Advertisement
Manufacturer / distributor:
VacuumChambers.eu
drControl Dawid Roszczenko
Jodłowa 3A/34
16-001 Ignatki-Osiedle
Poland
E-mail: shop@vacuumchambers.eu; Telephone: +48535312207
BEFORE USING, PLEASE READ THIS USER MANUAL. Keep the manual for possible future use, as it may always
be necessary to remember the information contained in the manual, and it must be provided with the device
in the event of reselling the machine or changing the user.
WARNING! In order to avoid the risk of injuries and accidents, as well as to increase work efficiency and
prevent premature wear of the device, read all warnings, safety instructions and paragraphs marked with the
symbol:
Do not dispose of that product as unsorted municipal waste.
Used equipment should be sent to an electro-waste collection point.
Nature friendly company.
All photos used in this manual are illustrative photos. The appearance and quantity of the elements supplied to the
customer, as well as their mutual location may vary depending on the ordered vacuum set.
This user manual is based on current knowledge and experience. The manufacturer reserves the right to change the content
of this manual without informing the consumer.
Contents
................................................................................................................................................................ 3
...................................................................................................................................................... 3
........................................................................................................................................... 3
.................................................................................................................................................................... 4
Air manifold assembly. ..................................................................................................................................................... 4
Preparation of the vacuum pump. ................................................................................................................................... 6
Connection of elements of the vacuum set. .................................................................................................................... 6
................................................................................................................................................................ 7
Fitting muffler. ...................................................................................................................................................................... 7
Vacuum feedthrough with pouring hose and mechanical flow controller. ........................................................................ 7
Stirrer mechanism. ................................................................................................................................................................ 8
Vacuum trap. ....................................................................................................................................................................... 10
E.
Vacuum cold trap. ............................................................................................................................................................... 11
.................................................................................................................................................................... 14
...................................................................................................................................................................... 14
................................................................................................................................................ 15
........................................................................................................................................................................... 16
A.
Tank gasket replacement. .............................................................................................................................................. 16
................................................................................................................................................................................. 16
................................................................................................................................................... 17
2
Advertisement
Table of Contents
Related Manuals for VacuumChambers VC4550SSG
Summary of Contents for VacuumChambers VC4550SSG
-
Page 1: Table Of Contents
Vacuum trap..................................10 Vacuum cold trap................................11 ..................................14 ..................................14 ..............................15 Manufacturer / distributor: ................................... 16 VacuumChambers.eu Tank gasket replacement............................... 16 drControl Dawid Roszczenko Jodłowa 3A/34 ....................................16 16-001 Ignatki-Osiedle ..............................17 Poland E-mail: shop@vacuumchambers.eu; Telephone: +48535312207... -
Page 2: Air Manifold Assembly
Vacuum sets are used in the process of degassing casting materials such as silicone, resin, gypsum and the process of impregnation of wood and other porous materials. The vacuum chamber is a sealed tank inside of which it is possible to create a low pressure environment by the suction of contained gases by the vacuum pump. -
Page 3: Preparation Of The Vacuum Pump
B. Preparation of the vacuum pump. washer and nut O-ring 1) Before the first use necessarily fill the vacuum pump (Photo 7) with the oil provided with the set. To do that, place the pump on the flat, horizontal surface, unscrew the red plug (1) and pour the oil through the oil feed hole. For some models of pumps (when there is no red cap), the oil should be poured through the hole in the pump housing after the blue oil filter cylinder (2) has been unscrewed. -
Page 4: Fitting Muffler
It is recommended to connect the vacuum set only with parts and products supplied by VacuumChambers.eu. If the customer connects the vacuum set or its parts with elements or devices from other manufacturers, the customer is solely responsible for the appropriate selection of these elements, their compatibility and quality of their connection. -
Page 5: Vacuum Trap
The lid is made of stainless steel. The agitator is ended with an ISO metric screw thread (M14), which allows it to be screwed If it is difficult or impossible to close at least one clamp, make sure that the lid is correctly positioned. If necessary, the into the coupling (3). - Page 6 Vacuum cold trap. from the inner tank, as their accumulation may result in dangerous pressure build-up in the inner tank. Therefore, the inner tank lid must not be loaded with other objects, nor have limited free lift. The inner tank should not be tightly closed. After placing the A vacuum cold trap is a type of vacuum chamber.
- Page 7 When operating vacuum pumps that do not come from the VacuumChambers.eu offer, please refer to the operating 14) Handle the remaining cooling agent in accordance with its safety instructions. instructions supplied with the pump by the manufacturer.
- Page 8 Do not use the device or any of its parts for purposes other than those for which it was intended. Do not make any from the breakdown of this product. In the case of a claim, VacuumChambers.eu's sole responsibility is to accept a return or modifications or changes to the vacuum set or its individual components.
Need help?
Do you have a question about the VC4550SSG and is the answer not in the manual?
Questions and answers