Page 4
POWER ON/OFF ........................121 RS232 COMMUNICATION SOFTWARE ..........123 Transmission line preparation ....................123 PC end installation (use LNC ReCON 232 software) ............... 124 NC end ............................126 Communication (RS232)-【 DNC file upload and download functions 】 ......140 3.4.1 Path Program Upload &...
But, this system has one standard panel that can be selected by tool machine producers. At below we will introduce LCD display device and MDIOP data input area.MDIOP operation area will be introduced at the Chapter Two. LCD MONITOR MDIOP VERTICAL LNC Technology Co., Ltd.
It will show the content of sub-function. Pressing the corresponding function button to select the wanted function. Additional function keys: (1). LCD switches(power ON/OFF) (2). PS/2 Keyboard, can connect with keyboard to control. (3). PS/2 Mouse, no support now. Main Figure 1.2-1 LCD Display Device LNC Technology Co., Ltd.
Page 7
LNC-Lathe New T6-Series CNC Operation MDIOP can divide into two sections. MDI DATA INPUT AREA:For users to input data. OP OPERATION AREA :For users to control operation. LNC Technology Co., Ltd.
Page 8
(with 1.Edit Mode2.Auto PROG PROG Mode3.Manual Mode) OFFSET OFFSET to set and to display tool offsest GRAPH GRAPH to draw tool path DGNOS DGNOS to display instance messge at DGNOS page PARAM PARAM to display parameter screen LNC Technology Co., Ltd.
Page 9
These characters, symbols and numbers are used for program editing and data key-in. There are some symbols that are diminished down at right-bottom of these keys. If want to use these symbols, please press SHIFT and the symbol key at the same time. C. Editing Keys: Editing Keys Editing Keys LNC Technology Co., Ltd.
Page 10
Note: this function will be valid under BIOS mode. Under edit mode, move cursor upper. ↑ To move cursor upper. Under edit mode, move cursor down. ↓ To move cursor down. Under edit mode, move cursor left. ← To move cursor left. LNC Technology Co., Ltd.
Page 11
To return cursor to the beginning of the sentence when editing Home Home program. To return cursor to the end of the sentence when editing program. When editing program, to move cursor right with 8 space. To cancel the previous character. LNC Technology Co., Ltd.
Users will be able to choose 6 screen displays by pressing those function keys which are 【ABS.】 , 【REL.】 , 【MAC.】 , 【RST】 and 【QUIT】 . There are some command information that will is displayed in those screens, which will be described separately as following: situation POS Function Display Screen LNC Technology Co., Ltd.
Page 14
RUN(H”M):Running time is the total cutting time after every booting, until the system shuts down, the time will be reset to be zero. You can also use【TIME CLEAR】 to make it to be zero. LNC Technology Co., Ltd.
Page 15
Using the program home (means the workpiece coordinate) to show tool’s current location, the absolute coordinate will be changed according to the movement of tool. This is called absolute coordinate Absolute coordinate is the program coordinate, which is [present value – tool offset = program value.] LNC Technology Co., Ltd.
Page 16
LNC-Lathe New T6-Series CNC Operation 【Time Clear】 Press 【Time Clear】to delete current total running time. 【Workpiece Clear】 Press 【Workpiece Clear】to delete current workpiece-make it to be zero. LNC Technology Co., Ltd.
Page 17
Press 【Initial Workpiece】to change current workpiece-make it to be ten. 【Max Workpiece】 Press 【Max Workpiece】 to change current max. workpiece-make it to be 100. When it comes to be 100 pieces, the controller will notify the workpieces have reached target. LNC Technology Co., Ltd.
Page 18
If you want to reset the coordinate value and to let X coordinate to 100.00, Y coordinate to 200.000 and Z coordinate to 300.000, only need to set X100, Y200, Z300. Then, pressing <INPUT> to reset the coordinate value immediately. LNC Technology Co., Ltd.
Page 19
Machine coordinate is the distance of the present position corresponding to the reference point Note:Each machine has its own reference point. For safety concern, please looking for the reference point whenever reboot machine before executing work. LNC Technology Co., Ltd.
Page 20
(C BITS 066 ~ 071)and MPG rates(REGISTER 014) will not change because of MPG interruption to show program coordinate. will not change because of MPG interruption. will change because of MPG interruption to chow exact position of machine. LNC Technology Co., Ltd.
Page 21
Press <confirm> to add space line, press <RESET> to make the cursor go back to head. Right side sub-function keys have below details. LNC Technology Co., Ltd.
Page 22
You can input specific keywords to search, if there are two searching words in the program, you can search the second one again. If the system can’t find the word, it will show no words finding. LNC Technology Co., Ltd.
