SUMMARY For users ………………………………………………………………………………. P.3-P.9 1. GENERAL INFORMATION 1.1. Contents: 1.2. Operating conditions and range: 1.3. Advantages of different modes: 1.4. Kind reminder: 2. OPERATIONS 2.1. Notice before using 2.2. Operation instructions 2.3. Daily maintenance and winterizing 3. TECHNICAL SPECIFICATION For installers and professionals …………………………………………………...
Page 4
Warning: a. Please read the following tips before installation, use and maintenance. b. Installation, removal and maintenance must be carried in accordance with the instructions. c. Before and after installation, if you detect any gas leakage the unit must be turned off and reported to your supplier.
Page 5
d. If a gas leak is detected during installation all work must stop and be reported to the heat pump supplier for service repair. 3. Transportation & Storage a. Secure load for transportation. b. Care should be taken as not to damage the heat pump during transportation. c.
FOR USER 1. GENERAL INFORMATION 1.1. Contents: After unpacking, please check if you have all the following components. 1.2. Operating conditions and range: ITEMS RANGE Operating range -7℃~43℃ Air temp 18℃~40℃ heating Temp. setting 12℃~30℃ cooling The heat pump will have ideal performance in the operation range Air 15℃~25℃. 1.3.
FOR USER 1.4. Kind MODE RECOMMENDATION ADVANTAGES Heating capacity: 20% to 100% capacity Smart mode Intelligent optimization As standard Fast heating Silence mode Heating capacity: 20% to 80% capacity Use at night Sound level: 3dB (A) lower than Smart mode. reminder: This heat pump has Power-off memory function.
Page 8
FOR USER 1.4.5. Do not use or store combustible gas or liquid such as thinners, paint and fuel to avoid fire. 1.4.6. If any abnormal circumstances occurred, e.g.: abnormal noises, smells, smokes and leakage of electricity, switch off the main power immediately and contact your local dealer. Do not try to repair the heat pump by yourselves.
FOR USER 1.4.9. Please note that following codes are not failure. CODES No water flow Anti-Freezing Reminder Out of the operating temp. range Insufficient water flow or pump blocked Abnormal outdoor power supply 2. OPERATIONS 2.1. Notice before using 2.1.1. The user is advised to start the water pump before the heat pump, and turn off the heat pump before the water pump for long life circle.
Page 10
FOR USER SYMBOL DESIGNATION OPERATION Power ON/OFF Press to power on or off the heat pump Up/ Down Press to set desired water temperature Heat/Cool/Auto Press to shift among cooling, heating and auto Press to select Silence mode ON/OFF Note: You may set the desired water temperature from 12 to 40℃.
FOR USER After entering the Time ON/OFF setting, press directly without adjusting the time to cancel the relevant Timer setting. Exit automatically if no operation for 30 seconds in the Timer ON/OFF mode, 2.2.4 Silence mode The Smart mode as default will be activated when the machine is tuned on. And the display shows ...
FOR INSTALLERS AND PROFESSIONALS 1. TRANSPORTATION 1.1. When storing or moving the heat pump, the heat pump should be at the upright position. 1.2. When moving the heat pump, do not lift the water union since the titanium heat exchanger inside the heat pump will be damaged. 2.
FOR INSTALLERS AND PROFESSIONALS 2.2. Installation instruction 2.2.1. Location and size The heat pump should be installed in a place with good ventilation The picture can't be displayed. * MINIMUM DISTANCE Filter Water switch Water processor...
Page 15
FOR INSTALLERS AND PROFESSIONALS UNIT=MM Summerwave 80Fi Summerwave 100Fi Summerwave 135Fi Summerwave 150Fi Summerwave 175Fi Summerwave 210Fi Summerwave 270Fi 1092 Summerwave 270Fi 1092 Summerwave 350Fi 1161 ※ Above data is subject to m odification w ithout notice. 2.2.2. Heat pump installation.
Page 16
B. For power supply: 400V 50Hz Fuse NOTE: Must be hard wired, no plug allowed (In Australia, Summerwave 80Fi~ Summerwave 135Fi has plug for optional). For your safe use in winter, it’s strongly recommended to equip heating priority function. ...
FOR INSTALLERS AND PROFESSIONALS 2.3. Trial after installation Please check all the wirings carefully before turning on the heat pump. 2.3.1.Inspection before use Check installation of the whole heat pump and the pipe connections according to the pipe connecting drawing; ...
FOR INSTALLERS AND PROFESSIONALS 2.4.2 Winterizing In winter season when you don’t swim, please cut off power supply and drain water out of the heat pump. When using the heat pump under 2℃, make sure there is always water flow. Important: Unscrew the water union of inlet pipe to let the water flow out.
FOR INSTALLERS AND PROFESSIONALS 4. FAILURE CODE DISPLAY NOT FAILURE DESCRIPTION No water protection Power supply excesses operation range Excessive temp difference between inlet and outlet water(Insufficient water flow protection) Ambient temperature too high or too low protection Anti-freezing reminder DISPLAY FAILURE DESCRIPTION High pressure protection...
FOR INSTALLERS AND PROFESSIONALS APPENDIX 3: HEATING PRIORITY WIRING DIAGRAM (OPTIONAL)
Page 23
FOR INSTALLERS AND PROFESSIONALS Parallel connection with filtration clock A: Water pump timer B: Water pump wiring of Heat Pump Note: The installer should connect A parallel with B (as above picture). To start the water pump, condition A or B is connected. To stop the water pump, both A and B should be disconnected.
Page 24
Thank you for choosing Full-inverter Pool heat pump Version: Cb9Ir32...