Related Manuals for ORTEC 439
Summary of Contents for ORTEC 439
- Page 1 Model 439 Digital Current Integrator Operating Manual ® Printed in U.S.A. ORTEC Part No. 733240 0908 Manual Revision K...
-
Page 2: Warranty
In the event ORTEC fails to manufacture or deliver items called for in this agreement or purchase order, ORTEC’s exclusive liability and buyer’s exclusive remedy shall be release... -
Page 3: Table Of Contents
CONTENTS WARRANTY ................ii SAFETY INSTRUCTIONS AND SYMBOLS . -
Page 4: Safety Instructions And Symbols
SAFETY INSTRUCTIONS AND SYMBOLS This manual contains up to three levels of safety instructions that must be observed in order to avoid personal injury and/or damage to equipment or other property. These are: DANGER Indicates a hazard that could result in death or serious bodily harm if the safety instruction is not observed. -
Page 5: Safety Warnings And Cleaning Instructions
SAFETY WARNINGS AND CLEANING INSTRUCTIONS DANGER Opening the cover of this instrument is likely to expose dangerous voltages. Disconnect the instrument from all voltage sources while it is being opened. WARNING Using this instrument in a manner not specified by the manufacturer may impair the protection provided by the instrument. -
Page 7: Description
This gate may be used to meter interpolation. When combined with a preset remotely control the 439 or it may be used to inhibit scaler such as the 431, this instrument forms a the digitized output with the multichannel analyzer digital charge integrator. -
Page 8: Output
Power Supply with a full complement of to the input of the 439, it may be necessary to leave modules in the Bin; however, this may not be true the cable shield ungrounded at the current source. -
Page 9: Connector Data
The gate circuit will permit normal not create a voltage of more than 10 mV on C. For operation of the 439 when the gate input is at +3 V instance, if each beam pulse contained 10 or greater. -
Page 10: Operating Instructions
4. OPERATING INSTRUCTIONS Note: The accuracy of the 439 is not affected as long 4.1. TEST-OPERATE SWITCH as the Bal and Trig adjustments are within ±4 The Test-Operate is a three-position switch which divisions of zero. controls the function of the instrument:... -
Page 11: Offset Current Adj
Note: If a voltage and a resistor are used to form a current source, the voltage source should have a 7. Adjust the Bal potentiometer to zero the Bal/Trig value greater than 5 V. The accuracy of the 439 is Meter. 1000 ppm, which is better than the temperature and/or voltage coefficients of most high-value 8. -
Page 12: Calibration Procedure
Bal/Trig Meter. positive current and the 10 Coulomb/pulse range for negative current. If a negative current is 7. Connect the digitized output of the 439 to a scaler measured on the 10 or 10 Coulomb/pulse range that has an internal time base. -
Page 13: Analog
Digital voltmeter should read 100 mV with 1.5% 22. Set the Coulomb/pulse switch to 10 tolerance. 23. Connect a 10-mA test current to the 439 input. 15. Adjust the variable current source until the digitized output rate reads 1000 Hz. -
Page 14: Suggestions For Troubleshooting
Digital voltmeter should read 100 mV with 1.5% tolerance. Notes: The analog portion of the 439 is now calibrated. 1. All voltages were measured from ground with a voltmeter having an input impedance of 10 M or 5.3. SUGGESTIONS FOR greater. - Page 15 Reset (Auxiliary) +12 V Coaxial Coaxial 1 2 V Spare bus Coaxial Reserved bus 117 V ac (neutral) Spare High-quality ground Spare Ground guide pin Reserved Pins marked (*) are installed and wired in ORTEC’s 4001A and 4001C Modular System Bins.
Need help?
Do you have a question about the 439 and is the answer not in the manual?
Questions and answers