Related Manuals for LNC MW2200 Series
Summary of Contents for LNC MW2200 Series
- Page 1 LNC woodworking Machine Series Operation Manual Version：V1.1 Enable Intelligent Machine 寶元數控股份有限公司 LNC Technology Co., Ltd.
-
Page 2: Table Of Contents
LNC woodworking Machine Series Operation Manual Contents Contents ............................i Operation Panel ........................3 1.1. MW2200 Series ...................... 3 1.1.1. Main screen area ..................... 4 1.1.2. Mode area ....................... 5 1.1.3. Operating area ....................5 1.2. MW2800 / MW2900 Series ..................6 1.3. - Page 3 LNC woodworking Machine Series Operation Manual 4.2. Spindle Function ....................32 4.2.1. Spindle speed correlation ................32 4.2.2. Spindle cylinder ..................... 33 4.2.3. Spindle Suction Hood ..................34 4.3. Adsorption Function ....................36 4.4. Positioning ......................37 4.5. Dust-removal ......................38 4.5.1.
-
Page 4: Operation Panel
LNC woodworking Machine Series Operation Manual 1. Operation Panel At present, the woodworking machine system is divided into four major systems: MW2200, MW2800, MW2900 and MW5800. Among them, MW2800 and MW2900 are the same series. Therefore, they are only divided into three series actually, and each series has some differences with others. -
Page 5: Main Screen Area
LNC woodworking Machine Series Operation Manual 1.1.1. Main screen area The main screen area is mainly divided into three parts, as explained below: Caption： display the currently selected processing file, system mode, system status, selected page, time, and user level. -
Page 6: Mode Area
LNC woodworking Machine Series Operation Manual Button menu：: available for page switching and function selection. The left ^ (up arrow) represents the previous menu; the right > (right arrow) represents the next menu. 1.1.2. Mode area The mode ares is divided into 4 parts Mode switch: Supply 6 modes could be used, including MEM(Memory mode)., MDI(Manual... -
Page 7: Operating Area
LNC woodworking Machine Series Operation Manual alignment, Scheduling machining, Program Restart, User Switch, User Parameter, Parameter, System Update, click the button to switch to the function page directly. Operating area 1.1.3. The operation area divide into four parts. Direction Key: When manual operation (JOG/INCJOG), the selection buttons for each axial movement. -
Page 8: Mw2800 / Mw2900 Series
LNC woodworking Machine Series Operation Manual 1.2. MW2800 / MW2900 Series The MW2800 / MW2900 series is a model that provides a customized operation interface for the machinery factories, so it will have one more operation interface than other models; the following... -
Page 9: Group Description
LNC woodworking Machine Series Operation Manual 2. Group Description The system is divided into five groups, which are monitoring group, editing group, compensation group, diagnosis group and maintenance group, which are described as follows: 2.1. Monitoring Group This group is mainly used to monitor the machining information, motor load, program restart, MDI program input, machining settings of the machine and execution status of the machining program. -
Page 10: Edit Group
LNC woodworking Machine Series Operation Manual program. Processing information: Display the current system G code status, MST code status and the cutter compensation and cutter number in use. Load: Displays the current motor load status. This function is limited to bus drives. -
Page 11: Compensation Group
LNC woodworking Machine Series Operation Manual 2.3. Compensation Group This group is mainly used for coordinate system setting, tool compensation setting, automatic tool setting, centering function and tool changer setting. All buttons in this group are listed below: Tool management: Set the tool length compensation and wear compensation, that is, set the tool compensation table. -
Page 12: Diagnosis Group
LNC woodworking Machine Series Operation Manual 2.4. Diagnosis Group This group is mainly used to view system warnings, alarms, PLC ladder diagrams, IO point status, system information and operation history. All buttons in this group are listed below: Alarm: Displays the current alarm status of the system. -
Page 13: Maintenance Group
LNC woodworking Machine Series Operation Manual 2.5. Maintenance Group This group is mainly used to set system parameters, system backup, system upgrade, IO point setting, network setting, language setting and quick restore. All buttons in this group are listed below: ... - Page 14 LNC woodworking Machine Series Operation Manual System function: View the internal functions that are currently open in the system. ※This button needs to be switched to level 5 to appear. Project setting: Set the internal parameters corresponding to each type of system according to different system types.
-
Page 15: Screen Function Description
LNC woodworking Machine Series Operation Manual 3. Screen Function Description 3.1. Scanning Code to Open Files Function path: monitoring group > scanning code to open files 1. The function of scanning code to open files provides 5 sets of temporary storage functions for pre-scanning files. - Page 16 LNC woodworking Machine Series Operation Manual 寶元數控 LNC Technology Co., Ltd.
