner Guide Appendix E-SW-BLUESCANPG-A...
  • Page 291 14. Click the plus sign next to Universal Serial Bus controllers. Verify the BTRS Ringscanner in DFU mode is present. Close all open windows and return to the PC desktop. 15. You are ready to update the Bluetooth Ring Scanner module firmware. E-SW-BLUESCANPG-A...

  • Page 292: Update The Module Firmware

    6. The upgrade process proceeds and ends with a Successful Upgrade message (see step 7). The Bluetooth module may emit a series of beeps or the blue LED may stop flashing and remain illuminated until the upgrade is finished. Bluetooth Ring Scanner Guide Appendix E-SW-BLUESCANPG-A...
  • Page 293 Appendix 7. Click Finish. E-SW-BLUESCANPG-A Bluetooth Ring Scanner Guide...

  • Page 294: Ascii Character Equivalents

    1021 1022 1023 1024 1025 1026 1027 1028 1029 1030 Bluetooth Ring Scanner Guide ASCII Character Equivalents Hex Value Full ASCII Code 39 Encode Char. Appendix Therefore, they are not included in Keystroke CTRL 2 CTRL A CTRL B CTRL C...
  • Page 295 1051 1052 1053 1054 1055 1056 1057 1058 1059 1060 1061 1062 1063 1064 1065 1066 1067 E-SW-BLUESCANPG-A Hex Value Full ASCII Code 39 Encode Char. Space Keystroke CTRL - Space ‘ & ’ < > Bluetooth Ring Scanner Guide...
  • Page 296 1081 1082 1083 1084 1085 1086 1087 1088 1089 1090 1091 1092 1093 1094 1095 1096 1097 1098 1099 1100 1101 1102 1103 1104 Bluetooth Ring Scanner Guide Hex Value Full ASCII Code 39 Encode Char. Appendix Keystroke ‘ E-SW-BLUESCANPG-A...
  • Page 297 1119 1120 1121 1122 1123 1124 1125 1126 1127 Beep Related Programming Barcodes for the ring scanner / ring imager are not supported by LXE E-SW-BLUESCANPG-A Hex Value Full ASCII Code 39 Encode Char. Keystroke Undefined Bluetooth Ring Scanner Guide...
  • Page 298 Appendix Bluetooth Ring Scanner Guide E-SW-BLUESCANPG-A...

  • Page 299: Index

    SE4400 ... 244 MSI Plessey SE955 ... 132 ASCII 29 GS control character SE955 ... 107 ASCII Character Equivalents ... 284 Assemble Battery and Ring Scanner ... 9 Module... 9 Assemble components... 9 Australian Postal SE4400... 250 Autodiscriminate UPC Composites SE4400... 258 Autodiscriminate UPC/EAN Supplementals SE4400...
  • Page 300 Suspend timeout ...32 Timeout reconnect...37 reconnect interval...35 Suspend...32 Uppercase letters a-z ...53 Volume ...41 Bluetooth module LXE barcodes...30 Bluetooth ring scanner and ring imager, described ...5 Bluetooth ring scanner assembled...11 Bookland EAN AIM Code SE4400...188 SE955...81 SE4400 ...200 SE955 ...136 Bookland Format SE4400 ...200...
  • Page 301 Composite TLC-39 SE4400 ...167, 257 Configuring the Bluetooth module ...30 Connect scanner cable ...9 Connecting the Ring Device Cable...9 E-SW-BLUESCANPG-A Contacting LXE ... 27 Convert Code 39 to Code 32 SE955 ...111 EAN-8 to EAN-13 SE955 ... 140 I 2 of 5 to EAN-13 SE4400 ...
  • Page 302 SE955...140 Zero Extend SE4400...210 SE955...140, 146 Encode Char ...284 Equivalents, ASCII ...284 Event Reporting ...22 Bluetooth Ring Scanner Guide Finger strap assembly, disassembly... 17 Firmware update... 18 Focus Mode, SE4400 ... 177 Format, Bookland SE4400... 200 Function Code 1 (FNC1) SE955 ...
  • Page 303 ... 35 Suspend ... 32 Uppercase letters a-z... 53 User Name ... 43 LXE Programming Barcodes Focus Mode, Imager ... 42 LXE Tethered Scanners and Bluetooth... 2 Manuals on the WWW ... 27 Maxicode SE4400... 263 MicroPDF417 SE4400... 260 MicroQR SE4400...
  • Page 304 SE4400 ...245 MSI Plessey AIM Code SE4400...188 SE955...81 Any Length SE955...132 Check Digit Algorithm Bluetooth Ring Scanner Guide SE955 ... 129 Check Digits SE955 ... 130 Length Within Range SE955 ... 132 One Discrete Length SE955 ... 131 SE4400... 242 SE955 ...
  • Page 305 Scan Data Transmission Format SE4400 ...194 SE955 ...77 E-SW-BLUESCANPG-A Scan Range... 273 Scan Value... 284 Scanner Performance LXE Support... 23 Scanner Power Mode SE955 ... 86 SE4400 Barcode Types ... 162 SE4400 Defaults Codabar Lengths SE4400 ... 239 Code 11 Lengths SE4400 ...
  • Page 306 SE955 ... 112, 116 Bluetooth Ring Scanner Guide Troubleshooting Aiming Dot ... 60 Aiming Modes ... 60 Ambient lighting and scanner problems... 23 Barcode quality ... 23 Barcode scanning performance ... 23 Barcode symbology, problems ... 23 Battery ... 10 module firmware update ...
  • Page 307 Warnings and Labels Ring Scanner... 3 Write Custom Defaults SE955 ... 65, 88 Zero Extend SE4400... 210 SE955 ... 146 Zero Suppressed UPC-E to UPC-A... 139, 208 UPC-E1 to UPC-A SE4400 ... 209 SE955 ... 139 Bluetooth Ring Scanner Guide...
  • Page 308 Index Bluetooth Ring Scanner Guide E-SW-BLUESCANPG-A...

Table of Contents