Konica Minolta Magicolor 2300 DL Supplementary Manual
Konica Minolta Magicolor 2300 DL Supplementary Manual

Konica Minolta Magicolor 2300 DL Supplementary Manual

Magicolor 2300 series
Hide thumbs Also See for Magicolor 2300 DL:

Advertisement

®
magicolor 2300
Series
Repacking Guide
1760504-001A

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Magicolor 2300 DL and is the answer not in the manual?

Questions and answers

Summary of Contents for Konica Minolta Magicolor 2300 DL

  • Page 1 ® magicolor 2300 Series Repacking Guide 1760504-001A...
  • Page 2 Center Building, 1-6-1 Marunouchi, Chiyo da-ku, To kyo, 100-0005, Japa n. All Rights Reserve d. This do cume nt may not be co pied, in whole or part, nor transferred to a ny other media o r language, without written pe rmission of KONICA MINOLTA BUSINESS TECHNOLOGIES, INC.
  • Page 3: Storing The Printer

    Attention Failure to follow these instructions could result in voiding your warranty. Storing the Printer Unplug the printer when storing it for an extended period. Protect it from extremes in temperature and humidity, and from dust. Relocating Your Printer Occasionally, you may have to move your printer to a different location, either nearby or to a distant location.
  • Page 4: Repacking The Printer

    For locations outside the Americas, refer to printer.konicaminolta.com. If you have been instructed to return the printer to KONICA MINOLTA PRINTING SOLUTIONS U.S.A., INC. by a customer support representative in the Americas, be sure to write the RMA (Return Merchandise Authorization) number you received on the outside of both the printer and consumables cartons before shipping them.
  • Page 5: Turn Off The Printer, Unplug The Power Cord, And Remove The Interface Cables

    Repacking your printer for shipment involves the following steps. Each is described in more detail in the following sections. Obtain Proper Packaging: Original packaging or replacement packaging magicolor 2300 DL Replacement Packaging Kit 2600723-100 magicolor 2350 Replacement Packaging Kit 2600723-200, or magicolor 2300W Replacement Packaging Kit 2600723-300 Repacking kit...
  • Page 6: Remove The Media And The Tray 1 Media Support

    B. Remove the Media and the Tray 1 Media Support Remove the media. Place it in its original packaging and store in a cool, dark place on a level surface. Avoid moisture, excess humidity, direct sunlight, excess heat (above 95° F/35° C), and dust. Lift the media support from the three holes in Tray 1 and remove the media support.
  • Page 7 Unhook the support wire. Close the right-side door. Open the duplex option’s cover and loosen the two thumbscrews until the duplex option moves freely away from the right side of the printer. Lift duplex option up and away from the printer. Install the original right-side cover that came with the printer with two screws.
  • Page 8: Lower Feeder Unit

    Lower Feeder Unit If you don’t have a lower feeder unit installed, skip to the next section. Slide tray 2 out of the printer and remove the media. Remove the brackets (two at the front and one at the back) used to attach the lower feeder unit to the printer.
  • Page 9: Remove The Waste Toner Bottle, Plug The Openings, And Dispose Of It According To Your Local Regulations

    D. Remove the Waste Toner Bottle, Plug the Openings, and Dispose of It According to Your Local Regulations Open the printer’s front door, grasp the waste toner bottle’s handle, and pull the waste toner bottle outward and upward. Carefully remove the waste toner bottle. Keep the waste toner bottle upright while the openings are not covered, so the toner does not spill.
  • Page 10: Remove The Transfer Belt

    Grasp the release lever on the OPC drum cartridge, and then pull the cartridge straight out about 6 inches (152 mm). Attention The OPC drum is extremely sensitive to bright light and direct sunlight. Any exposure to light should be avoided, or permanent damage could result.
  • Page 11 Grasp the transfer belt and pull it straight out and then lift it up. Place the transfer belt and thumbscrews in the protective bag supplied in the repacking kit (magicolor 2300 Series Repacking Kit 2600733-100). Replace the packaging and tape, then close the front door. G.
  • Page 12 Position the cardboard label next to the printer. Open the two green levers at the top of the fuser unit. Insert the fuser separators holes underneath the levers. Close the two green levers Tape the cardboard label the top of the printer. Close the right-side door into the Repacking the Printer...
  • Page 13: Repack The Printer For Shipment

    H. Repack the Printer for Shipment Use your own original packaging or order the appropriate Replacement Packaging Kit. (Refer to the chart on page 2.) Replace the tape and packaging. Repacking the Printer...
  • Page 14 Place the lower cushions into the shipping carton. Place the printer’s plastic bag over the printer. Pack the printer for shipment as shown. If you’re also shipping the power cord and any manuals with the printer, place them in the shipping carton.
  • Page 15: Reinstalling The Printer

    I. Repack the OPC Drum Cartridge and Transfer Belt Unit for Shipment Order the magicolor 2300 Series Repacking Kit 2600733-100. Place the OPC drum cartridge and transfer belt unit (in their protective bags) in the appropriate position in the box supplied in the repacking kit.
  • Page 16 A. Unpack the Printer Carton Refer to the magicolor 2300 DL, magicolor 2350, or magicolor 2300W Installation and User’s Guides. B. Remove the Fuser Separators Pull the right-side door release then open the right-side door Open the two green levers the top of the fuser unit.
  • Page 17 Remove the separators and the attached label Close the two green levers Close the right-side door. C. Reinstall the Transfer Belt Unit With the front door open, remove the transfer belt unit from its protective bag and reinsert it. Tighten the two thumbscrews. Reinstalling the Printer...
  • Page 18 (7 o’clock) position. Close the front door. Steps D. through J. Refer to the magicolor 2300 DL, magicolor 2350, or magicolor 2300W Installation and User’s Guides. The printer must complete a 150-second calibration cycle after a consumable has been replaced.

This manual is also suitable for:

Magicolor 2300Magicolor 2300wMagicolor 2350

Table of Contents