Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for LMI Technologies Gocator 200 Series
Summary of Contents for LMI Technologies Gocator 200 Series
- Page 1 20 0 Series and Lig ht Bar Quick St art Guid e...
- Page 2 Gocator 200 Quick Start Guide This document provides initial setup instructions for Gocator 200 series scanners, as well as the Gocator 205 color vision module and Gocator light bars. For detailed information, see the user manual. Gocator 200 Series and Light Bar Quick Start Guide...
-
Page 3: Device Overview
Device Overview Gocator 200 Series Gocator 200 series scanners are designed with a unique clearance distance (CD), measurement range (MR), and field of view (FOV). For more information about your model see the user manual. Gocator 200 series scanners are transverse scanning devices. - Page 4 Provide power for up to two light bars. Connect a Light Bar to Gocator 205 cordset to this connector. Power Indicator Illuminates when power is applied (blue). Serial Number Unique serial number. Gocator 200 Series and Light Bar Quick Start Guide...
-
Page 5: Laser Safety
This product is designated for use solely as a component and as such it does not fully comply Gocator 200 Series and Light Bar Quick Start Guide... -
Page 6: Laser Radiation
Use shielded cables with shield grounded at both ends. Sensor housing should be connected to earth ground. Use a suitable power supply The +24-48V power supply used with Gocator sensors should be an isolated supply with inrush current protection. Use care when handling powered devices Gocator 200 Series and Light Bar Quick Start Guide... -
Page 7: Installation
Scanners should not be installed near objects that might occlude a camera's view of the projected light. Scanners should not be installed near surfaces that might create unanticipated light reflections. Gocator 200 Series and Light Bar Quick Start Guide... - Page 8 The following shows how a Gocator 205 and a light bar mount to a Gocator 200 series scanner. Light bar to Gocator 205 mounting hardware is optional.
- Page 9 Standalone systems are typically used when only a single sensor is required. The device can be connected to a computer's Ethernet port for setup and can also be connected to devices such as encoders, photocells, or PLCs. Standalone systems are not typically used in wood applications. Gocator 200 Series and Light Bar Quick Start Guide...
- Page 10 Sensors and client computers communicate via an Ethernet switch (1 Gigabit/s recommended). Multi-sensor Gocator 200 systems can only be configured using GoSDK. For more information, see GoSDK and GoWebScanSDK in the Gocator 200 Series user manual. Gocator 200 Series and Light Bar Quick Start Guide...
- Page 11 View: Looking into the connector on the sensor Safety+ Blue/Black Blue/Red Sync+ White/Brown & Brown/Red Black Sync- Brown/Black Brown/Black Ethernet MX1+ White/Orange White/Orange Ethernet MX1- Orange Orange Ethernet MX2+ White/Green White/Green Ethernet MX2- Green Green Gocator 200 Series and Light Bar Quick Start Guide...
- Page 12 White / Blue & Black Reserved Green Gray / Red Reserved Yellow & Maroon Gray / Black / White & Orange / Black Reserved Maroon Orange / Red (not connected) (not connected) Gocator 200 Series and Light Bar Quick Start Guide...
- Page 13 Click Advanced, click Hardware, click the Configure pop-up menu, and set it to “Manually”. Enter IP Address “192.168.1.5” and Subnet Mask “255.255.255.0”, and then click Apply. Step 2 Open a web browser and enter the default sensor address. The Gocator interface loads. Gocator 200 Series and Light Bar Quick Start Guide...
- Page 14 In your browser, ensure that Replay mode is off (slider set to left) and that the Laser Safety switch is enabled or the Laser Safety input is high. Step 2 Switch to the Scan or Measure page. Gocator 200 Series and Light Bar Quick Start Guide...
- Page 15 This product is designed solely as a component and as such it does not comply with the standards relating to laser products specified in U.S. FDA CFR Title 21 Part 1040. Contact LMI Technologies has sales offices and distributors worldwide. All contact information is listed at https://lmi3d.com/contact/. Gocator 200 Series and Light Bar Quick Start Guide...