Advertisement
Quick Links
TBS2603 V2 HDMI Video Encoder User Manual
The steps to setup TBS2603 V2 should be:
1. Connect HDMI Signal to Encoder. The source might come from Setup Box, DVD Player, Tv
Receiver, Camera and ect.
2. Connect Encoder to A Router or a Network Switch.
3. Connect Power Adapter to Encoder. The Standard Power Adapter is DC 12V/2A
4. Configure a new IP for Encoder to adjust your local Network. As Encoder is pre-set a static IP
"192.168.1.168", to login to web UI please make sure your PC/Laptop also has an IP which same
range as Encoder.
Users can manual set an IP "192.168.1.xxx" for PC/Laptop first, and once login to web UI and
change a new IP for Encoder, he can restore PC/Laptop's IP to the default configuration.
web UI login:
Encoder control is web UI, and the recommended Browser is Google Chrome, Fire Box, Microsoft
Edge and ect.
The default web UI Login/password: admin/admin
web UI Preview
web UI has 5 parts:
Home : System status, Input preview, Encode setting, Audio setting and indicates which protocol is
turned on.
Protocols: Configure the output protocols
RTMP: RTMP/RTMPS push configuration
More: OSD Overlay (Text, Logo, Time Code), Video Crop, ROI (Region of Interest)
System:NTP configuration, New IP configuration, FW upgrade, web UI password setting.
The next, let's see more detailed about how to setup TBS2603 V2.
1
Advertisement
Related Manuals for tbs electronics TBS2603 V2
Summary of Contents for tbs electronics TBS2603 V2
- Page 1 RTMP: RTMP/RTMPS push configuration More: OSD Overlay (Text, Logo, Time Code), Video Crop, ROI (Region of Interest) System:NTP configuration, New IP configuration, FW upgrade, web UI password setting. The next, let’s see more detailed about how to setup TBS2603 V2.
- Page 2 Page “Home” System status Normally, for normal encoding and streaming, CPU and RAM will not be over 45%. If ehe value rises abnormally, please have a try cut down the power or have a reset for Encoder. Encode configuration Encoding (Codec) H.264 Baseline/H.264 Main/H.264 High Level 4.2;...
- Page 3 Frame rate. Normally, more “frame rates”, the video will be more smooth. And there’s a trick to setup the frame rate. For example, if your input is 1080p_60hz in, the frame rate better to 60fps or 30fps (same frame rate as the input or a half as the input). This is helpful with the video quality.
- Page 4 The reference relationship of the Single P (Normal P) mode is simple. Each P-frame uses one forward reference frame. The Single P (Normal P) mode can be used in any scenarios. Smart P: In Smart P mode, the P-frame uses the IDR frame (long-term reference frame) and forward reference frame (short-term reference frame) as reference frames.
- Page 5 Audio Encoding (Audio codec): AAC, MP3 AAC: AAC_HE, AAC_LC AAC_HE, the bitrate supports to 128kbps maximum;. And “preview” does not support AAC_HE decoding, if you set Audio Codec to AAC_HE, “Preview” will remind you: Preview is base on video.js player. And also, NDI protocol does not support AAC_HE.
- Page 6 Audio Source: HDMI embedded or Line in HDMI + LINE: HDMI audio and Line in audio mixed up. Protocol (Streaming) It supports: http, rtp/udp Unicast and Multicast, ND | HX2, RTSP, SRT (Caller, Listener), HLS (M3U8). HTTP Stream name: after a new setting, please reboot Encoder to activate. NDI: If you have any changes with the “encode”, for example, “codec”, “resolution”, and etc.
- Page 7 RTSP stream name: also requires to reboot Encoder to activate after new set. SRT: Caller, Listener. Takes Encoder as Caller or Listener. Latency: It's recommended to set the latency 3 to 4 times higher than RTT(round-trip-time). Especially on wireless links such as WLAN, Line-of-Sight Radio (LOS) and mobile links such as LTE/4G or 5G the RTT can vary a lot.
- Page 8 RTMP multiple push: RTMP multiple push to different platforms. For example, the same source “Main stream”, you can push to Youtube, push to Wowza, push to Facebook, Push to Twitch simultaneously. The required syntax is: rtmp://username:password@server:port/appname/playpath if without “username/pwd” authorization, the syntax is: rtmp://server:port/appname/playpath, Or rtmp://server/appname/playpath If you’ll push stream to outside (Internet), your Encoder should be connected to Internet too.
- Page 9 OSD Overlay: Insert “logo”, “text”, “Time code” to Video. HDMI Cut: Video Crop. ROI: Region of Interest. Logo Logo name should be “logo01.bmp, logo02.bmp and ect.”. Logo format should be 24-bit *.bmp”. Logo size please not more than 2MB. X, Y Coordinate: Set the location for logo.
- Page 10 Scrolling: turn on/turn “scrolling” Stepping: the speed of the “scrolling” Direction: scrolling direction, L, R, UP, DOWN Span: Time Code Insert “System clock” to video. HDMI Cut (Video Crop) Left crop, Right Crop, Top crop, Base Crop (Bottom Crop). For Video Crop, It requires to reboot Encoder to activate your configuration. X,Y: to specify the coordinate for the region With, Height: to specify the “Width &...
- Page 11 is to specify the X,Y Coordinates, for instance, location A, X:750, Y:300 is to specify the ROI region, for instance, Width 500, Height 300. ROI region should be: System...
- Page 12 Time Code To set NTP, please make sure your Encoder is connected to Internet, as NTP a is designed to synchronize the clocks of computers over a network. System Upgrade Firmware upgrade. Upload “xx.bin” to upgrade. IP setting. DHCP requires DHCP Server, and requires to reboot Encoder to activate your changes. WIFI Wifi module is not installed in default.
- Page 13 4. If Encoder does not any response, no ping, no web UI enter, no streaming please have a try cut down the power or reset for Encoder, and try again. Any question or doubt about the TBS2603 V2 configuration, please contact with us: support@tbsdtv.com...
Need help?
Do you have a question about the TBS2603 V2 and is the answer not in the manual?
Questions and answers