Quoizel BRY8406PN Assembly Instruction Sheet

Quoizel, Inc.
6 Corporate Parkway
Goose Creek, SC 29445
Customer Service
Phone 631.273.2700
Fax 631.231.7102
www.quoizel.com
Warnings and Cautions
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly
recommend that a licensed, professional electrician perform the installation.
Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal. Do not subject
glass parts to any shock while in operation or shattering may result.
Package Contents
-
STEP 1 Install Crossbar
A. Pass the supply wires through the Crossbar Assembly (AA). Attach
the Crossbar Assembly (AA) to the Outlet Box with the head of the
Green Ground Screw facing you. Secure it with Outlet Box Screws
(not included). Tighten until snug.
Outlet Box
Figure 1
-
STEP 2 Fit Fixture Body to Crossbar
Assembly
A. Remove mounting balls from the
Crossbar Assembly (AA). Fit the
Fixture Body (A) Crossbar Assembly
(AA) and secure with mounting balls.
Note: The backplate of the Fixture
Body (A) should be snug against the
wall surface and the mounting balls. If
not, adjust the length of the nipple on
the Crossbar Assembly (AA) by
unscrewing the preassembled hex nut
and lock washer and then screwing
the mounting screws in or out of the
crossbar until the correct length is
achieved. Once the backplate of the
Fixture Body (A) is secure, remove the
mounting ball and Fixture Body (A)
and proceed to Step 3.
Need assistance with parts or assembly? Call Quoizel customer service at 1-631-273-2700
2014 QuoizelInc.
Assembly Instruction Sheet #IS-BRY8406PN
Tools Required: Flathead screwdriver, Phillips screwdriver, pliers, wire cutters, wire strippers, electrical tape,
safety glasses.
Bulb Recommended: (1) Medium Base 100W Maximum, Alternate bulb (1) 23W CFL
Estimated Assembly Time: 30-45 minutes
Preparation: Identify and inspect all parts before beginning installation. Check package content list and diagrams
below to be sure all parts are present. If any parts are missing or damaged, do not attempt to assemble, install, or
operate the fixture. Contact customer service for replacement parts.
Fixture can only be mounted in the direction indicated on page 2.
Fixture
A Body
x 1
Supply Wires with
Ground Wire
AA
Outlet Box Screws
(not included)
Mounting
Ball
Hex Nut and
Lock Washer
Mounting
Screw
A
Thank you for purchasing a Quoizel product.
or visit us on-line at www.quoizel.com
For Style BRY8406PN
Hardware Contents
STEP3 - Wire Connections
A. Use standard wire connectors (not included) to make all wire
connections. (Connectors are not included with fixture.) Strip and
prepare wire ends according to instructions supplied with
connectors.
B. Connect White Supply Wire from the Outlet Box to Ribbed side Wire
from fixture.
C. Connect Black (or Red) Supply Wire from the Outlet Box to Smooth
side Wire from fixture.
D. Connect Ground Wire from the Outlet Box to Ground Wire from
fixture.
E. Twist connectors until wires are tightly joined together.
F. Wrap each connection with approved electrical tape and carefully
stuff all the connected wires into the Outlet Box.
White wire
from supply
Black wire from
supply (or Red)
Ground wire
from supply
-
STEP 4 Install Fixture Body
A. Carefully tuck all wires into the outlet
box and position the backplate of
fixture body (A) over the outlet box.
Align the holes in the backplate with
the mounting screws. Place caulk (not
AA
supplied) into the previously removed
mounting balls and then attach fixture
body (A) using the mounting balls.
Hand tighten until snug.
Figure 2
1of2
Crossbar Assembly
AA
x 1
Ribbed side wire
from fixture
Smooth side wire
from fixture
Ground wire
from fixture
Figure 3
Mounting
Ball
Hex Nut and
Lock Washer
A
Mounting
Screw
Figure 4
AA
March2014