Page 23
LNC-Lathe New T6-Series CNC Operation 【INS CYCL】 This function is to provide each working method in order to produce program rapidly. After pressing【INS CYCL】, the screen will be as below: Pressing “Input” after selecting working method: LNC Technology Co., Ltd.
Page 24
LNC-Lathe New T6-Series CNC Operation To press “Input” key to enter into the following Figure page. To move the highlighter to each parameter column and then press <INPUT> key LNC Technology Co., Ltd.
Page 25
LNC-Lathe New T6-Series CNC Operation Program code page is as following after pressing 【OK】 LNC Technology Co., Ltd.
Page 26
After pressing right side【LPOSITION】function key, you can input the line number directly at dialogue box input program and press enter to make the cursor to move to this location, as below: (Note)Users can not do cycle start under edit mode. LNC Technology Co., Ltd.
Page 27
Please refer to the below figure. Note: After marking, you can use COPY and LDELET to do multi-line program editing. 【UNMARK】 To cancel previous marking sign. Note: If you will not use【MARK】anymore, please use【UNMARK】to prevent mistakes. LNC Technology Co., Ltd.
Page 28
【COPY】 To copy the marked program in local range. 【CUT】 To cut down the marked program in local range. 【BIND】 To paste on the program codes that are copied or cut at previous time. LNC Technology Co., Ltd.
Page 29
【Teach Mode】/【Delete Teach】 Press this button to show ABS/REL/MAC at the down side for reference. At the right side of sub-function keys will show【INSERT COORDINATE】for users to insert current location’s absolute coordinate quickly, detail is as below: LNC Technology Co., Ltd.
Page 30
Pressing【BGPROG】to enter into background editing mode under auto mode. Background editing allows users to edit another part program while executing one part program in auto mode. Editing method and the environment of doing present program in editing mode are totally the same. Note: Background file is 08999 permanently. LNC Technology Co., Ltd.
A detailed description is as following. 【FILE】 Solution 1 Able to use direction key to choose the wanted open file after entering into the file management screen. Also, users are able to open a file after pressing <INPUT>. LNC Technology Co., Ltd.
Page 32
After pressing open file selection button, a dialog box will occur on the screen. Please choose or key-in the wanted open file name and then pressing <INPUT> to open the file. Or in the dialog box mode to press left or right button to switch line for cursor. LNC Technology Co., Ltd.
Page 33
Such as below: Or in the dialog box mode to press left or right button to switch line for cursor. To offer different path switch methods. LNC Technology Co., Ltd.
Page 34
If only enter file name, then the file path is the system default value. As below: Figure 1.4-1 Screen of Key-In Destination File Name LNC Technology Co., Ltd.
Page 35
Press select to choose check box and press confirm later. You can also use【no select】 【select all】 【no select all 】to manage file. LNC Technology Co., Ltd.
Page 36
Pressing on this sub-function button, a file delete dialog box will appear on the screen. Please choose the wanted delete file in that dialog box. After complete deleting, users can use Program Table to confirm. Figure 1.4-3 【DEL】screen LNC Technology Co., Ltd.
Page 37
After pressing confirm, the system will pop up hint message to double confirm if you really want to delete these files. You can also use【no select】 【select all】 【no select all 】to manage file. LNC Technology Co., Ltd.
Page 38
Pressing confirm button to enter into the file rename window. 2. To enter the destination file name in the rename windows and then to press confirm button. After rename complete, users will be able to use program list to confirm. LNC Technology Co., Ltd.
Page 39
Users are able to set the part program menu by using this dialog box or by entering work path directly. Note: The name of the directory can not be the same with our current controller’s files. Figure 1.4-4 Screen when Setting Part Program Menu LNC Technology Co., Ltd.
Page 40
【FILE DOWNLOAD】 It means sending file from PC end to NC end, and also command NC end to save the file at NC end’s external device. Note:As for detail information, please refer to RS232 communication software chapter. LNC Technology Co., Ltd.
Page 41
【FILE UPLOAD】 It means sending file from NC end to PC end, and also command PC end to save the file at PC end’s external device. Note:As for detail information, please refer to RS232 communication software chapter. LNC Technology Co., Ltd.
You will see program content at the upper side of the monitor. The program that was executing right now will be highlighted. At the down side of the monitor is the absolute coordinate, dist to go,M/S/G/T CODE, exact speed and so on. LNC Technology Co., Ltd.
Page 43
LNC-Lathe New T6-Series CNC Operation 【Current Single Block】 To display the current single block. 【Next Single Block】 To show the next single block. LNC Technology Co., Ltd.
Then, pressing Cycle Start key and the command will be executed and related data will be displayed. Using this method to do test running is much safer and more time-efficiency. Also systems provide【CLR】 【DELLN】to help users. LNC Technology Co., Ltd.
