FlySky FS-WTM01 Manual

产品介绍 Introduction
感谢您购买富斯无线教练模块，选用本模块，就可以实现教练机与
学员机无线连接，让您省却配备专门的教练线，感受更多乐趣。
产品概览 Overview
[1] [2]
[5]
54321
产品规格 Specifications
产品型号：FS-WTM01
适配遥控器：PL18
通道个数：18
无线频率：2.4GHz ISM
无线协议：AFHDS 2A/AFHDS3
天线类型：内置天线
遥控距离：>50 米
USB 接口供电范围：3.5 ～ 9V
功率：<13dBm
数据输出类型：PPM
温度范围：-10℃ ~ +60℃
湿度范围：20% ~ 95％
在线更新：有
外形尺寸：42.2mm*18mm*6.6mm
重量：4.5g
认证：CE、FCC ID: N4ZWTM0100
接口介绍 Interface introduction
本无线教练模块设有 USB 接口和蓝牙接口。
USB 接口
无线教练模块通过 USB 接口，既可以实现为本模块供电，又可以实现教练功能。
• USB 接口供电：需要搭配富斯公司的 FS-XC002、FS-XC003 或 FS-XC004 线缆实
现通过 USB 接口供电 ，这三款线缆都配有电源接口，通过此接口为模块供电。
蓝牙接口
无线教练模块通过蓝牙接口与遥控器相连接，实现通道数据传输，还可以通过遥控
器主界面查看本模块相关信息等。
• 蓝牙接口供电：将无线教练模块连接遥控器的蓝牙接口。
注：（1）USB 接口供电与蓝牙接口独立供电，优先选用蓝牙供电。
（2）若不使用蓝牙接口时，请不要取下蓝牙接口保护帽，以保护蓝牙接口。
连接 PL18 蓝牙接口参考示意图如下：
http://www.flysky-cn.com
Copyright ©2021 Flysky Technology co., ltd
FS-WTM01
Thank you for purchasing Flysky wireless trainer unit. By choosing this unit, you can
realize the wireless connection between trainer transmitter and student transmitter. In
this way, the special trainer cable is not required.
[1] USB 接口
[3] [4]
[2] LED 指示灯
[3] 信号接头
[4] 信号接头保护帽
[5] 三档开关（ AFHDS 2A/AFHDS3/UPD）
1、电源正极
2、信号输出端 1
3、信号输出端 2
4、 /
5、 电源负极
Wireless trainer unit
[1] Micro USB
[2] LED
[3] Bluetooth port
[4] Protective cover
[5] Three-level switch (AFHDS 2A/AFHDS3/UPD）
1、Power anode
2、Signal 1
3、Signal 2
4、 /
5、 Power cathode
Product Name: FS-WTM01
Adaptive transmitter: PL18
Channels: 18
RF: 2.4GHz ISM
Protocol: AFHDS 2A/AFHDS3
Antenna: Built-in antenna
Distance: >50m
Input power: 3.5 ～ 9V
Maximum Power: <13dBm(E.I.R.P.) (EU)
Data Output: PPM
Temperature Range: -10℃ ~ +60℃
Humidity Limit: 20% ~ 95%
Online Update: Yes
Dimensions: 42.2mm*18mm*6.6mm
Weight: 4.5g
Certification: CE, FCC ID: N4ZWTM0100
This wireless trainer unit has the micro USB interface and
Bluetooth port.
Micro USB interface
The wireless trainer unit can realize both power supply and
trainer function through this micro USB interface.
• Power supply through the micro USB interface: Flysky FS-
XC002, FS-XC003 or FS-XC004 cables are required to realize
power supply through the micro USB interface. All three
cables are equipped with the power supply interface. The
supply power for the unit is implemented through this
interface.
Bluetooth Port
The wireless trainer unit is connected to the transmitter
through the Bluetooth port to transfer channel datas. You
can view the information related to the unit on the main
interface of the transmitter.
• Power supply through the Bluetooth port: Connect the
wireless trainer unit to the Bluetooth port of the transmitter.
Notes: (1) The power supply of the micro USB interface and
Bluetooth port is provided independently. The Bluetooth
power supply is preferred.
(2) If you don't use the Bluetooth port, please don't
take off the Bluetooth port protective cover. This is for the
protection of the Bluetooth port.
Connecting to the Bluetooth port of PL18 is showing on the
left, for your reference.