Electrostatic Oil Mist Collector CE Series Contents Page 1. General instructions……………………………2 Electrostatic oil mist collector operation theory and method 1.2 Transportation instructions………………… 3 1.3 Disposal instructions……………………… 2. CE series technical data…………………… 4 3. CE series spare parts……………………… 4. Circuit diagram………………………………… 9 5.
Electrostatic oil mist collector operation theory and method TCSM electrostatic oil mist collector is applied for lathe and milling machine filtration and reuse of coolant. This model uses several parts. (As shown in Figure 1) 1. The dispersion zone: The conflict plate forces the oil drop disperse into smaller oil mist.
Electrostatic Oil Mist Collector CE Series Transportation instructions 1.2.1 Packing: 1.2.2 Transportation CE series are packed with Wooden Box Depending on <Table 1> Collector weight, use appropriate vehicle to move Collector(like Stacker), Person who using the vehicle must have relevant knowledge and qualification to carry it 1.3 Disposal instructions...
Electrostatic Oil Mist Collector CE Series 2. CE series technical data Type Unit CE-900 CE-1000 CE-1800 CE-2200 Air flow 1000 1800 2200 volume Power 0.45 0.45 0.875 1.275 dB(A) Noise Motor frequency Motor rotating r/min 2500 2860 1430 2860 speed...
(plastic/steel) to reduce oil drop intake volume. 5.1.4. Connection between air duct and CE series collectors should not leak, and air duct layout should prevent oil accumulation inside air duct. Also, could install “Front oil blocker” or PVC pipe to...
Electrostatic Oil Mist Collector CE Series 5.1.5. After the power distribution is completed, it is necessary to confirm that all power terminal contacts in the machine are tightened well and confirm that the rotation of the wind wheel and motor are correct according to the sticker deration.
Electrostatic Oil Mist Collector CE Series 5.2.2 Before starting up 5.2.2.1 Please double check the power distributions are tightened well. 5.2.2.2 Motor rotation direction: The direction of rotation of the motor must be checked as follows: - Use the hand switch to turn on the machine.
The following power off, please wait 10 minutes before performing maintenance.) table shows the monthly maintenance schedule. For cleaning method, please refer to 6.3.1 Manual cleaning CE series Oil Mist Collector- monthly maintenance schedule Item Check Parts Checked Situation Maintenance If filter can’t clean up by...
Electrostatic Oil Mist Collector CE Series 6.2 Troubleshooting Before maintenance, the main power supply should be powered off and a padlock should be added. After power off, please wait 10 minutes before performing maintenance. Disturbance Possible causes Way to resolve the problem Indicator 6.2.1Motor and...
Electrostatic Oil Mist Collector CE Series 6.3 Electrode plate cleaning 6.3.1 Manual cleaning Item Icon Instruction Please choose a neutral detergent with good degreasing performance and follow the formula of the lotion. If you use (strongly acidic) aluminum lotion, Water...
Electrostatic Oil Mist Collector CE Series Use the pressurized air to remove the water in parallel direction. If user cannot confirm whether water has been totally removed, please let Electrode plate sit for a period of time to remove remaining water.
Electrostatic Oil Mist Collector CE Series Fully immerse the electrode plate in the prepared cleaning tank (hot water 50~60 ℃, the best value can be adjusted and tested by user). Turn on the ultrasonic device and Ultrasonic cleaning adjust the cleaning time according to the actual situation.
Electrostatic Oil Mist Collector CE Series Warranty If you have any questions, please contact us with the information below. CHEN SHIN (TCSM) MC CO., LTD TEL:+886-4-7331657 FAX:+886-4-7330116 chenshin.h@gmail.com EMAIL: assa.tcsm@gmail.com ; Office Add.: No. 66, Aly. 208, Bianxing Ln., Xuetian Rd., Wuri Dist.,Taichung City 414011 , Taiwan ,R.O.C.