Clicking the【COMM】function button to receive and transmit programs between the controller and other PCs. Operation and description of sub-function buttons 【COMM】 and【SETT】are as following. Figure 1.4-5【COMM】 screen Storage Device [Send] [Open] File [Save] File File File [RS232 Figure 1.4-6 Files Transmitting/Receiving Figure between Controller and Other PCs LNC Technology Co., Ltd.
Page 46
【CLEAR】Giving up and clearing program files in the windows. 【RESET】Giving up file transmitting and resetting communication deal in order to build up connect with RS232. Note:Detail information; please refer to RS232 communication software chapter. LNC Technology Co., Ltd.
【INC】Input by increase value, ex: value 0.500, input-0.1, and it will show 0.400. 【NORUNT】Input by normal unit,ex: value 0.500, input 1, and it will show 1.000. 【MINUNT】Input by minimum unit,ex: value 0.500, input 1, and it will show 0.001. LNC Technology Co., Ltd.
Page 48
X Axis Wear :X Axis Wear Offset Z Axis Wear :Z Axis Wear Offset Program Basic Point X axis outline Imaging tool offset Exact tool X axis wear Z axis wear offset offset Z axis wear offset Figure 1.5-3 LNC Technology Co., Ltd.
Page 49
- - - Cursor Lock, can’t input Ready Preparation Not in the program processing. - - Complete Cycle Start No wear offset during traveling. - Feedhold Password protection Off Blocks Pause Tool Offset Password Setting Chart LNC Technology Co., Ltd.
Z Axis Tool Length:Z Axis Outline Offset Users can input change data under complete prepared MDI mode. But for X axis and Z axis tool length, users can use ”MXxx” and ”MZzz” to do offset setting. LNC Technology Co., Ltd.
Method 2: key-in the estimating value. Please key-in “MXxx MZzz” first and then pressing【ENTER】 to update the new entry value into the estimating value column. So estimating value = entry value. Shift value = machine coordinate value – entry value - G54~G59 shift – (wear offset value + geometry offset value) LNC Technology Co., Ltd.
<PAGE↓> and <PAGE↑> key. Or input @100 at input line and press enter, it will start to search @100 automatically. Move the highlighter to the wanted modify position and then to press <INPUT> key after entering the wanted value. Figure 1.5-6 Local Variables of MACRO Variables LNC Technology Co., Ltd.
Page 53
LNC-Lathe New T6-Series CNC Operation Figure 1.5-7 Global Variables of MACRO Variables LNC Technology Co., Ltd.
:Set X Axis’ machine coordinates value into working coordinates which the cursor stops. Z SET :Set Z Axis’ machine coordinates value into working coordinates which the cursor stop. C SET :Set C Axis’ machine coordinates value into working coordinates which the cursor stop. LNC Technology Co., Ltd.
When the yellow cursor occurs at the head parameter column, pressing【ENTER】key to switch the screen to the head parameter screen. After key-in the needed head parameter data, pressing 【ENTER】key to switch the screen back to the main function screen. Then, a blue “DEFINE” will occur on the head parameter column. LNC Technology Co., Ltd.
Page 56
Then, blue characters, “Define”, will appear on the geometry define column. After the above seven steps, users can press 【SAVE】 to save the project. Or, pressing【NC Gear Shifting】to produce the working path program. LNC Technology Co., Ltd.
【ENTER】 at this column. 4 types of tool number, which are A type for drilling tool, B type for profile lathe tool, C type for grooving tool, D type for screwing tool. Number means the tool number from the tool list on the tool setting page. LNC Technology Co., Ltd.
Page 58
※ PROC INS:insert a new program to the previous row of the row where the yellow cursor occurs. ※ PROC CPY:copy a row of program where the yellow cursor occurs to the next row of the copied row. ※ PROC DEL:delete all procedures where yellow c sor occurs. LNC Technology Co., Ltd.
Page 59
※ NEW:building a new project name and the screen will switch to the main function screen after confirm the key-in project name. ※ DELETE:deleting a project where yellow cursor occurs. ※ RETURN:switching screen to the main function screen. LNC Technology Co., Ltd.
Page 60
【OPEN】 key at screen bottom to cancel opening new file. Pressing 【CANCEL】 key after pressing 【DEL】 key at screen bottom to cancel deleting file. ◎ Screen of Working Method is as below: Figure 1.6-3 Working Method Page LNC Technology Co., Ltd.
Page 61
⊙ OSEW:external thread cutting. Cutting thread horizontally and selecting feeding method according to the using method. ⊙ ISEW:internal thread cutting. Cutting thread horizontally and selecting feeding method according to the using method. LNC Technology Co., Ltd.
