Related Manuals for Zenitel ELSII-10HM
Summary of Contents for Zenitel ELSII-10HM
- Page 1 Network Speakers ELSII-10HM ELSII-10LHM ELSII-10PM ELSII-10WM ELSIR-10CM Mounting & Installation Manual A100K12150...
- Page 2 About Contents This document serves as a basic mounting and installation guide for Zenitels Safety Information range/line of Network Speakers. Featured products: ELSII-10HM/ ELSII-10LHM Item Number Item Name Description ELSII-10PM 1023301311 ELSII-10HM Network Horn Speaker, 10W, Ethernet, Microphone ELSII-10WM 1023301321...
- Page 3 These products must be installed where its weight can be fully supported. • If using anchors, plugs or screws other than those specified by Zenitel, they Mounting & Installation of ELSII-10HM / ELSII-10LHM may not be able to hold the weight of the product, and this may cause a safety hazard.
- Page 4 Due to the bracket material, use as low a tightening torque as Unscrew the ELSII-10HM/ELSII-10LHM from the mounting bracket, and possible when mounting the unit to the surface (1.5 Nm max.) place the bracket on the specified location. The speakers can be mounted both horizontally and vertically.
- Page 5 Fasten the speaker to the mounting bracket. Then remove the back plate Verify that microphone and speaker wires are correctly connected. on the speaker. Speaker Microphone Yellow Gland Microphone Wires Microphone White Black Speaker Wires Run an Ethernet cable through the cable gland on the back plate, and Reattach the back plate.
- Page 6 Cable Gland (Ø) 1xM20 (20 mm) The speaker can operate in three different modes, depending on what Value ELSII-10HM kind of server it should register to. Scan the QR-codes below according to what mode you need to configure. Weight 1.65 kg...
- Page 7 3 ELSII-10PM The speaker can be mounted both horizontally, vertically or in the ceiling. In this example the speaker is installed horisontally. ELSII-10PM 152 mm Mounting & Installation of ELSII-10PM The speakers microphone is located on the junction box. The junction box must therefore be mounted at a hight of 1,5-3m with the microphone turning down for optimal placement.
- Page 8 When the speaker is mounted, open the Junction Box. Remove lid and When mounting the unit to the surface, do not use more than 2,5 Nm remove the TKIS Kit inside. torque when fastening the speaker. Wall - recommended screws: Pan Head DIN7981 for plug (Dry wall/ Concrete) or wooden wall, etc.
- Page 9 Attach and fasten the lid. Reattach the TKIS Kit in the junction box, and verify that microphone and speaker wires are correctly connected. Make sure to tighten the cable gland sufficiently to attain IP-66 rating for watertightness, but be aware of plastic material limitations. Speaker •...
- Page 10 Connect the speaker to the network. Technical specifications Value Weight 2.35 kg Dimensions (HxWxD) 176 x 201 x160 mm IP Rating IP 66 Relative humidity < 95% not condensing Operating temperature range -40° to 70° C / -40° to 158 ° F Encapsulation material Aluminium IEEE 802.3af standard, Class 0 (0.44W...
- Page 11 4 ELSII-10WM Unscrew the ELSII-10WM from the mounting bracket, and place the bracket on the specified location. The speakers can be mounted both horizontally and ELSII-10WM vertically. In this example the speaker is mounted vertically. Mounting & Installation of ELSII-10WM Mount the speaker at a height between 1,5-3 m for optimal placement of the speaker microphones’...
- Page 12 Fasten the speaker to the mounting bracket. Then remove the back plate When mounting the unit to the surface, do not use more than 2,5 Nm on the speaker. torque when fastening the bracket. Wall - recommended screws: Pan Head DIN7981 for plug (Dry wall/ Concrete) or wooden wall, etc. Head diameter: 12,5 M6.3x 38 or 45 mm 2x Nylon plugs 2x M6 Screws...
- Page 13 Verify that microphone and speaker wires are correctly connected. Connect the speaker to the network. Speaker Speaker Wire Yellow Microphone Microphone White Wire Black Reattach the back plate To maintain the IP-66 rating on the speaker, use a tightening The speaker can operate in three different modes, depending on what torque of 0,8 Nm.
- Page 14 5 ELSIR-10CM Technical specifications Value ELSIR-10CM Weight 2. 1 kg Dimensions (HxWxD) 245 x 160 x187 mm IP Rating IP 66 + 67 Encapsulation material Aluminium Mounting Aluminium, U Shaped Bracket, Cable Gland (Ø) 1x M20 (20 mm) Mounting & Installation of ELSIR-10CM Mount the speaker in the ceiling at the maximum height of 3 meters.
- Page 15 Cut a hole in the ceiling where the speaker is to be mounted. Make sure Make sure an Ethernet cable is available through the ready made hole. there is at least 10mm clearing over the speaker. Run the cable through the cable gland on the firedome, and terminate 161,4 165,4 the cable to a RJ45 connector.
- Page 16 Use the included screws to secure the speaker to the ceiling. Reattach the fire dome Due to the speaker material, use as low a tightening torque as Make sure to tighten the cable gland sufficiently to attain IP-54 rating for watertightness, but be aware of plastic material limitations. possible when mounting the unit to the surface (1.5 Nm max.) Using screws on the speaker chassis will ground the unit.
- Page 17 Dimensions (diameter x depth) 199 x 146 mm IP Rating IP 54 The WEEE Directive does not legislate that Zenitel, as a ‘producer’, shall collect ‘end of life’ WEEE. Relative humidity < 95% not condensing This ‘end of life’ WEEE should be recycled appropriately by the owner who should use proper treatment and recycling measures.
- Page 18 A100K12150 Zenitel and its subsidiaries assume no responsibility for any errors that may appear in this publication, or for damages arising from the information therein. Zenitel, Vingtor-Stentofon and Phontech products are developed and marketed by Zenitel. The company’ s Quality Assurance System is certified to meet the requirements in NS-EN ISO 9001.