Advertisement
Quick Links
AL101S Steering Gear Alarm System
Chapter 0 - Factory default
Chapter 1 - Operation of AL101S series ECR / FWD / AFT
Description of AL101S series keypad
Description of AL101S series lamp
Chapter 2 - Size of AL101S series ECR / FWD / AFT
Chapter 3 –Input & Output signal terminal of AL101S ECR / FWD / AFT
Chapter 4 – Test flow chart of AL101S
1
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for Sewhacnm AL101S
Summary of Contents for Sewhacnm AL101S
- Page 1 Description of AL101S series keypad Description of AL101S series lamp Chapter 2 - Size of AL101S series ECR / FWD / AFT Chapter 3 –Input & Output signal terminal of AL101S ECR / FWD / AFT Chapter 4 – Test flow chart of AL101S...
- Page 2 Chapter 0 Factory Default 1. ECR 1.1 Dip Switch Switch Default Operation Mode Test Mode No DC blinking DC blinking Available Full Relay output Mode Half relay output Mode Operation Mode Download Mode 1.2 Resistor Termination ON/OFF switch: OFF...
- Page 3 2. FWD / AFT 1.1 Dip Switch Switch Default Operation Mode Test Mode No DC blinking DC blinking Available Full Relay output Mode Half relay output Mode Operation Mode Download Mode 1.2 Resistor Termination ON/OFF switch: OFF CAUTION! ECR / FWD / AFT Relay output mode(Full / Half) run independently.
- Page 4 AL101S Steering Gear Alarm System Chapter 1 ECR / FWD / AFT Operation...
- Page 5 AL101S-ECR AL101S-FWD AL101S-AFT...
- Page 6 AL101S-FWD...
- Page 7 AL101S-AFT...
- Page 8 1) SILENCE Key This key able to maintain to each lamp’s activation or deactivation After buzzer has activation, this key able to stop to buzzer sound CAUTION! If setting Dip Switch “3” setting done ON, relay output will be working full mode. Meanwhile if setting Dip switch “3”...
-
Page 9: Lamp Test Key
3) LAMP TEST Key This key able to all LAMP ON even each lamp has activation or deactivation This key check to LAMP itself working. If on pressing this key both of activation and deactivation lamp ON at once. Then if release this key the deactivation lamp will be OFF 4) DIMMER Key This key able to adjust to LAMP brightness Brightness has total 5 steps. - Page 10 Description of AL101S-ECR/FWD/AFT LAMP 1) FU FAIL LAMP Input signal “1” second later LAMP activate 2) PUMP HYDR. LOCK LAMP Input signal “1” second later LAMP activate 3) PHASE FAIL LAMP Input signal “2” second later LAMP activate 4) PUMP LOW OIL LEVEL LAMP Input signal “3”...
- Page 11 AL101S Steering Gear Alarm System Chapter 2 ECR / FWD / AFT Case size...
- Page 12 Cut hole dimension...
- Page 13 Fontal case dimension...
- Page 14 AL101S Steering Gear Alarm System Chapter 3 ECR / FWD / AFT Input & output signal terminal...
- Page 15 ECR input & output signal terminal...
- Page 16 FWD input & output signal terminal...
- Page 17 AFT input & output signal terminal...
- Page 18 AL101S Steering Gear Alarm System Chapter 4 Test flow...
- Page 19 4.1 Purpose : This alarm testing procedure is to check and confirm that the alarm system is working and meet the design requirement. 4.2 Testing Procedure 4.2.1 Connect the FWD, AFT & ECR panel as single line drawing. 4.2.2 Connect ECR panel to external alarm signals. The alarm signal can be turned off And on by a toggle switch.
- Page 20 PUMP 1 RUN Step 1: Close PUMP 1 RUN switch Step 2: PUMP 1 RUN indicator light ON Step 3: Buzzer not on. Step 4: Open the PUMP 1 RUN switch Step 5: Indicator light off PUMP 1 STOP Step 1: Close PUMP 1 STOP switch Step 2: PUMP 1 STOP indicator light on Step 3: Buzzer not on.
- Page 21 4.6 Testing for signal output to other equipment FWD & AFT alarm panel relay Signal output...
Need help?
Do you have a question about the AL101S and is the answer not in the manual?
Questions and answers