Page 62
※ Tool Clear Dialog Box at Screen Bottom: able to display and edit 10 sets of data. Users need to key-in different columns according to different working methods. The description of each column is as below: LNC Technology Co., Ltd.
Page 63
Figure 1.6-5 Corresponding Position Figure of Imagery Tool Tip Point and Tool Noise Center Point ⊙ Tool Radius: tool noise radius. The below Figure is the tool tip after scaling in. radius Figure 1.6-6 Scale-In Figure of Tool Tip LNC Technology Co., Ltd.
Page 64
⊙ Rotary Direction:Spindle rotary direction, clockwise (CW) or counter clockwise (CCW) 【Function Keys at Bottom at the Screen】 ※ Selection: select the needed tool parameter data, tool number at the upper screen indicates the selected tool number. ※ Return: switch to the main function screen. LNC Technology Co., Ltd.
Page 65
⊙ F RPM:when the feed unit is selected as 1, users must key-in any value that is larger than 0 into this column. ⊙ S TYPE:0 means using fixed cutting speed, 1 means using fixed rotating speed. LNC Technology Co., Ltd.
Page 66
⊙ T Code: actual tool number on turret. 【Function Keys at Screen Bottom】 ※Return: switch to the main function screen. 【Function Keys at Right of the Screen】 None. ◎ Cutting Parameter is as the below screen Figure 1.6-9 Cutting Parameter Page LNC Technology Co., Ltd.
Page 67
⊙ TIME: drilling dwell time. ⊙ TYPE: the lathe-cutting mode selection. ⊙ DRILL: pre-drilling of internal lathe-cutting. 【Function keys at Screen Bottom】 ※ Return: switch to the main function screen. 【Function Keys at Right of Screen】 None. LNC Technology Co., Ltd.
Page 68
The number should be the tool NO. from the tool clear list of the screen. ※ Geometry Drilling Column: ⊙ TOOL X:tool point diameter coordinate ⊙ TOOL Z:tool point Z coordinate ⊙ START X:starting drilling hole point diameter coordinate, 0. ⊙ START Z:start drilling hole point Z coordinate. LNC Technology Co., Ltd.
Page 69
Figure shape at inside of the dialog box at screen center. ※ Return:pressing the【SCALE】key at bottom of the screen to switch to the geometry drilling screen. ◇ Screen of Geometry Profile is as below Figure 1.6-11 Geometry Profile Page LNC Technology Co., Ltd.
Page 70
※ CCW:drawing a arch by counter clock-wise direction. Users are able to key-in data after pressing this key. Pressing【OK】 key at screen bottom to complete this new adding action. ※ Delete:delete the last line of the present profile. LNC Technology Co., Ltd.
Page 71
※ Tool NO.:display the selected tool NO. of the currently editing procedure. 4 types of tool NO. Type A for drilling tool, Type B for pattern tool, Type C for grooving tool, and Type D for thread tool. The number should be the tool NO. from the tool clear list of the screen. LNC Technology Co., Ltd.
Page 72
※ Fittest Size:pressing 【WINDOW】at screen bottom for this function to be occur. This will return to the original size of the Figure shape at inside of the dialog box at screen center. ※ Return:pressing【SCALE】key at screen bottom to switch the screen to the geometry grooving screen. LNC Technology Co., Ltd.
Page 73
NO. from the tool clear list of the screen. ※Cutting Parameter Column: ⊙ START:start tapping diameter coordinate ⊙ START Z:start tapping Z coordinate ⊙ END:start tapping diameter coordinate ⊙ END Z:end tapping Z coordinate ⊙ CREST:thread height LNC Technology Co., Ltd.
Page 74
※ Fittest Size:pressing 【WINDOW】at screen bottom for this function to be occur. This will return to the original size of the Figure shape at inside of the dialog box at screen center. ※ Return:pressing【SCALE】key at screen bottom to switch the screen to the geometry thread screen. LNC Technology Co., Ltd.
Page 75
Not enough memory Curve not block Curve section over 20 Lathe-cutting procedure over 10 Total tool number over 50 Tool parameter setting not reasonable Cutting parameter setting not reasonable Not able to open file Diskette is full LNC Technology Co., Ltd.
Page 76
Max. effective setting error of external lathe cutting Max. effective setting error of internal lathe cutting Internal lathe-cutting setting error Grooving tool width setting error or smaller than 0 Tool type setting error Tool setting over 50 sets Open file failure LNC Technology Co., Ltd.
Page 77
Leading cutting value is smaller than 0 Tapping distance setting error or smaller than 0 Min. cutting depth setting error Thread type setting error Profile lathe-cutting define(G01,G02.G03 assign error) G02G03 define point can’t be arch Drilling lathe-cutting parameter(drilling type selection error) LNC Technology Co., Ltd.
