Quoizel PRV8408K Assembly Instruction

Please go to www.quoizel.com
Tools Required: Flathead screwdriver, Phillips screwdriver, pliers, wire cutters, wire strippers, electrical tape, safety glasses.
Light Source: (2) B10 Candelabra Base bulb 60W Maximum.
Estimated Assembly Time:
Preparation: Identify and inspect all parts before beginning installation. Check package content list and diagrams below to be sure all parts are
present. If any parts are missing or damaged, do not attempt to assemble, install, or operate the fixture. Contact customer service for replacement
parts.
Fixture can only be mounted in the direction indicated on page 2.
Warnings and Cautions
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly
recommend that a licensed, professional electrician perform the installation.
Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal. Do not subject
glass parts to any shock while in operation or shattering may result.
Package Contents
Crossbar
A Assembly
x 1
Alternate
Mounting
B
screw
x 2
-
STEP 1 Install Bulbs, Cage with Shade and Fixture Body
A. This fixture uses candelabra bulb with standard screw base.
Maximum 60 watts. Insert bulb and screw snugly into place.
B. Remove Lock Screws from top edge of Cage with Shade (D).
C. Insert sockets inside of shade diagonal (Refer
to Direction of Installing Sockets). Rotate
Fixture Body (C) and align holes on fixture
hood to mounting holes on top edge of the
cage. Secure them together with removed
Lock Screws. Tighten until snug with
screwdrivers.
D D
Socket
C
Socket
C
Direction of
Installing Sockets
Need assistance with parts or assembly? Call Quoizel customer service at 1-800-645-3184
2016 QuoizelInc.
Assembly Instruction Sheet #IS-PRV8408K
for product cleaning tips. Go to the
20-30 minutes
Fixture Body
C
x 1
Cage with Shade
D
x 1
C
Fixture Hood
Mounting
Hole
Shade
Figure 1
Thank you for purchasing a Quoizel product.
or visit us on-line at www.quoizel.com
For Style PRV8408K
Care + Maintenance selection.
STEP 2 - Install Crossbar Assembly
A. Pass the supply wires through the Crossbar Assembly (A). Attach
the Crossbar Assembly (A) to the Outlet Box with the head of the
Green Ground Screw facing you. Secure it with Outlet Box Screws
(not included). Tighten until snug
Note: Use the Alternate Shorter Mounting Screw (B) if your
installation requires a shorter mounting screw.
Outlet Box
Mounting Screw
or Alternate Short
Mounting Screw
STEP 3 - Test Fitting Backplate to Crossbar Assembly
A. Remove mounting balls from the Crossbar Assembly (A). Fit the
backplate on Fixture Body (C) to the Crossbar Assembly (A) and
secure with mounting balls. Note: The backplate on Fixture Body (C)
should be snug against the wall and the mounting balls. If not, adjust
the length of the mounting screw or alternate short mounting screw
on the Crossbar Assembly (A) by unscrewing the preassembled hex
nut and lock washer and then screwing the mounting screws or
alternate short mounting screws in or out of the crossbar until the
correct length is achieved. Once the backplate on Fixture Body (C)
Lock
Screw is secure, remove the mounting ball and Fixture Body (C) and
proceed to Step 4.
Mounting Screw
Bulb (not
or Alternate Short
Supplied)
Mounting Screw
Socket
D
1of2
.
Supply Wires with
Ground Wire
A
Outlet Box Screws
(not included)
Figure 2
A
Hex Nut and
Lock Washer
Backplate
Figure 3
_R1
C
Mounting
Ball
RevisedDate:2016-06-01