-
Page 17: Breakpoint Re-Start
LNC woodworking Machine Series Operation Manual 3.2. Breakpoint Re-start Function Path: Monitoring Group > Program Re-start The breakpoint re-start function is divided into 5 ways to search for the restarting point. Line number search: Search for the breakpoint based on the line number of the machining program entered by the user. - Page 18 LNC woodworking Machine Series Operation Manual The height above the breakpoint is set by user parameter 8052. After moving to the top of the breakpoint, machining startup is pressed again, and the program processing will start. Note： Before using the breakpoint to restart, it must be confirmed that the machine has returned to the origin, otherwise the function will not take effect (the set breakpoint cannot be found).
-
Page 19: File Management
LNC woodworking Machine Series Operation Manual 3.3. File Management Function Path: Edit Group > File Management This function is used to manage the machining procedures in the system, which mainly divided into three parts. Delete / rename / copy / select all / cancel select all 3.3.1. -
Page 20: Network Disk Import / Export
LNC woodworking Machine Series Operation Manual Network disk import / export 3.3.3. Users can directly import the machining program from the computer to the system or export the machining program in the system to the computer through the sharing method of network disk. -
Page 21: Scheduling Machining
LNC woodworking Machine Series Operation Manual 3.4. Scheduling Machining Function Path: Edit Group > Scheduling machining Scheduling Machining could be divided into standard version and item version. It could be switched through parameter, user could modify the parameter according to the required. - Page 22 LNC woodworking Machine Series Operation Manual Not use the scheduling: Do not use this function. Manual Start: When use scheduling machining function, the system will automatically open the next processing program in the schedule, after each execution of the processing program. But the use must manually press to start processing.
- Page 23 LNC woodworking Machine Series Operation Manual 1. Startup mode could be modified on screen, as the above image. (0:Not use, 1: Manual, 2: Automatic) ※ Note: This function need to be enabled, then the usage path will appear (show as below image), same for short-cut key.
-
Page 24: Automatic Tool Setting
LNC woodworking Machine Series Operation Manual Funtion is enable. 3.5. Automatic Tool Setting Function Path: Compensation Group > Automatic Tool Setting 1. The automatic tool setting function provides three tool setting modes as follows: Single-tool single workpiece: only one tool and one workpiece are processed during machining. -
Page 25: Tool Magazine Setting
LNC woodworking Machine Series Operation Manual iii. When using the tool compensation, the machining program must use the coordinate system set by the Z drop (The preset is G54). If different workpiece surfaces are used, the corresponding Z-drop coordinate system needs to be modified. -
Page 26: Carousel Style Tool Magazine Setting
LNC woodworking Machine Series Operation Manual Carousel style tool magazine setting 3.6.2. Function Path: Compensation Group > Next Page> Carousel style tool magazine If the Carousel style tool magazine is used, the related settings of tool magazine can be performed via this page. -
Page 27: Drilling Setting
LNC woodworking Machine Series Operation Manual Drilling setting 3.6.3. Function Path: Compensation Group > Next Page> Drilling Settings If the drilling tool magazine is used, you can set the drilling offset through this page. This screen provides 9 straight drill control interfaces, users can click the mouse or use the arrow keys + ENTER button to perform related motion control. -
Page 28: Backup
LNC woodworking Machine Series Operation Manual 3.7. Backup Function Path: Maintenance Group > Backup Use U-disk for system backup and restore actions: Backup: After inserting the USB flash drive, check the export to USB, select all data backup, press the transfer and select the U-disk folder. After selecting it, press OK to start the backup and wait for a few seconds until the system prompts the transfer to complete. -
Page 29: System Update
LNC woodworking Machine Series Operation Manual 3.8. System Update Feature Path: Maintenance Group > System Update Use a U-disk to update the system. Insert the U-disk into the system and press OK. The system will immediately mount the U-disk. After the mounting is successful, the U-disk content will appear. -
Page 30: Quick Restore
LNC woodworking Machine Series Operation Manual 3.9. Quick Restore Function Path: Maintenance Group > Quick Restore (It's required to switch the system level to 5) 1. The system provides quick restore and backup functions, allowing the machinery factory to set the factory default value when the machine is shipped. -
Page 31: Language Setting
LNC woodworking Machine Series Operation Manual 3.10. Language Setting Function Path: Maintenance Group > Next Page> Language Settings There are three languages in the system, which are Traditional Chinese, Simplified Chinese, and English. Select according to your needs. Use the up and down buttons on the keyboard to select the language and press ENTER. -
Page 32: Built-In Function Description
LNC woodworking Machine Series Operation Manual 4. Built-in Function Description 4.1. Automatic Loading And Unloading 1. The system provides three operating procedures of standard automatic loading, automatic uploading and automatic loading and unloading. 2. There are two ways to use automatic loading. The first type is M-code calling, the M-code number is M15, and the second type is one-key loading. -
Page 33: Spindle Function
LNC woodworking Machine Series Operation Manual 8341 [Loading function] Loading cylinder up and down in-place to check (0: no check, 1: up in-place, 2: down in-place, 3: up and down in-place) 8342 [Loading function] Loading and unloading in-place to check (0: no... -
Page 34: Spindle Cylinder
LNC woodworking Machine Series Operation Manual first spindle (seconds, -1: external signal notification) 8344 [Spindle function] Waiting time for arrival of zero speed of second spindle (seconds, -1: external signal notification) 8345 [Spindle function] Waiting time for arrival of zero speed of... -
Page 35: Spindle Suction Hood
LNC woodworking Machine Series Operation Manual Parameter Parameter Content 8070 Inspection form of the first spindle up and down in-place (0: no inspection, 1: up in-place, 2: down in-place, 3: up and down in-place) 8071 Inspection form of the second spindle up and down in-place (0: no... - Page 36 LNC woodworking Machine Series Operation Manual 8321 Spindle 2 suction hood up and down in-place inspection (0: no inspection, 1: up in-place, 2: down in-place, 3: up and down in-place) 8322 Spindle 3 suction hood up and down in-place inspection (0: no...
