NANOLUX SUMMIT 1000W Operating Manual

a
FIXTURE HANGING
Fixture hanging equipment included with unit for necessary mounting.
1. Attach the ring bolt to the reflector support frame.
2. Hang the fixture in the desired locations.
TROUBLESHOOTING
Symptom Cause Corrective Action
Incorrect Lamp
Make sure lamp knob is set to proper setting for your lamp.
Knob Selection
Incorrect Dimming Make sure dimming knob is not set to NCCS-RTU/
Knob Selection NCCS-0-10V if you are not using that function.
Incorrect Lamp Verifty that bulb is installed correctly, and the electrical
Installation
contacts in ceramic bulb holder are not damaged.
Replace lamp with a known working lamp. Refer to
Lamp does
Faulty Lamp
"Lamp Replacement and Hot Restrike" section.
not turn on.
Use voltmeter to confirm incoming voltage is within
AC90V-280V, or plug ballast into a different socket that
Faulty Power Input
you know is working.
Incorrect Controller
Make sure controller is programmed to turn the lights on.
Programming
Remove NCCS-RTU/NCCS-0-10V control, set dimming
Faulty Control Input
knob to 100%, and see if that solves problem. If so, the
error is with the control, not the ballast.
Incorrect Lamp
Make sure lamp knob is set to proper setting for your lamp.
Knob Selection
Replace lamp with a known working lamp. Refer to
Lamp turns Faulty Lamp
"Lamp Replacement and Hot Restrike" section.
on, but
shuts off.
Remove NCCS-RTU/NCCS-0-10V control, set dimming
Faulty Control Input knob to 100%, and see if that solves problem. If so, the
error is with the control, not the ballast.
Incorrect Lamp
Lamp tries
Make sure lamp knob is set to proper setting for your lamp.
Knob Selection
to strike but
never fully
Replace lamp with a known working lamp. Refer to
Faulty Lamp
comes on.
"Lamp Replacement and Hot Restrike" section.
SCOPE OF USE AND MAINTENANCE
b
● Comply with local installation regulations.
● Only compatible with Nanolux DE HPS/MH 600W/1000W，CMH 1000W/630W
lamp preventing damage to the lamp and your ballast.
● Store the fixture in a dry and clean environment, with an ambient tempera-
ture of -10 ~ 40 °C and ambient humidity of less than 90% RH. It is recom-
mended to store it no more than (6) months. If it is expired (6) months,
please have an experiment on it to insure the secure operation.
● Please keep products safe. Avoid mechanical pressure, excessive vibration
and dropping the unit during the process of assembly to protect the
reflector and lamp.
● Keep away from water, oil and organic solvent, or it will decrease the
reflectivity and have the potential risk of electric leakage.
● All equipment, devices and machines shall be effectively grounded.
● Do not touch hot ceramic socket.
● Disconnect the mains first if you need to clean the lamp with wet cloth.
Check your electrical connection regularly.
● Opening the luminaire will void warranty.
WARRANTY
Nanolux Technology warrants the mechanical and electronic components of
this product to be free of defects in material and workmanship if used under
normal operating conditions for a period of three (3) years from the original
date of purchase. If the product shows any defects within this period and that
defect is not due to user error or improper use, Nanolux Technology shall, at
its discretion, either replace or repair the product using suitably new or
refurbished parts.
(1) year from the original date of purchase.
the entire product, this limited warranty shall apply to the replacement
ballast for the remaining initial warranty period, i.e. three (3) years from the
date of purchase of the original product. For service return the ballast to your
shop with the original sales receipt.
For more information about Nanolux product please visit nanoluxtech.com
For Nanolux lamp and reflector the warranty period is one
In case Nanolux decides to replace
OPERATING
MANUAL
BALLAST
DE-OG1000-SUMMIT
DOUBLE ENDED FIXTURE
NCCS-RTU/0-10V COMPATIBLE
w w w . n a n o l u x t e c h . c o m
Illuminating Your Grow