Advertisement
Operating Instructions and Parts Manual
CAUTION: DO NOT overload the sliding worktop. Sliding top is
equipped with slides rated to 100 Lbs. While the total capacity of the
worktop can withstand up to 800 Lbs., if the sliding top opens, the
slides will fail which may lead to property damage and/or personal
injury. Ensure the top is locked in the closed position prior to placing
any heavy object onto the worktop.
CAUTION: DO NOT attempt to balance items/tools on the
connection point of the box. The force may cause the slide top to separate
unexpectedly, leading to personal injury and/or property damage.
ASSEMBLY INSTRUCTIONS
CAUTION Contents are heavy; assistance is recommended with
this assembly process.
CHESTS
1. Remove all contents from packaging and locate the assembly
hardware.
NOTE : All fasteners are the same size.
Chests that have no front locking panel are equipped with a locking mechanism actuated by the lid. When the lid is
closed, tabs in the lock bar engage the pockets on the drawer. When lid is open, tabs are raised clear of pockets.
2. If unlocked, open the sliding top and flip the internal lever to the
lock position to lock the drawers closed. Use the key to lock the top
compartment closed.
3. Set the Cart Top onto a protected surface. A short side should be
facing up; the uprights and handle must be assembled in the same
process.
4. Place the first upright on one edge of the cart. The holes on the
uprights will only fit in one orientation. If the holes do not line up,
flip the upright 180° and re-assess.
5. Tighten the front fasteners until finger tight, allowing the upright to
shift.
6. Repeat steps 4 and 5 for the second upright. Then use a ratchet or
wrench to tighten the hardware completely.
7. With assistance, flip the cart to the opposite short side and follow
steps 4-6. Align the holes on the short side of the cart, and tighten
all hardware until finger tight.
8. Install the casters onto the bottom tray. The locking casters must
be installed on the same side of the tray and should be installed on
the same side as the handle.
9. Fit the tray between the bottom of the 4 uprights and use hardware
to fasten into place. It is recommended that all hardware be
TROLLEYS
tightened to finger tightness before tightening completely.
10. With assistance, lift the cart into an upright position. Lock the
locking casters.
11. Fit the tray dividers as needed in the provided slots. The flat portion
of the divider should be facing down into the tray. DO NOT attempt
to force the divider into place. If the divider is upside down, the
rolled edge will not allow placement.
REMOVING THE DRAWERS
1. Fully extend the empty drawer.
2. While pushing the release lever up on the left side of the drawer,
pull down the release lever on the right side of the drawer.
8/19
2019 OEMTOOLS
®
36" 3-DRAWER SLIDE TOP CART
Drawers must be fully closed before lid is shut. DO NOT slam the drawers when lid is shut as they will not
lock and slight damage to lock bar tabs or lock pockets may occur.
Should this happen, remove drawer and with a screwdriver straighten out the deformed tab; for lock
Pockets, a pairs should be used.
(Figure 1)
Lever
Left Hand Side
of Slide, Pushing
Lever Up
REINSTALLING THE DRAWERS
1. Fully extend the empty drawer slides.
2. Insert the brackets on each side of the drawer into the slots on the
slides, being careful that they are properly positioned.
3. Once inserted, close the drawer completely to set the slides properly.
NOTE: DO NOT force the drawers into place; if the drawer gets
stuck, remove and reinstall.
MAINTENANCE
1.
Periodically tighten all hardware.
2.
Lubricate the drawer slides twice a year.
3.
Lubricate the lock with graphite each year.
4.
Use a damp microfiber cloth to clean all surfaces.
ATTENTION:
Lock pocket
DRAWER LOCKING MECHANISM
1.
During the installing the drawer, it is regular that you will fell tight when you pu
CAUTION: OEMTOOLS
will not cover damage to locking tabs,
®
2.
Please push the drawer into the end and pull out for 2-3 times to check wheth
nor provide replacement drawers. If safety instructions and the locking
moved smoothly or not.
instructions below are followed, the locking mechanism will remain fully
a.
if the drawer moves un-smoothly or tight, even jams up, it means you are
functional. OEMTOOLS
is not responsible for damage caused by user
®
drawer, pls. take out drawer and install again.
negligence or failure to read and understand the instructions provided in
b.
if the drawer moves smoothly, it means you are successful to install the d
this manual. A drawer will never be difficult to close unless there is an
obstruction. If the drawer will not close easily, re-open the drawer and
check for obstruction or damaged/worn slides; NEVER slam the drawer
shut.
LUBRICATION
TROLLEYS
CAUTION: DO NOT slam the drawer closed if the tubular lock has
It is important for the smooth operation of the sliders to lubricate them periodically
Locking mechanism used on trolleys is engaged by rotaing cam lock with a key.
been engaged. This may cause damage to the internal locking mechanism.
This should be done at least twice a year or more frequently depending on usage.
Drawers should be fully closed before locking mechanism is engaged.
NOTE: It is recommended that you unlock the tubular lock before
Drawers that are not fully closed after locking mechanism has been
attempting to close any open drawers; however, if you press the
engaged, just close it and will be locked auto.
drawer in, the drawer will lock. (Figure 2)
NOTE: If the drawer was slammed while the locking mechanism was
engaged, and damage to the mechanism is suspected, follow instructions
SIDE HANDLE
provided in this manual to remove the drawer. Inspect the locking tab for
damage. Use a screwdriver and/or pliers to straighten the tab.
a. Fixed the side handle with screw
b. Must be fixed on the same side as swivel caster.
3
24730, 24731, 24732
Retaining Clip
Figure 1
Right Hand Side,
Pushing Lever down
Lock bar tab
Figure 2
HOW TO R
Drawer sliders
remove drawe
be released by
Sliders) and d
simultaneousl
HOW TO R
Pull the slide o
Advertisement