Page 78
Use external lathe-cutting tool error Use internal lathe-cutting tool error Use external grooving cutting tool error Use internal grooving cutting tool error Use face-grooving tool error Use internal lathe-cutting tool error Use external lathe-cutting tool error LNC Technology Co., Ltd.
Page 79
LNC-Lathe New T6-Series CNC Operation Error Code Message Use drilling lathe-cutting tool error LNC Technology Co., Ltd.
Note 1: Cursor is green color, G00 is red color and G01, G02 and G03 are yellow color. Note 2: Cursor is green color, G00 is blue color, and G01, G02, and G03 are pink color. Center line is bright-green color. LNC Technology Co., Ltd.
Figure 1.7-2 Main Screen of the Windows Definition Drawing Surface:the using coordinate view angles are (1=XY, 2=YZ, 3=ZX, 4=YZ, 5=ZY, 6=XZ, 0=XYZ) when key-in into the path display screen. GRAPH GRAPH 1=XY 5=ZY 2=YZ 6=XZ 3=ZX 0=XYZ 4=YX LNC Technology Co., Ltd.
Page 82
0:start auto preview function. When users change to path page, system will start to do preview automatically and draw program path. 1:close auto preview function . When users change to path page, system will not start to do preview automatically and will not draw program path. LNC Technology Co., Ltd.
【ALARM】Alarm message will occur when there is any problem in system running. This will make the system stop running and also will display the alarm message on the screen. When the problem is solved, must press <RESET> in order to release the situation. LNC Technology Co., Ltd.
Page 84
LADDER program. The system will stop running when the system sends out the warning message and the warning message will be displayed on the screen. When the problem is solved, must press <RESET> to release the warning. LNC Technology Co., Ltd.
Page 85
LNC-Lathe New T6-Series CNC Operation 【HISMSG】System version and program debugging message will occur. This page displays the system current running condition. 【LOGHST】Able to display system’s all alarms/alarm records, even delete the alarm, the records will not disappear. LNC Technology Co., Ltd.
Pressing the sub-function button 【I BIT】, the type will be displayed at the upper left column of the screen.); < 單 PAGE↑> and < PAGE↓> keys are used to control the page changing of this【I BIT】sub-function. 向 軸 單 向 LNC Technology Co., Ltd.
Users are able to add number on the wanted searching English characters, such as I, O, C, S, A, R, TM and est. in 【LAD】 entering row. Pressing 【INPUT】 to start searching the position of those characters. For example: key-in TM001 or TM1 to search for the position. LNC Technology Co., Ltd.
Page 89
LNC-Lathe New T6-Series CNC Operation Press【CNT】to check data as below. Press【REG】to check data as below. LNC Technology Co., Ltd.
Page 90
LNC-Lathe New T6-Series CNC Operation Press【CNT】 、 【REG】 、 【DRG】 、 【TMR】to see data as below. Press【TMR】to check data as below. LNC Technology Co., Ltd.
Users are able to get the possible error message from the solving method in order to check and to solve the problem. The HOME DOG condition at the top of the windows indicates that if the value of each axis is 1, the present position of each axis is on the HOME DOG. LNC Technology Co., Ltd.
Working Piece:When CNC has read M02, M03 or other M codes, the system will adding up the working piece automatically. Using 【RST】 + 【PARTCONT】 will return the working piece number back to zero. Figure 1.8-8 Working Parameter Page LNC Technology Co., Ltd.
EMG-STOP key. At this time, a screen which function is selected by the cursor (like Figure 2.10-3) will occur. This screen allows users to select the wanted working item. Each function is listed as below: Figure 1.8-9 System Upgrade Screen LNC Technology Co., Ltd.
Page 95
SYSTEM UPGRADE This function offers two ways for update: general disk/RS232 transmission. Please install LNC Technology Co., Ltd. latest version software if choosing this function. Pressing【YES】, the installation screen will occur. There is installation program instruction during installation so you only need to follow the instruction to upgrade the system.
Page 96
System will double confirm if you want to do upgrade, make sure if you really want to do upgrade and press 【OK】 Then system will turn to DOS page as below to show current version and update version, press【Y】and system will process upgrade automatically. LNC Technology Co., Ltd.
Page 97
LNC-Lathe New T6-Series CNC Operation Please wait, file preparing. System upgrade is completed, please press any key to reboot and you can use new version software later. H.D CHECK (DISK DIAGNOSIS) LNC Technology Co., Ltd.
Page 98
If users do not choose, the system will use the default C drive. There are 4 types of working items for users to choose: (1)anti-virus (2)hard drive scanning (3)hard drive reset (4)exit Figure 1.8-12 Hardware Checking Function Selection LNC Technology Co., Ltd.
