LG 26LH1DC1-UB Service Manual page 17

3. Commercial Interface Installer's Menu Setting
3.1 Accessing the Installer's Menu
Make sure TV is on. Installer's menu items can be accessed by using an installer's remote control.
Just press MENU repeatedly(at least 10 times) until the TV seems to stop responding, then press 9, 8, 7, 6, then ENTER.
To exit the Installer's Menu, press ENTER again. Any changes you make will be stored in nonvolatile memory.(The menu also disappears automatically.)
The Installer's menu opens with item 000 INSTALLER SEQ 000. Use the Up/Down arrow keys to sequence through the available menu items.
Or, access an item directly by keying in the line number, then pressing MENU. For example, to access the Sleep Timer option which is item 015,
press 0-1-5, then MENU. To change a setting, use the Left/Right arrow keys. Or, enter a value directly. Press ENTER to remove Installer menu display.
Typical Installer Menu
26LH1DC1-UB INSTALLER MENU
000 INSTALLER SEQ 000
UPN : 000-000-000-000 FPGA 09F1
PTC V1.00.000
3.2 Using the Installer's Menu
Items 000 ~ 117 are immediately accessible only upon entering the Installer's Menu.
Their numbers, descriptions, ranges, factory default settings, and a place for listing any changes made on-site are given below and on the following pages.
Installer Menu Items 000 through 117
Menu
Function
Item
000 INSTALLER SEQ
001 POWER MANAGE
002 AC ON
003 BAND/AFC
004 STRT CHANNEL
005 CHAN LOCK
007 STRT VOLUME
008 MIN VOLUME
009 MAX VOLUME
010 MUTE DISABLE
011 KEY DEFEAT
015 SLEEP TIMER
016 EN TIMER
017 ALARM
021 V-CHIP
022 MAX BLK HRS
023 CAPTION LOCK
028 CH. OVERIDE
029 OLD OCV
030 ACK MASK
031 POLL RATE
032 TIMING PULSE
034 CAMPORT EN
035 CAMPPORT EN
038 YPrPb EN
039 REAR AUX EN
040 AUTO CAMPORT
046 STRT AUX SRCE
047 AUX STATUS
053 DIS. CH-TIME M.
069 EN. CH-T COL.
070 FOR. CH-TIME
071 BCK. CH-TIME
073 CH NOT AVBLE
075 REVERT CH
078 UPN MSB
079 UPN MSB-1
080 UPN MSB-2
081 UPN LSB
Copyright©2007 LG Electronics. Inc. All right reserved.
Only for training and service purposes
CPU V1.25.00
Value Default
Range Value
000~3 000
000~7 000
000~1 000
000~3 001
000~127, 255 255
000~1 000
000~63, 255 255
000~63 000
000~63 63
000~1 000
000~1 000
000~1 001
000~1 000
000~1 001
000~1 001
000~99 012
000~1 000
000~1 001
000~1 001
000~1 000
020~169 094
186~227 207
000~1 001
000~1 001
000~1 001
000~1 001
000~1 001
001~7, 255 255
000~1 000
000~1 000
000~1 001
000~7 002
000~7 002
000~1 000
000~1 000
000~255 000
000~255 000
000~255 000
000~255 000
Brief Description of Function and Comments
Leave default set 0.
Sets number of hours of no activity before auto shut off.
Set to 1 to enable auto turn on at power up.
Selects Tuning band.
Channel at turn-on (Set 255 to return to last channel before power off).
If set to 1, cannot tune from current channel.
Sets Volume level at TV turn-on(Set 255 to retain last volume level).
Sets minimum allowable volume setting.
Sets maximum allowable volume setting.
Set to 1 to disable mute function.
Disables menu navigation keys on display panel.
Set to 1 to enable Sleep Timer.
Set to 1 to enable On/Off Timers.
Set to 1 to enable Alarm.
Set to 1 to enable V-Chip functions.
Sets number of V-Chip(Parental Control) blocking hours.
Set to 1 to retain caption setting at power off.
If set to 0, limits direct access to favorite channels.
Set to 1 to change M.P.I. operation to OCV.
If set to 1, changes M.P.I. for some OCV boxes.
Selects poll rate for M.P.I.
Sets baud rate for M.P.I.
Set to 1 to enable Video 2 input.
Enables plasma panel DVI input port, set to 1 for DTV or 2 for PC. Set 0 to disable.
Set to 1 to enable display panel Component 1 input jacks.
Set to 1 to enable display panel Video 1 input jack.
For CRT-type TVs. Default set to 1 to automatically switch to Camport.
Sets the starting AUX source.
Set to 1 for M.P.I. AUX source reported as channel number instead of Channel 0.
Set to 1 to disable Channel-Time display.
Set to 1 to enable custom color for the Channel-Time display.
Chooses custom foreground color for the Channel-Time display.
Chooses custom background color for the Channel-Time display.
If set to 1 and channel override is 0, "NOT AVAILABLE" message is Displayed when
directly accessing a channel not in the favorite channel list.
If set to 1 and loss of M.P.I. communication occurs, TV tunes to Start Channel.
User programmable number, most significant byte.
User programmable number, most significant byte - 1.
User programmable number, most significant byte - 2.
User programmable number, least significant byte.
-17- LGE Internal Use Only