Advertisement
Operation Guide 2971
• Time calibration signal reception takes from two to six minutes. Take care that you
do not perform any button operations or move the watch during this time.
600 miles
• Under good reception conditions, signal reception is possible within a radius of
about 2,000 miles (3,000 kilometers) from the Fort Collins transmitter.
• At distances further than about 600 miles (1,000 kilometers) from the transmitter,
signal reception may not be possible during certain times of year or times of day.
Radio interferance may also cause problems with reception.
• See the information under "Signal Receive Troubleshooting" if you experience
problems with time calibration signal reception.
About Auto Receive
When auto receive is turned on, the watch starts to receive the time calibration signal
automatically when the time in the Timekeeping Mode reaches midnight, 1:00 a.m.
and 2:00 a.m. (calibration times).
If both the 1 o'clock and 2 o'clock signal receptions are not successful, the watch will
try to receive the signal again at the top of each hour up until 5:00 a.m. or until one
more reception is successful.
Note
• Auto receive works only while the watch is in the Timekeeping Mode or World Time
Mode. Auto receive is not performed if an auto receive time is reached while an
alarm is sounding, while a countdown timer operation is in progress, or if a setting
screen (a screen with a flashing setting) is on the display.
• Auto receipt of the calibration signal is designed to be performed early in the
morning, while you sleep (provided that the Timekeeping Mode time is set correctly).
Before going to bed for the night, remove the watch from your wrist, and put it in a
location where it can receive the signal easily.
• When auto receive is turned on, the watch receives the calibration signal for two to
six minutes everyday when the Timekeeping Mode time reaches each of the
calibration times. Do not perform any button operation within six minutes before or
after any one of the calibration times. Doing so can interfere with correct calibration.
• Remember that reception of the calibration signal depends on the time kept in the
Timekeeping Mode. The receive operation will be performed whenever the display
shows any one of the calibration times, regardless of whether or not the
Timekeeping Mode time is actually the correct time.
• If more than one auto receive is successful, the watch uses the data from the last
successful receive to adjust settings. When only one reception is successful, the
watch uses the data of the successful reception.
About the Receiving Indicator
The receiving indicator shows the strength of the calibration signal being received. For
best reception, be sure to keep the watch in a location where signal strength is
strongest.
Receiving indicator
Weak
(Level 1)
• Even in an area where signal strength is strong, it takes about 10 seconds for signal
reception to stabilize enough for the receiving indicator to indicate signal strength.
• Use the receiving indicator as a guide for checking signal strength and for finding the
best location for the watch during signal receive operations.
• Following reception of the time calibration signal and calibration of the watch's time
setting, the Level 4 receiving indicator will remain on the display in all modes. The
Level 4 receiving indicator will not be displayed if signal reception was unsuccessful
or after you adjust the current time setting manually.
• The Level 4 receiving indicator is displayed only when the watch is able to receive
both time and date data successfully. It does not appear when only time data is
received.
• The Level 4 receiving indicator indicates that at least one of the auto calibration
signal receive operations was successful. Note, however, that the Level 4 receiving
indicator is cleared from the display at 1:00 a.m. each day.
To perform manual receive
1. Place the watch on a stable surface so its top (12
o'clock side) is facing towards a window.
Receiving indicator
2. In the Timekeeping Mode, hold down D for about two
seconds until the watch beeps.
• Release D and the message RC! appears to indicate
that signal reception has started.
• Time calibration signal reception takes from two to six
minutes. Take care that you do not perform any button
operations or move the watch during this time.
• After signal reception is complete, the display of the
watch changes to the Last Signal screen.
Note
• To interrupt a receive operation and return to the Timekeeping Mode, press D.
• If the receive operation is unsuccessful, the message
for about one or two minutes. After that, the watch returns to the Timekeeping Mode.
• You can also change from the Last Signal or
timekeeping screen by pressing D.
2,000 miles
Fort Collins
Strong
(Level 4)
ERR
appears on the display
ERR
screen to the normal
To turn auto receive on and off
1. In the Timekeeping Mode, press D to display the Last
Signal screen.
On/Off Status
2. Hold down A until the receiving indicator and current
auto receive setting (
is the setting screen.
• Note that the setting screen will not appear if the
currently selected Home City is one that does not
support time calibration reception.
3. Press D to toggle auto receive on (
4. Press A to exit the setting screen.
• For information about city codes that support signal
receive, see "To set your Home City".
To display the Last Signal screen
In the Timekeeping Mode, press D to display the Last Signal screen (indicated by
GET
). The Last Signal screen shows the date and time of the last successful time
calibration signal reception.
Month – Day
PM
indicator
Press D.
Hour : Minutes Seconds
Signal Receive Troubleshooting
Check the following points whenever you experience problems with calibration signal
reception.
Problem
Probable Cause
• The watch is not in the Timekeeping Mode.
Cannot perform
• Your current Home City is not one of the
manual receive.
following city codes:
LAX, DEN, CHI, or NYC.
• You changed the time setting manually.
Auto receive is
• The watch was not in the Timekeeping
turned on, but
or World Time Mode, or you performed
the Level 4
some button operation during the auto
receiving
receive operation.
indicator does
not appear on
the display.
• Even if receive is successful, the Level 4
Auto receive is
turned on, but
receiving indicator disappears every day
the Level 4
at 1 am.
• Time data (hour, minutes, seconds) only
receiving
indicator does
was received during the last receive
not appear on
operation. The Level 4 receiving
the display.
indicator appears only when time data
and date data (year, month, day) are
both received.
• If the time is one hour off, the DST
Time setting is
incorrect
setting may be incorrect.
• The Home City code setting is not
following signal
reception.
correct for the area where you are using
the watch.
• For further information, see "Important!" under "Time Calibration Signal Reception"
and "Radio-controlled Atomic Timekeeping Precautions".
World Time
The World Time Mode shows you the current time in 30
City code
cities (29 time zones) around the world.
• If the current time shown for a city is wrong, check your
Home City time settings and make the necessary
changes.
• All of the operations in this section are performed in the
World Time Mode, which you enter by pressing C.
Current time in selected city
To view the time in another city
While in the World Time Mode, press D to scroll eastward through the city codes
(time zones) or B to scroll westward.
• For full information on city codes, see the "City Code Table".
To toggle a city code time between Standard Time and Daylight Saving Time
1. In the World Time Mode, use B and D to display the
DST indicator
city code (time zone) whose Standard Time/Daylight
Saving Time setting you want to change.
2. Hold down A to toggle Daylight Saving Time (DST
indicator displayed) and Standard Time (DST indicator
not displayed).
• Note that you cannot switch between Standard Time
and Daylight Saving Time while
city code.
• The DST indicator will appear whenever you display a
city code for which Daylight Saving Time is turned on.
• Note that the DST/Standard Time setting affects only the
currently displayed city code. Other city codes are not
affected.
ON
or
OFF
) start to flash. This
ON
) and off (
OFF
).
Last Signal Screen
Receive time
Receive date
What you should do
• Enter the Timekeeping Mode
and try again.
• Select LAX, DEN, CHI, or
NYC as your Home City.
• Perform manual signal receive
or wait until the next auto
signal receive operation is
performed.
• Perform manual signal
receive or wait until the next
auto signal receive operation
is performed.
• Check to make sure the
watch is in a location where it
can receive the signal.
• Change the DST setting to
Auto DST.
• Select the correct Home City
code.
GMT
is selected as the
2
Advertisement
