Table of Contents
Advertisement
Quick Links
Operating Instructions
11148001
Valid from:
®
EPIC
CRIMPING TOOL DIGITAL
23.09.2020
®
EPIC
CRIMPING TOOL DIGITAL /
®
EPIC
CRIMPING TOOL DIGITAL SMALL
Operating Instructions
for
11148001
11148004
&
11148300
11148304
11148302
Important notes for the right handling of the
®
EPIC
Four-indent crimping tool
Page 1 of 10
Document: L11148001EN
We reserve all rights according to DIN ISO 16016.
Advertisement
Table of Contents
Related Manuals for LAPP EPIC 11148001 EPIC 11148004
Summary of Contents for LAPP EPIC 11148001 EPIC 11148004
- Page 1 Operating Instructions 11148001 Valid from: ® EPIC CRIMPING TOOL DIGITAL 23.09.2020 ® EPIC CRIMPING TOOL DIGITAL / ® EPIC CRIMPING TOOL DIGITAL SMALL Operating Instructions 11148001 11148004 & 11148300 11148304 11148302 Important notes for the right handling of the ® EPIC Four-indent crimping tool Page 1 of 10...
-
Page 2: Table Of Contents
Operating Instructions 11148001 Valid from: ® EPIC CRIMPING TOOL DIGITAL 23.09.2020 Table of contents 1. General ..........................- 3 - 2. Operation ..........................- 4 - 3. Crimping procedure ......................- 5 - 4. Changing the contact bushing .................... - 5 - 5. -
Page 3: General
Operating Instructions 11148001 Valid from: ® EPIC CRIMPING TOOL DIGITAL 23.09.2020 1. General Your four-indent crimper with a digital display is a hand-crimping tool manufactured using state-of-the-art technology and recognised safety standards. Only use the crimper if it is in perfect working order. Use the four-indent crimper for crimping machined pin and socket contacts, and only for the intended purpose stated in the user manual. -
Page 4: Operation
Operating Instructions 11148001 Valid from: ® EPIC CRIMPING TOOL DIGITAL 23.09.2020 2. Operation Switching on and off Switch the crimper on or off by pressing the ON/OFF switch (7). Select the display Your crimper has a variety of display functions for selection by pressing the recessed MODE switch (6). This allows you to show the crimping stamp setting in mm, inches or the selector positions as given in M22520/7- 01 (not Model 8.76-3). -
Page 5: Crimping Procedure
Operating Instructions 11148001 Valid from: ® EPIC CRIMPING TOOL DIGITAL 23.09.2020 3. Crimping procedure • Feed the prepared cable into the connector • Lay the contact with the cable into the crimper's crimping point until it will not go any further; the contact bushing will position the contact exactly. -
Page 6: Testing Calibration To 1.0 Mm Or 2.0 Mm Using The Gauge
Operating Instructions 11148001 Valid from: ® EPIC CRIMPING TOOL DIGITAL 23.09.2020 7. Testing calibration to 1.0 mm or 2.0 mm using the gauge • Check the default setting of your crimper (1.0 mm or 2.0 mm crimp) before use. • Switch on your crimper by pressing the ON/OFF switch (7). Set to the default setting (1.0 mm or 2 mm) using the adjustment wheel (8). -
Page 7: E1 Message After Calibration Or Recalibration
Operating Instructions 11148001 Valid from: ® EPIC CRIMPING TOOL DIGITAL 23.09.2020 10. E1 message after calibration or recalibration If the crimper display shows an E1 message after several calibration or recalibration attempts (the message will be shown in sequence at irst, then permanently as E1), then the dies in your four-indent crimper are so worn that the wear can no longer be compensated for. -
Page 8: Crimp-Settings
Operating Instructions 11148001 Valid from: ® EPIC CRIMPING TOOL DIGITAL 23.09.2020 14. Crimp-Settings LS1 & M23 Contacts: (11148001+11148300) Contact Settings Type Art. No. Adjustment wheel Locator LS 1 A6 44420104 4,00 1,55 44420105 2 mm female hyperboloid contact 0,50 1,15 LS 1 A6 0,75 1,20... - Page 9 Operating Instructions 11148001 Valid from: ® EPIC CRIMPING TOOL DIGITAL 23.09.2020 D-Sub contacts (11148004+11148302) contact Settings Type Art. No. Adjustment Locator wheel 0,25 1,00 D-Sub 0,34 1,05 44423357 0,50 1,10 1 mm male contact 0,75 1,15 1,00 1,20 0,25 1,00 D-Sub 0,34 1,05...
- Page 10 Operating Instructions 11148001 Valid from: ® EPIC CRIMPING TOOL DIGITAL 23.09.2020 M17 contacts (11148004+11148304) Page 10 of 10 Document: L11148001EN We reserve all rights according to DIN ISO 16016.