Page 99
Users are able to key-in the dialog box of the backup copy path after pressing the confirm button. Pressing the confirm button after users key-in or select the wanted backup parameter to complete the parameter backup function. LNC Technology Co., Ltd.
Page 101
If executing this function. Selecting the “renew parameter” item from the popup dialog box after pressing confirm button. A dialog box of key-in parameter renew source path occurs after pressing confirm button. Figure 1.8-15 Reminding Users to Reboot after Key-in Parameter LNC Technology Co., Ltd.
Page 102
LNC-Lathe New T6-Series CNC Operation FONT: After user selects a designated text font source, please pressing【OK】 Figure 1.8-16 Text Font Installation Source Page LNC Technology Co., Ltd.
Figure 1.9-1 Soft Panel Function Screen Using these corresponding functions switches separately. The function picture changes from red to green on the screen, which means the function is enabled. Turning it back again to disable the function LNC Technology Co., Ltd.
Page 104
But MPG will not according to it. faster then program feetrate. When MPG stops, the program will also stop. MPG CCW will not control program. Ignore any command from Z Axis Process any command from Z Axis. Z Ignore LNC Technology Co., Ltd.
R(Effective after RESET) ⊙(Effective after rebooting) Empty(Effective immediately) User must fully understand each parameter’s definition before modifying any parameter. Two types of user status: end-user and machine maker. Different user status will have different sub-function keys. LNC Technology Co., Ltd.
LNC-Lathe New T6-Series CNC Operation 1.10.2 USROPT Press【USROPT】and enter to【PARAM 1】page, there are 40 sets of parameters. The way to change the parameter is the same to system parameter, please refer to last chapter. Figure 1.10-1 USROPT LNC Technology Co., Ltd.
Page 107
LNC-Lathe New T6-Series CNC Operation Press【PARAM 2】page, there are 40 sets of parameters. The way to change the parameter is the same to system parameter, please refer to last chapter. LNC Technology Co., Ltd.
Any of these two conditions above is effective, system will judge it as due, at this time,(CYCLE START) function will not be effective. If you press(CYCLE START)after due date, the system will show ALARM message as below: 【OP 1017 system has expired, please contact your machines makers.】 LNC Technology Co., Ltd.
Controller Name:This is the controller’s name in the net, different controllers will have different names, and the name can not be the same with the PC’s. Its default name will be LNCDOS, therefore if there are many controllers in the same Net area, you will need to modify this section. LNC Technology Co., Ltd.
Page 110
Note:Nwlink NetBIOS, this protocol can’t be drove, otherwise the connection will fail. WINDOWS-98 WINDOWS-2000 WINDOWS-XP B.Confirm [PC name] and [Work Group] is correct setting.(Controller side’s PC name and work group name should be the same, and vice versa) LNC Technology Co., Ltd.
Page 111
LNC-Lathe New T6-Series CNC Operation WINDOWS-98 WINDOWS-2000 WINDOWS-XP C.To share PC end’s file, and make sure the share name is the same with controller side. WINDOWS-98 WINDOWS-2000 WINDOWS-XP LNC Technology Co., Ltd.
Page 112
Use【ReCON】to connect and the setting of PC end: Use ↑↓← → to move direction buttons to move to wanted line and input data into, press INPUT and you will see data was shown on the screen. LNC Technology Co., Ltd.
Page 113
Press【N】 :Means you are not allowed this IP’s PC to connect with controller, next time controller will not accept any request from this IP. Press【CANCEL】 :Means you cancel this time’s connection from PC end. Next time, when PC end wants to connect, it will show the same dialogue to ask your permission. LNC Technology Co., Ltd.
Page 114
PC connected to controller right now, if there is IP address onit, it means right now has connecting PC. But if not, it means there is no connection. As for ReCON connection detail, please refer to RECON relating setting chapters. LNC Technology Co., Ltd.
Machine Maker If you press【CHGUSR】under Machine maker’s status, the password you changed will be under Machine Maker. 1. From End-User to enter in Machine Maker’s password. 2. Under Machine Maker Status to change parameter’s password. LNC Technology Co., Ltd.
Press【NC. SYS】 and go to parameter setting page, there are several sub-function keys, including 【SRVO】 、 【MAC】 、 【SPDL】 、 【MPG】 、 【COMP】 、 【HOME】 、 【OPER】and【INCOMP】 When changing to Machine Maker, you will need to input default password 『0000』 while log in and change parameters. LNC Technology Co., Ltd.
For example, pressing +X key under JOG mode, it will move to +X direction, and release this key, it will stop moving. Other axis has the same functions. Press +X under ZRN mode, X axis will go plus direction to return home. Other axis has the same functions. MODE SELECT LNC Technology Co., Ltd.
