Table of Contents
Advertisement
en Steaming
10.
Empty the water tank and dry the cooking compart-
ment.
→ "After using steam operation", Page 18
Changing the type of steam heating
When you change the type of steam heating, the other
settings are also reset.
1.
Press
.
2.
Press
.
3.
Press the required type of steam heating.
4.
Reset the operation and use
Changing the temperature
Once the operation has started, you can change the
temperature at any time.
1.
Press the temperature.
2.
Change the temperature using
justment bar. Or enter the temperature directly via
the number field
.
3.
Press "Apply".
Changing the cooking time
You can change the cooking time at any time.
1.
Press the cooking time.
2.
Change the cooking time using
adjustment bar. Or enter the temperature directly via
the number field
.
3.
Press "Apply".
11.4 Setting added steam
Requirements
¡ Observe the information about the respective operat-
ing mode.
→ "Setting options with steam", Page 17
¡ The water tank has been filled. If the water tank runs
dry during operation, a message appears on the dis-
play. The appliance continues to operate but without
injecting steam into the cooking compartment.
→ "Filling the water tank", Page 16
1.
Press the operating mode that you require.
2.
Select the settings for the operating mode, e.g. type
of heating and temperature.
3.
Press "Added Steam" .
4.
Press the required steam level.
Steam level
1
2
3
5.
Press "Apply".
6.
Press
to start the operation.
a The appliance starts heating.
a The setting values and how long the appliance has
already been in operation are shown on the display.
7.
When the food is ready, use
ance off.
8.
Empty the water tank and dry the cooking compart-
ment.
→ "After using steam operation", Page 18
Changing added steam
You can change or deactivate the added steam func-
tion at any time.
1.
Press the steam level.
18
to start.
or
or via the ad-
or
, or via the
Added steam
Low
Medium
High
to switch the appli-
2.
Change or deactivate added steam.
3.
Press "Apply".
11.5 Setting the steam jet function
Requirements
¡ Observe the information about the respective operat-
ing mode.
→ "Setting options with steam", Page 17
¡ The water tank has been filled. If the water tank runs
dry during operation, a message appears on the dis-
play. Operation is stopped.
→ "Filling the water tank", Page 16
1.
Press the operating mode that you require.
2.
Select the settings for the operating mode, e.g. type
of heating and temperature.
3.
Start the operation.
4.
Press "Steam jet"
a The appliance starts to heat the water.
5.
When the water is heated up, press "Steam jet"
again.
a The steam jet is triggered and the appliance adds
clouds of steam to the cooking compartment for ap-
prox. 3 to 5 minutes.
a When the steam jet has finished, the operation con-
tinues to run as normal. Depending on the opera-
tion, the steam jet can be triggered again if neces-
sary.
6.
When the food is ready, use
ance off.
7.
Empty the water tank and dry the cooking compart-
ment.
→ "After using steam operation", Page 18
Cancelling the steam jet
You can cancel the steam jet at any time.
▶
Press "Steam jet" .
a "Steam jet"
"Off" appears in the display.
a The operation continues without the steam jet.
11.6 After using steam operation
Dry the appliance after each steam operation.
Note: Traces of limescale may remain in the cooking
compartment after operation with steam. The functional-
ity of the appliance is not affected by this. You can re-
move traces of limescale using hot water or a cloth
soaked in vinegar. Observe the information on clean-
ing.
→ "Cleaning and servicing", Page 24
Emptying the water tank
WARNING ‒ Risk of burns!
The water tank may heat up while the appliance is in
operation.
▶
Wait until the water tank has cooled down from the
previous operation.
▶
Remove the water tank from the tank recess.
ATTENTION!
Drying the water tank in the hot cooking compartment
leads to damage to the water tank.
▶
Do not dry the water tank in the hot cooking com-
partment.
at the desired time.
to switch the appli-
Advertisement
Table of Contents
