HQ Power VDP1000SW Manual

1000w dmx-controlled snow machine
Table of Contents
  • Algemene Richtlijnen
  • Reiniging en Onderhoud
  • Technische Specificaties
  • Prescriptions de Sécurité
  • Directives Générales
  • Nettoyage Et Entretien
  • Spécifications Techniques
  • Instrucciones de Seguridad
  • Normas Generales
  • Instalación
  • Limpieza y Mantenimiento
  • Especificaciones
  • Einführung & Eigenschaften
  • Allgemeine Richtlinien
  • Betrieb
  • Wartung und Pflege
  • Technische Daten

Advertisement

Available languages
  • EN

Available languages

  • ENGLISH, page 1

Quick Links

VDP1000SW – 1000W DMX-CONTROLLED SNOW MACHINE
1. Introduction & Features
To all residents of the European Union
Important environmental information about this product
This symbol on the device or the package indicates that disposal of the device after its lifecycle could harm
the environment.
Do not dispose of the unit (or batteries) as unsorted municipal waste; it should be taken to a specialised
company for recycling.
This device should be returned to your distributor or to a local recycling service.
Respect the local environmental rules.
If in doubt, contact your local waste disposal authorities.
Thank you for buying the VDP1000SW! Please read the manual thoroughly before bringing this device into service.
If the device was damaged in transit, don't install or use it and contact your dealer.
2. Safety Instructions
Be very careful during the installation: touching live wires can cause life-threatening electroshocks.
Keep this device away from rain and moisture.
Unplug the mains lead before opening the housing.
• Damage caused by disregard of certain guidelines in this manual is not covered by the warranty and the dealer
will not accept responsibility for any ensuing defects or problems.
• A qualified technician should install and service this device.
• Do not switch the device on immediately after it has been exposed to changes in temperature. Protect the device
against damage by leaving it switched off until it has reached room temperature.
• This device falls under protection class I. It is therefore essential that the device be earthed. Have a qualified
person carry out the electric connection.
• Make sure that the available voltage does not exceed the voltage stated in the specifications of this manual.
• Do not crimp the power cord and protect it against damage. Have an authorised dealer replace it if necessary.
• Disconnect the device from the mains to clean it or when it is not in use. Handle the power cord by the plug only.
• Note that damage caused by user modifications to the device is not covered by the warranty.
• Keep the device away from children and unauthorised users.
3. General Guidelines
• This device is designed for professional use on stage, in discos, theatres, etc. The VDP1000SW should only be
used indoors with an alternating current of max. 230VAC / 50Hz.
• This effect is not designed for permanent operation: regular operation breaks will prolong their lives.
• Do not shake the device. Avoid brute force when installing or operating the device.
• Select a location where the device is protected against extreme heat (see "Technical Specifications"), dust and
moisture.
• Familiarise yourself with the functions of the device before actually using it. Do not allow operation by unqualified
people. Any damage that may occur will most probably be due to unprofessional use of the device.
• Use the original packaging if the device is to be transported.
• All modifications of the device are forbidden for safety reasons.
• Only use the device for its intended purpose. All other uses may lead to short circuits, burns, electroshocks,
crash, etc. Using the device in an unauthorised way will void the warranty.
VDP1000SW
1
VELLEMAN

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the VDP1000SW and is the answer not in the manual?

Questions and answers

Summary of Contents for HQ Power VDP1000SW

  • Page 1 • Keep the device away from children and unauthorised users. 3. General Guidelines • This device is designed for professional use on stage, in discos, theatres, etc. The VDP1000SW should only be used indoors with an alternating current of max. 230VAC / 50Hz.
  • Page 2: Installation

    Connect the provided XLR cable to the female 3-pin XLR output of your controller and the other side to the male 3- pin XLR input of the VDP1000SW. Multiple VDP1000SWs can be linked through serial linking. The linking cable should be a two-core screened cable with XLR input and output connectors. Please refer to the diagram.
  • Page 3: Cleaning And Maintenance

    In the case of the 1-channel VDP1000SW, you will have to set the start address of the first VDP1000SW to 1, the second VDP1000SW to 2 (1 + 1), the third to 3 (1 + 1) and so on.
  • Page 4: Algemene Richtlijnen

