Bosch Professional GCM 18V-305 GDC Original Instructions Manual page 44

44 | English
Connectivity functions
In conjunction with the GCY 42 Bluetooth® Low Energy Mod-
ule, the following connectivity functions are available for the
power tool:
– Registration and personalisation
– Status check, output of warning messages
– General information and settings
– Management
– Setting the speed levels
Read the corresponding operating instructions for informa-
tion about the Bluetooth® Low Energy Module GCY 42.
The smartphone indicator (49) lights up when the power
tool sends information (e. g. temperature warning) to a mo-
bile device via Bluetooth® wireless technology.
Practical advice
General sawing instructions
Always tighten the locking knob (12) and the clamp-
u
ing handle (14) firmly before sawing. Otherwise the
saw blade can become wedged in the workpiece.
For all cuts, it must first be ensured that the saw blade
u
at no time can come in contact with the fence, screw
clamps or other machine parts. Remove any mounted
auxiliary stops or adjust them accordingly.
With the Bluetooth® Low Energy Module GCY 42, the
u
power tool is equipped with a radio interface. Local
operating restrictions, e.g. in aircraft or hospitals,
must be observed.
In areas where the Bluetooth® wireless technology is
u
not allowed to be used, the Bluetooth® Low Energy
Module GCY 42 and the button cell must be removed.
Protect the saw blade against impact and shock. Do not sub-
ject the saw blade to lateral pressure.
Do not saw warped/bent workpieces. The workpiece must
always have a straight edge to face against the fence.
The free end of long and heavy workpieces must have some-
thing placed underneath it or be supported.
Make sure that the retracting blade guard operates properly
and that it can move freely. The retracting blade guard must
open when the tool arm is guided downwards. When the tool
arm is guided upwards, the retracting blade guard must
close again over the saw blade and lock in the uppermost po-
sition of the tool arm.
Only saw materials which are permitted within the scope of
the intended use.
Marking the cutting line (see figure M)
A laser beam shows you the cutting line of the saw blade.
This allows for exact positioning of the workpiece for sawing,
without having to open the retracting blade guard.
– To do this, switch on the laser beam by briefly pressing
the on/off switch (64) without pressing the lock-off but-
ton (2).
– Align your mark on the workpiece with the right-hand
edge of the laser line.
1 609 92A 5HG | (08.04.2020)
Note: Before sawing, check if the cutting line is still indic-
ated correctly (see "Adjusting the laser", page 45). The
laser beam can be misplaced due to vibrations from intens-
ive use, for example.
Position of the operator (see figure N)
Do not stand in line with the saw blade in front of the
u
power tool. Always stand to the side of the saw blade.
This protects your body against possible kickback.
– Keep hands, fingers and arms away from the rotating saw
blade.
– Do not reach one hand across the other when in front of
the tool arm.
Replacing insert plates (see figure O)
The insert plates (10) can become worn after prolonged use
of the power tool.
Replace faulty insert plates.
– Bring the power tool into the work position.
– Loosen the screws (65) using the hex key (18) and re-
move the old insert plates.
– Insert the new right-hand insert plate.
– Screw the insert plate as far as possible to the right with
the screws (65) so that the saw blade does not come into
contact with the insert plate over the entire length of the
possible slide motion.
– Repeat the work steps in the same manner for the new
left-hand insert plate.
Permissible workpiece dimensions
Mitre angle Bevel angle
0° 0°
45° (left) 0°
0° 45° (left)
0° 45° (right)
45° 45° (left)
45° 45° (right)
A) With horizontal spacer (height x width: 60 mm x 400 mm)
B) With vertical spacer (height x width: 72 mm x 50 mm)
Minimum workpiece dimensions (= all workpieces that can
be secured left or right of the saw blade using the supplied
screw clamp (19)): 160 mm x 35 mm (length x width)
Maximum cutting depth (0°/0°): 120 mm
Sawing
Always tighten the locking knob (12) and the clamp-
u
ing handle (14) firmly before sawing. Otherwise the
saw blade can become wedged in the workpiece.
Height x width
[mm]
104 x 341
A)
45 x 400
B)
120 x 250
180 x 40
104 x 240
180 x 20
60 x 341
40 x 341
60 x 240
40 x 240
Bosch Power Tools