-
Page 37: Adsorption Function
LNC woodworking Machine Series Operation Manual 4.3. Adsorption Function 1. The system provides two types of adsorption, one is the partition adsorption control on the worktable surface; the other is the adsorption control of the entire worktable, as shown in the following diagram: 2. -
Page 38: Positioning
LNC woodworking Machine Series Operation Manual 9415 [M-code Setting] Vacuum pump 2 off 4.4. Positioning 1. The system provides a total of 6 sets of positioning controls, which can be used by the user for related positioning, or for side pushing or back pushing during the loading and unloading actions. -
Page 39: Dust-Removal
LNC woodworking Machine Series Operation Manual 4.5. Dust-removal Dust-removal of single station 4.5.1. 1. The dust-removal actions in the single-station system is the same as the uploading actions. When used, it is to call M17 or trigger one-key uploading button. - Page 40 LNC woodworking Machine Series Operation Manual 8325 [Dust-removal function] Dust-removal speed (KLU/MIN) 8326 [Dust-removal function] Allow dust-removal Z-axis coordinates (LU) during machining 8327 [Dust-removal function] Machine coordinate (LU) of the dust-removal starting point of station 1. 8328 [Dust-removal function] Machine coordinate (LU) of the dust-removal end point of station 1.
-
Page 41: Parameters Setting
LNC woodworking Machine Series Operation Manual 5. Parameters Setting 5.1. User Parameters Function Path: Maintenance Group > User Parameters (it's required to switch the system level to 5) Note： The contents of the user parameters will vary depending on the model version, but not all models of the woodworking machine are the same. - Page 42 LNC woodworking Machine Series Operation Manual waiting time of the spindle speed arrival, the waiting time of the spindle zero speed arrival, the inspection type of the spindle up and down in-place, etc. Speed：The related speed setting of the manual mode in the system, for example: F0 speed, JOG speed, fast forward speed, etc.
-
Page 43: System Parameters
LNC woodworking Machine Series Operation Manual M-code setting： The M-code value setting of the woodworking machine related functions, for example: positioning on and off, vacuum pump on and off, adsorption on and off, etc. If the user forgets the M-code of related function, it can also be viewed on this page. - Page 44 LNC woodworking Machine Series Operation Manual parameters of the system. Operation parameters: Set the relevant function parameters within the system, such as: preset feed rate, G31 related parameters, etc. System parameters: Set hardware connection parameters related to the system, such as hardware type (host type), CIO setting (bus IO board), etc.
- Page 45 LNC woodworking Machine Series Operation Manual Setting of each axis: Set the relevant parameters of each axial direction, for example: whether to use encoder, drive command format, origin searching method, etc. Gear ratio setting： Set parameters such as gear ratio and screw pitch for each axial direction.
- Page 46 LNC woodworking Machine Series Operation Manual Speed setting: Set the speed-related parameters for each axial direction, such as acceleration/deceleration time, G00 maximum speed, G01 maximum speed, and so on. The parameter page is divided into two parts, one for the servo axis and the other for the spindle.
- Page 47 LNC woodworking Machine Series Operation Manual Servo parameters: This is used for the bus driver, and the driver can be adjusted directly on the system. The pulse driver is not suitable (the MW2200A is a driver equipped with pulse). Advanced parameters: Advanced parameters: all parameters inside the system, if not required, it's unnecessary to use.