Page 119
Meanwhile if customer use servo system with absolute encoder, when you return home you don’t have to reach DOG, you can directly go back to home and complete this procedure. LNC Technology Co., Ltd.
UP+ and DOWN- buttons. Rate can be from 0% to 120%. For example, after giving a command as M3 S1000, and adjust button is at 120%, the exact rotation will be 1200PRM.And if you set it to be 10%, press 100% button, and the exact rotation speed will become 1000PRM. LNC Technology Co., Ltd.
When system cycle start, MPG can control the operation and change the program coordinate to move with servo axis. When MPG runs faster, the program will be executed faster, but it will be faster then the program federate command. When MPG stops, the program will stop LNC Technology Co., Ltd.
Page 122
Note: It is possible that over traveling situation occurs when “NOT Ready” condition occurs without any prediction. Please put the over traveling condition into the checking item when searching for reasons LNC Technology Co., Ltd.
If not returning back to home, users can switch the “Reference Need to OFF” on the Users Define screen. By doing this, program will be able to execute without returning back to home. LNC Technology Co., Ltd.
100mm/min. But, if adjust this button to 50%, the actual feed rate is only 50mm/min. This button works for servo feedrate under JOG mode on multiple machines. When Dry Run mode is effective, this button will adjusts the feedrate too LNC Technology Co., Ltd.
When users press power ON, it will turn on the CNC controller’s power, on the contrary, when users press power OFF. System will wait for a while to release servo’s electricity and shut down controller’s power. LNC Technology Co., Ltd.
Confirm COM PORT:Confirm if BIOS is ON and can operate COM port (ENABLE COM PORT) Confirm specification of Transmission line: Usually PC side has two kinds of com ports-9 pin and 25 pin, LNC controller was fixed to use 9 pin types, so you will have two ways to follow.
LNC-Lathe New T6-Series RS232 COMMUNICATION SOFTWARE PC end Installation (Use LNC ReCON 232 Software) Clicks CD> Software\ ReCON-232 V1.25.0010, or double click setup.exe icon, the driver will start to install automatically. According to Wizard’s direction to follow next step or click the items to continue.
Page 129
LNC-Lathe New T6-Series RS232 COMMUNICATION SOFTWARE If you want to re-set system, you can press stop to end up transmission and press start again. Press EXIT to leave software. LNC Technology Co., Ltd.
Page 131
Steps are as below: 1.Edit RS232 setting at controller and PC end, and make sure they are coordinate. 2.Use PROG group, change to EDIT mode. 3.Go to 【DIRMNG】, select 《RS232》DNC PROGRAM and press OK. LNC Technology Co., Ltd.
Page 132
LNC-Lathe New T6-Series RS232 COMMUNICATION SOFTWARE 4. Select 1. LNC ReCON 232 software to upload. 5.Go to PC end disk and select DNC file, press【YES】 LNC Technology Co., Ltd.
Page 133
LNC-Lathe New T6-Series RS232 COMMUNICATION SOFTWARE 6.Now the file will turn to be RS232 and change mode to MEM. 7.Press【CYCLE START】, start to do DNC. LNC Technology Co., Ltd.
Page 134
LNC-Lathe New T6-Series RS232 COMMUNICATION SOFTWARE 8.Select 2. General software to upload. (Use SM8 sample) 9.Now the file will turn to be RS232 and change mode to MEM. LNC Technology Co., Ltd.
Page 135
11.Before press Send button at PC end, please make sure NC end is at stand by>Cycle-Start mode. In other words, receiver must be prepared, so the sender can send out files, or after sending, press Cycle-Start to do DNC. LNC Technology Co., Ltd.
Page 136
When "Transfer is complete" shows on PC end, it means the transmission is complete. Below is the window of PC end’s communication setting page.Go to [Configure]> [Edit Machine Settings] choose a correct setting to connect with LNC. LNC Technology Co., Ltd.
Page 137
LNC-Lathe New T6-Series RS232 COMMUNICATION SOFTWARE Press [NEW] LNC Technology Co., Ltd.
Page 138
LNC-Lathe New T6-Series RS232 COMMUNICATION SOFTWARE Description could be LNC-RS232 (or defined by user) Go to [Comm]>Communication setting, other tables can be the same. LNC Technology Co., Ltd.
Page 139
Press [Save], save the file at SM8>C:\SM8 and name it as LNCRS232. You only need to edit machine setting at the first time, after that all you need to do is to select the same setting. LNC Technology Co., Ltd.
Page 140
LNC-Lathe New T6-Series RS232 COMMUNICATION SOFTWARE Go to [File]> [Edit Machine Settings] Select the setting of [LNC-RS232] that you just made. LNC Technology Co., Ltd.
