Download
Share
Print this page
  1. Manuals
  2. Brands
  3. Sewhacnm Manuals
  4. Security System
  5. AL-101
  6. Manual

Sewhacnm AL-101 Manual

Steering gear alarm system
Hide thumbs

Advertisement

Quick Links

Download this manual
Steering Gear Alarm System
AL-101
Maunual
1

Advertisement

loading
Need help?

Need help?

Do you have a question about the AL-101 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Sewhacnm AL-101

Summary of Contents for Sewhacnm AL-101

  • Page 1 Steering Gear Alarm System AL-101 Maunual...
  • Page 2 AL101 Steering Gear Alarm System Chapter 0 – Dip Switch factory default Chapter 1 - Operation ECR / FWD / AFT / VDR Description keypad Description lamp Chapter 2 - Dimension of AL101 series ECR / FWD / AFT / VDR Chapter 3 –Input &...

  • Page 3: Factory Default

    Chapter 0 Factory Default 1. ECR / FWD / AFT 1.1 Dip Switch Switch Default Operation Mode Test Mode DC ON lamp blink DC ON lamp ON (Red / Green) (Red) Full Relay Half relay output Mode output Mode Firmware download Normal mode 1.2 Resistor Termination ON/OFF switch: OFF 2.
  • Page 4 AL101 Steering Gear Alarm System Chapter 1 ECR / FWD / AFT / VDR Operation...
  • Page 5 AL101 Steering Gear Alarm System ECR / FWD / AFT / VDR General Specification - Voltage: DC 24V - Current: 1.6A(38A) - Communication: CAN BUS / RS485 / NMEA018(RS422) Features - Compact size, with easy access to wiring on rear connector. - 4 wires CAN BUS data transmission - Software utilizing 20 years experiences in control system - Big square dial keypad for easy access to function button...
  • Page 6 System Configuration CAUTION! ECR to FWD are the main line RxTx unit, meaning wiring MUST be firstly from ECR to FWD then to either AFT to VDR or vice versa or anyone. If FWD to AFT data line is broken then ECR to FWD will still be operational.
  • Page 7 Frontal Face AL101-ECR...
  • Page 8 AL101-FWD...
  • Page 9 AL101-AFT...
  • Page 10 AL101-VDR...
  • Page 11 Description of AL101-ECR/FWD/AFT/VDR Keypad 1) SILENCE Key This key able to maintain to each lamp’s activation or deactivation After buzzer has activation, this key able to stop to buzzer sound CAUTION! If setting Dip Switch “2” setting done ON, relay output will be working full mode. Meanwhile if setting Dip switch “2”...

  • Page 12: Lamp Test Key

    3) LAMP TEST Key This key able to all LAMP ON even each lamp has activation or deactivation This key check to LAMP itself working. If on pressing this key both of activation and deactivation lamp ON at once. Then if release this key the deactivation lamp will be OFF 4) DIMMER Key This key able to adjust to LAMP brightness Brightness has total 5 steps.
  • Page 13 Description of AL101-ECR/FWD/AFT LAMP 1) FU FAIL LAMP Input signal “1” second later LAMP activate 2) PUMP HYDR. LOCK LAMP Input signal “1” second later LAMP activate 3) PHASE FAIL LAMP Input signal “2” second later LAMP activate 4) PUMP LOW OIL LEVEL LAMP Input signal “3”...
  • Page 14 AL101 Steering Gear Alarm System Chapter 2 ECR / FWD / AFT Dimension...
  • Page 15 ECR / FWD / AFT...
  • Page 17 AL101 Steering Gear Alarm System Chapter 3 ECR / FWD / AFT / VDR Input & output signal terminal...
  • Page 18 ECR input & output signal terminal...
  • Page 19 FWD input & output signal terminal...
  • Page 20 AFT input & output signal terminal...
  • Page 21 VDR output signal terminal...
  • Page 22 AL101 Steering Gear Alarm System Chapter 4 Test flow...
  • Page 23 4.1 Purpose : This alarm testing procedure is to check and confirm that the alarm system is working and meet the design requirement. 4.2 Testing Procedure 4.2.1 Connect the FWD, AFT & ECR panel as single line drawing. 4.2.2 Connect ECR panel to external alarm signals. The alarm signal can be turned off And on by a toggle switch.
  • Page 24 Step 1: Close PUMP 1 RUN switch Step 2: PUMP 1 RUN indicator light ON Step 3: Buzzer not on. Step 4: Open the PUMP 1 RUN switch Step 5: Indicator light off PUMP 1 STOP Step 1: Close PUMP 1 STOP switch Step 2: PUMP 1 STOP indicator light on Step 3: Buzzer not on.
  • Page 25 FWD & AFT alarm panel relay Signal output ECR 알람 패널 릴레이 신호 출력 4.7 Testing for signals output to VDR Every indicator light will have a respect +24V DC output at VDR option or data output for NMEA protocol option.
  • Page 26 1. The Warrantee period, we can guarantee, is one(1) year from your purchasing date 2. Warrantee Exception Clause - Warrantee period is expired. - Any kinds of Mal-function or defection caused by Modification or Repair without Sewhacnm’s permission. - Any kinds of Mal-function, Defection, or External damage, caused by operator - Any kinds of Mal-function, Defection, caused by using spare part from Non-Authorized Distributor or Agent.