ABB HT565485 Operation Manual page 139

Operation Manual / 4 Product description / A100-L
Figures
Figures
Fig. 1 Layout and function of the tur-
bocharger ..................................
Fig. 2 Warning plate locations .............
Fig. 3 Locations of the rating plates .....
Fig. 4 Fitting lifting gear to turbo-
charger ...................................... 12
Fig. 5 Placing the turbocharger on the
bracket ....................................... 13
Fig. 6 Compressor-end foot ................. 14
Fig. 7 Turbine-end foot ........................ 14
Fig. 8 Layout and overview of the
speed measurement system ...... 23
Fig. 9 Replacing the speed sensor ...... 25
Fig. 10 U-tube manometer at the filter
silencer ...................................... 27
Fig. 11 Noise insulation, bellows ........... 30
Fig. 12 Layout and overview of filter
silencer ...................................... 38
Fig. 13 Dismantling filter ring circumfer-
ential part ................................... 40
Fig. 14 Opening filter ring lock ............... 40
Fig. 15 Attaching new filter ring ............. 41
Fig. 16 Fitting new filter ring ................... 41
Fig. 17 Overview of wet cleaning of
compressor ................................ 44
Fig. 18 Filter plug view ........................... 45
Fig. 19 Overview of dry cleaning device
Fig. 20 Drain pipe diagram .................... 50
Fig. 21 Overview of assembly weights .. 59
Fig. 22 Overview of filter silencer cas-
ing disassembly and assembly .. 60
Fig. 23 Fitting filter silencer casing 1 ..... 61
Fig. 24 Fitting filter silencer casing 2 ..... 62
Fig. 25 Fitting filter silencer casing 3 ..... 62
Fig. 26 Fitting filter silencer casing 4 ..... 63
Fig. 27 Fitting filter silencer casing 5 ..... 63
Fig. 28 Fitting the bellows ...................... 64
Fig. 29 Dismantling the filter silencer ..... 65
Fig. 30 Dismantling the filter silencer
with noise package .................... 66
© Copyright 2016 ABB. All rights reserved.
Fig. 31 Pressing off compressor casing
6
Fig. 32 Moving out wall insert ................
8
Fig. 33 Putting down wall insert .............
9
Fig. 34 Putting down wall insert .............
Fig. 35 Dismantling the diffuser ............
Fig. 36 Measuring axial clearance A .....
Fig. 37 Removing the insulation
(A175-L and smaller). ................
Fig. 38 Dismantling the gas inlet casing
(A175-L and smaller) .................
Fig. 39 Dismantling the nozzle ring
(A175-L and smaller) .................
Fig. 40 Dismantling the gas inlet casing
(A180-L and larger) ...................
Fig. 41 Fitting the nozzle ring holder .....
Fig. 42 Dismantling the nozzle ring
(A180-L and larger) ...................
Fig. 43 Putting down the nozzle ring
(A180-L and larger) ...................
Fig. 44 Fitting the nozzle ring (A175-L
and smaller) ...............................
Fig. 45 Fitting the gas outlet casing
(A175-L and smaller) .................
Fig. 46 Fit insulation. .............................
Fig. 47 Looping around the nozzle ring
(A180-L and larger) ...................
Fig. 48 Fitting the nozzle ring (2)
47
(A180-L and larger) ...................
Fig. 49 Fitting the gas inlet casing
(A180-L and larger) ...................
Fig. 50 Measuring axial clearance A .....
Fig. 51 Fitting the diffuser ......................
Fig. 52 Positioning wall insert ................
Fig. 53 Fitting the wall insert .................
Fig. 54 Fitting the filter silencer .............
Fig. 55 Fitting the filter silencer with
noise package ...........................
Fig. 56 Overview of tightening torques ..
Fig. 57 Overview of speed sensor tight-
ening torque ..............................
HZTL4034_EN
Page 109 / 111
Revision G
October 2016
67
68
68
69
70
71
72
73
73
74
75
76
76
77
78
79
80
81
82
83
84
85
86
87
88
90
90