Page 141
LNC-Lathe New T6-Series RS232 COMMUNICATION SOFTWARE At this time, [Edit Settings] button will pop out, you will see COM1,96□8,EVEN,8,1 at down side. Press file and go to [Edit]> [Open Code File] LNC Technology Co., Ltd.
Page 142
LNC-Lathe New T6-Series RS232 COMMUNICATION SOFTWARE Select the file that you want to do DNC transfer and press OK. Press [Send] LNC Technology Co., Ltd.
Page 143
LNC-Lathe New T6-Series RS232 COMMUNICATION SOFTWARE Start to upload, press 【CYCLE START】and start to do DNC. When you see "Transfer is complete" at PC end, it means the transferring is ok. LNC Technology Co., Ltd.
Edit RS232 setting at controller and PC end, and make sure they are coordinate. Use PROG group, change to EDIT mode. Go to 【DIRMNG】 and choose the file that you want to transfer to PC end and press [DOWN LOAD] Select 1. LNC ReCON 232 software to upload. LNC Technology Co., Ltd.
Page 145
LNC-Lathe New T6-Series RS232 COMMUNICATION SOFTWARE Choose the file O5678 you want to download from controller and press OK Set PC end’s file path and upload file name. (You could choose new name or save at old file. LNC Technology Co., Ltd.
Page 146
LNC-Lathe New T6-Series RS232 COMMUNICATION SOFTWARE Check if file name is ok at NC and PC end, press OK to upload. LNC Technology Co., Ltd.
Edit RS232 setting at controller and PC end, and make sure they are coordinate. Use PROG group, change to EDIT mode. Go to [DIRMNG] and choose the file that you want to transfer to PC end and press [UP LOAD]. Select 1. LNC ReCON 232 software to upload. LNC Technology Co., Ltd.
Page 148
LNC-Lathe New T6-Series RS232 COMMUNICATION SOFTWARE Select save path and upload name at PC end. At NC end, you could input new name or save at the same file. LNC Technology Co., Ltd.
Page 149
LNC-Lathe New T6-Series RS232 COMMUNICATION SOFTWARE Confirm and press [OK] Upload file successful. LNC Technology Co., Ltd.
Use PROG group, change to EDIT mode. Go to【DIRMNG】and choose the file that you want to transfer to PC end and press [DOWN LOAD]. Select 1. General software to upload. Go to Communication page and press [COMM] at the down right side. LNC Technology Co., Ltd.
Page 151
LNC-Lathe New T6-Series RS232 COMMUNICATION SOFTWARE Go to RS232 COMMUNICATION file download page. LNC Technology Co., Ltd.
Page 152
LNC-Lathe New T6-Series RS232 COMMUNICATION SOFTWARE Press [SEND], start to transfer files from NC end to PC end, select name and press [OK] NC end’s file will start to transfer to PC end. LNC Technology Co., Ltd.
Page 153
LNC-Lathe New T6-Series RS232 COMMUNICATION SOFTWARE After communicate setting at PC end, open a blank file for transferring, press [Receive], confirm to deliver file, press [Confirm]. After transfer is completed, press [OK] LNC Technology Co., Ltd.
Edit RS232 setting at controller and PC end, and make sure they are coordinate. Use PROG group, change to EDIT mode. Go to 【DIRMNG】 and choose the file that you want to transfer to PC end and press [UP LOAD]. Select 1. General software to upload. LNC Technology Co., Ltd.
Page 155
LNC-Lathe New T6-Series RS232 COMMUNICATION SOFTWARE Go to communication page and press [COMM] at the down right side. Go to RS232 communication. LNC Technology Co., Ltd.
Page 156
RS232 COMMUNICATION SOFTWARE After communicate setting at PC end, open an old file for transferring, press [Send], confirm to upload file, press [OK], upload complete . PC end will start to receive the files from NC end automatically. LNC Technology Co., Ltd.
Page 157
LNC-Lathe New T6-Series RS232 COMMUNICATION SOFTWARE After receiving, press SAVE with a new name or SAVE at the same file. Press OK, Copy complete. LNC Technology Co., Ltd.
Page 158
LNC-Lathe New T6-Series RS232 COMMUNICATION SOFTWARE 10. Go to [DIRMNG], you could see O0312 has saved at [DIRMNG] 11. At last, check file amount and graphic preview; see if there is any mistake. LNC Technology Co., Ltd.
COM1 and make sure other setting is the same with NC end. [Device Manager] > [Start] > [Control Panel] > [System] > [Hardware] > [Device Manager] > [Ports] or [COM&LPT], you can find detail as below. LNC Technology Co., Ltd.
Page 160
LNC-Lathe New T6-Series RS232 COMMUNICATION SOFTWARE LNC Technology Co., Ltd.