    VDP1000SW – DMX-GESTUURDE SNEEUWMACHINE 1000W 1. Inleiding en kenmerken Aan alle ingezetenen van de Europese Unie Belangrijke milieu-informatie betreffende dit product Dit symbool op het toestel of de verpakking geeft aan dat, als het na zijn levenscyclus wordt weggeworpen, dit toestel schade kan toebrengen aan het milieu.
  • Page 5 Alle DMX-gestuurde toestellen hebben een digitaal startadres nodig, zodat het juiste toestel reageert op de signalen. Dit digitale startadres is het kanaalnummer van waarop het toestel “luistert” naar het signaal van de DMX controller. Geef het correcte nummer in en lees het af op de display onderaan uw VDP1000SW. VDP1000SW...
  • Page 6: Reiniging En Onderhoud

    In het geval van de 1-kanaals VDP1000SW, zult u het startadres van het eerste toestel op 1 moeten instellen, van het tweede toestel op 2 (1 + 1), van het derde op 3 (2 + 1) enz.
  • Page 7: Prescriptions De Sécurité

    • Débranchez l’appareil s’il n’est pas utilisé ou pour le nettoyer. Tirez la fiche pour débrancher l'appareil ; non pas le câble. • Les dommages occasionnés par des modifications à l'appareil par le client, ne tombent pas sous la garantie. • Gardez votre VDP1000SW hors de la portée de personnes non qualifiées et de jeunes enfants. 3. Directives générales •...
  • Page 8 Connectez un bout du câble XLR inclus à la sortie XLR femelle à 3 broches de votre contrôleur et l’autre bout à l’entrée XLR mâle à 3 broches du VDP1000SW. Il est possible de reliez plusieurs VDP1000SWs à partir d’une connexion sérielle.
  • Page 9: Nettoyage Et Entretien

    "écoutera" son propre canal. Par conséquent, un ajustement des réglages d’un canal n’influence que l'appareil sur ce canal. Pour le VDP1000SW à 1 canal, l’adresse de départ du premier appareil est 1, du deuxième 2 (1 + 2), du troisième 3 (2 + 1) etc.
  • Page 10: Instrucciones De Seguridad

    3. Normas generales • Este aparato es un efecto de luz para uso profesional en una discoteca, un teatro, etc. La VDP1000SW sólo está permitida para una conexión con una fuente de corriente CA de máx. 230VCA / 50Hz y para el uso en interiores.
  • Page 11: Instalación

    Conexiones DMX512 Conecte la salida XLR hembra, 3 polos del controlador a la entrada XLR macho, 3 polos de la VDP1000SW con el cable XLR (incluido). Es posible conectar varias VDP1000SW en serie. Use un cable de conexión blindado de 2 conductores con conectores XLR de entrada y de salida.
  • Page 12: Limpieza Y Mantenimiento

    En el caso de de la VDP1000SW de 1 canal, la dirección inicial del primer aparato es 1. Introduzca 2 (1 + 2) para el segundo aparato, 3 (2 + 1) para el tercer aparato, etc.
  • Page 13: Einführung & Eigenschaften

    Falls Zweifel bestehen, wenden Sie sich für Entsorgungsrichtlinien an Ihre örtliche Behörde. Danke für den Kauf der VDP1000SW! Bitte lesen Sie diese Bedienungsanleitung vor Inbetriebnahme sorgfältig durch. Überprüfen Sie, ob Transportschäden vorliegen. Sollte dies der Fall sein, verwenden Sie das Gerät nicht und wenden Sie sich an Ihren Händler.
  • Page 14: Betrieb

    Verbinden Sie ein XLR-Kabel mit dem 3-Pin XLR-Ausgang der Steuerung und die andere Seite mit dem 3-Pin XLR- Eingang der VDP1000SW. Sie können verschiedene VDP1000SW in Serie schalten. Verwenden Sie ein abgeschirmtes Kabel mit XLR Ein- und Ausgangsanschlüssen. Siehe die Abbildung unten.
  • Page 15: Wartung Und Pflege

    Gerät auf einem anderen Kanal Signale empfangen. Wenn Sie die Einstellungen ändern, wird nur das besagte Gerät beeinflusst. Im Falle der 1-Kanal-VDP1000SW, werden Sie die Startadresse der ersten VDP1000SW auf 1, der zweiten VDP1000SW auf 2 (1 + 1), des dritten auf 3 (1 + 1) usw. einstellen müssen.
  • Page 16: Technische Daten

    7. Technische Daten Stromversorgung max. 230VAC / 50Hz Stromverbrauch max. 1000W Ausgangsvolumen 50m³ Projektionsabstand ± 7m Tankinhalt Sicherung F8A, 250VAC (5 x 20mm) (Artikelnummer FF8N) Abmessungen 515 x 260 x 230mm Gesamtgewicht 9.8kg Alle Änderungen vorbehalten. VDP1000SW VELLEMAN...

Table of Contents