Advertisement
Quick Links
TBS2603AU HDMI Video Encoder/Decoder User Manual
Preparations:
1. Connect HDMI signal to Encoder
2. Connect LAN cable to Encoder. You can connect Encoder to network switch or a Router.
3. Prepare a PC/Laptop and then power on for your Encoder.
DC 12V: power port. These recommended power adapters are "DC 12V/2A or 5V/2A". DC 12V/1A
adapter is also ok.
Eth: RJ.45 port, 1000M.
Reset: Reset button. Press and hold it around 9 seconds and then release, reset active.
After reset, IP will back to the default 192.168.1.217. And also configuration will back to the
default.
HDMI OUT: Decode and then HDMI out.
HDMI IN: HDMI signal input.
A-OUT: Decode and audio out. Jack 3.5mm.
A-in: Extra audio in (Line in), Jack 3.5mm
LED display: display basic information. Like device IP, input size, CPU consumption and ect.
Encoder control: web UI
Login:
Default username: admin; pwd: admin
1
Advertisement
Related Manuals for tbs electronics TBS2603AU
Summary of Contents for tbs electronics TBS2603AU
- Page 1 TBS2603AU HDMI Video Encoder/Decoder User Manual Preparations: 1. Connect HDMI signal to Encoder 2. Connect LAN cable to Encoder. You can connect Encoder to network switch or a Router. 3. Prepare a PC/Laptop and then power on for your Encoder.
- Page 2 Encoder is pre-set to a static IP “192.168.1.217”, not DHCP to get IP. For the first time, please make sure your PC/Laptop also has an ip which same range as Encoder “19.168.1.xxx”. Two different Devices who have 2 different IP does not support communicating directly. The web UI control is consisted of six parts: Dashboard, Encode, Stream, Overlay, Extend, Options.
- Page 3 Encode: Encode configure. Like video output size, codec, bitrate, GOP, bitrate control, and Network stream Video side: the output size. “auto” means same size as the input. For instance, the input size is 1920x1080, if it’s set to “auto”, the output size will be also 1920x1080. Another, we do not recommend small size in and set to large size out.
- Page 4 Frame rate: Supports to 60fps maximum. More frame rates, video will be more smooth. For this Encoder, the maximum performance/ability is 1-channel 1920x1080p_60hz in and then Encoder to 1-channel 1920x1080p_60fps out. Please to balance the resource for all encode processing. If encode processing out of the maximum performance/ability, Encoder could not work properly.
- Page 5 Choose one or multiple protocols and enable it, and URL will be auto created in “Play URL”: NDI | HX output config: just enable it For NDI | HX stream receiving tools, please try the following: 1. NDI officially provided: https://ndi.tv/tools/ install and launch “Studio Monitor”, then it will auto to detect your Encoder NDI | HX stream 2.Vmix...
- Page 6 Overlay: OSD overlay Add “text, logo, mosaic, time (system time)” to video. If you upload your logo, please make sure logo is “*.png” format, and also the name must be legal. For example, here’s an illegal name “my log.png”, the name contains a “space”. For long name, we recommend you name it to “my_logo.png”.
- Page 7 Extend: extra features Video mix: different media mixed to a same screen. Need to enable “Mix” in page “Encode” first. NDI decode: decode NDI | HX stream Record: record Media and store to USB hard disk. Please prepare a USB hard disk, and it should be FAT32 or EXT4: Multiple push: push to different platforms simultaneously.
- Page 8 Output config: Set the output resolution and source. VGA output is not available, this device does not leave VGA port. Options (system setting): Upgrade firmware: any new firmware release, please upgrade for your Encoder here. Select “*.bin” and upload it. Last, do not forget to reboot Encoder to active the upgrade. Port config: configure port for protocols.
- Page 9 PC/laptop should have an ip which range is 192.168.1.xxx. 2 devices which have different 2 ip ranges, could not communicate directly. So, you can configure an ip 192.168.1.xxx for your PC/Laptop for first time to configure Encoder. Once enter Encoder web GUI, you can change ip to adjust your local network. Encoder IP will display on LED, please check there.
Need help?
Do you have a question about the TBS2603AU and is the answer not in the manual?
Questions and answers