USER’S MANUAL MANUFACTURE AND SERVICE HYDRAULIC AUTOMOBILE LIFT Model: Serial No.: Year of Manufacture: Manufacturer: Name: Address: Tel: Fax: Http: AUTHORISED SERVICE CENTRE:...
USER’S MANUAL CONTENTS Contents Manufacture and service Packing, transport and storage Introduction l Description of the machine l Technical specifications l Safety l Installation l Adjustment l Operation l Maintenance and care l Troubleshooting l Accessory...
USER’S MANUAL PACKING, TRANSPORT AND STORAGE PACKING (Picture 1) Picture 1 TRANSPORT (Picture 2) Packing can be lifted or moved by lift trucks, cranes or bridge cranes. In case of slinging, a second person must always take care of the load, in order to avoid dangerous oscillations.
USER’S MANUAL INTRODUCTION This manual has been prepared for workshop personnel expert in the use of the lift operator and technicians responsible for routine maintenance fitter. Workers should read the ‘Maintenance & User Manual’ carefully before carrying out any operation with the lift. This manual contains important information regarding: The personal safety of operators and maintenance workers.
USER’S MANUAL Chapter 1 DESCRIPTION OF THE MACHINE Machine Application: This lift can lift each kind of vehicle which weight is not over 2800kg, and is suitable for use in vehicle tests, maintenance, and caring for automobiles, which is particularly suitable for use in the basement or on the floor without hole.
Page 7
USER’S MANUAL Chapter 2 SPECIFICATION Main technical parameter Machine type 2.8HS Drive Electrical hydraulic Lifting weight 2800kg Lifting height 1300mm Platform initial height 105mm Platform length 1800mm Platform width 1040mm Lifting time ≤50s Descent time ≤60s Whole machine length 1800mm Whole machine width 1330 mm Weight...
Page 8
USER’S MANUAL Chapter 2 SPECIFICATION Lift dimension picture: Picture 4 Motor Pump Type………………………MS90L Type……………………………P1.7 Power……………… 2.2kw Model…………………………gear pump Voltage……………AC 400 or 230V Max flux…………………………1.7cc/r ±5% Joint type………………………direct joint Power supply…………… 400VAC:20A ………………230V:40A Overflow valve Max Frequency………50Hz (optional Setting pressure………………280 bar choose 60HZ) Adjustable working...
Page 9
USER’S MANUAL Chapter 2 SPECIFICATION Supply at the same time -Connect to the power supply jack of control box (400V or 230V) Requirements: -Concrete type 425#, the period of desiccation is 15 days. -Clean the basic layer, thickness of concrete≥150mm, the leveling of whole length≤ 5mm.
Page 10
USER’S MANUAL Chapter 3 SAFETY Read this chapter carefully and completely since important information for the safety of the operator or others in case of improper use of the lift is included. In the following text there are clear explanations regarding certain situations of risk or danger that may arise during the operation or maintenance of the lift, the safety device installed and the correct use of such systems, residual risks and operative procedures to use (general specific precautions to eliminate potential...
Page 11
USER’S MANUAL Chapter 3 SAFETY GENERAL PRECAUTIONS The operator and the maintenance fitter are required to observe the prescriptions of safety regulation in force in the country of installation of the lift. Furthermore, the operator and maintenance fitter must: -Always work in the stations specified and illustrated in this manual; -Never remove or deactivate the guards and mechanical, electrical, or other types of safety devices;...
Page 12
USER’S MANUAL engine failure. In the condition of over loading, the overflow valve will open and directly return oil to the oil tank. (See Picture 8) Chapter 3 SAFETY Each bottom of oil cylinder is equipped with antiknock valve. When the oil pipe is burst in the circuit of hydraulic pressure, the relevant antiknock valve will work and limit the speediness of platform.
Page 13
USER’S MANUAL that are not compatible with the capacity of the lift. When the platform is being tested, the vehicle engine cannot be turned on. There is nothing should be placed on the lift-lowering area and the movable parts of the lift. Chapter 3 SAFETY RISK OF SLIPPING (Picture 12) The floor caused by lubricant contamination of around the lift.
Page 14
USER’S MANUAL Chapter 4 INSTALLATION SKILLED AUTHORIZED PERSONNEL ONLY SHOULD ALLOWED TO PERFORM THESE OPERATIONS, FOLLOW ALL INSTRUCTIONS SHOWN BELOW CAREFULLY, IN ORDER TO PREVENT POSSIBLE DAMAGE TO THE CAR LIFT OR RISK OF INJURY TO PEOPLE. Skilled technicians only appointed by the same manufacturer or by authorized dealers, are allowed to install the car lift.
Page 15
USER’S MANUAL Chapter 4 INSTALLATION Platform Installation: -Place the platforms on the position of the location. -The bottom of hydraulic cylinder is located in the frontage of machine (the direction of driving on the vehicle) -Use fork lift or other lifting equipments to lift the platform (Picture 15) and insert a wood in the middle part of joint pole.
Page 16
USER’S MANUAL Chapter 4 INSTALLATION Oil PIPE CONNECTION: Follow “oil pipe diagram “to connect the oil pipes. Only skilled and authorized person is allowed to perform the operations. And pay particularly attention to the protection of oil pipe fitting. -Following oil pipe number to lead the oil pipe from control box to the cylinder. (Refer to “oil pipe diagram”) -When connecting oil pipes, pay attention to the protection of oil pipe tie-in to prevent impurities from entering hydraulic circuit.
Page 17
USER’S MANUAL Chapter 5 ADJUSTMENT Add oil and check the order of phase. After installing lift as Picture 4 required and connecting hydraulic circuit and electric circuit, operate it as following: -open the hydraulic oil tank, add 12L of hydraulic oil into the oil tank, the hydraulic oil is provided by the user.
USER’S MANUAL Chapter 6 OPERATION Only skilled and having been trained personnel is allowed to perform the operations. Check proceedings as following. Operation Notices: -Clear obstacles around the lift before operation. -During lifting or lowering, no person is allowed to stand near the two sides and beneath the machine, and no person is allowed on the two platforms.
USER’S MANUAL The machine should be lower to the lowest position when replace hydraulic oil, then let the old oil out, and should be filtering the hydraulic oil. -Each team checks the agility and reliability of pneumatic safety equipment. Chapter 8 TROUBLESHOOTING Skilled personnel only are allowed to perform the operations.
USER’S MANUAL the demolition must be disposed of in accordance with the current standards of the country in which the rack is installed. Finally, it should be recalled that for tax purposes, demolition must be documented; submitting claims and documents according to the current laws in the country in which the rack is installed at the time the machine is demolished.
Page 21
USER’S MANUAL ACCESSORY Oil pipe connection diagram A Descent valve B Valve core of descent valve C Loop of descent valve D motor E Overflowing valve F Motor wiring box G Oil hose...
Need help?
Do you have a question about the 9831 and is the answer not in the manual?
Questions and answers