Download  Print this page

GE DCVH680GJWW Installation Instructions Manual

Gas dryer
Hide thumbs

Advertisement

I
I
E ESTALS FOR RYERS
T
SBS
0 H SBS
H SBS 22 F

BEFORE YOU BEGIN

R
IM ORTANT
IM ORTANT
N
I
N
C
TOOLS YOU WILL NEED
(x2)
10" ADJUSTABLE WRENCHES
8" PIPE WRENCH
WARNING
California Safe Drinking Water and Toxic Enforcement Act
T
W
A
SLIP JOINT PLIERS
LEVEL
FLAT BLADE SCREWDRIVER
G
I
C
00 GE CARES US
RISK OF FIRE
IN THE COMMONWEALTH OF MASSACHUSETTS
MATERIALS YOU WILL NEED
4" DIA. METAL DUCT
4" DIA. METAL
(RECOMMENDED)
4" DIA. FLEXIBLE METAL (SEMI-RIGID)
UL LISTED TRANSITION DUCT
(IF NEEDED)
CLAMPS (2)
KIT WX08X10077 (INCLUDES 2 ELBOWS)
CLAMPS (2)
4" DIA. FLEXIBLE METAL (FOIL TYPE)
UL LISTED TRANSITION DUCT
(IF NEEDED.)
02
00
www.GEAppliances.com (US)
T
PIPE
EXHAUST
COMPOUND
ELBOW
HOOD
4" DUCT
DUCT TAPE
OR
4" SPRING
FLEXIBLE GAS LINE CONNECTOR
234D1582P002 31-16681 03-12 GE
C
SOAP SOLUTION
FOR LEAK DETECTION
SAFETY
GLASSES
GLOVES

Advertisement

Table of Contents
loading

  Related Manuals for GE DCVH680GJWW

  Summary of Contents for GE DCVH680GJWW

  • Page 1: Before You Begin

    UL LISTED TRANSITION DUCT (IF NEEDED) KIT WX08X10077 (INCLUDES 2 ELBOWS) SLIP JOINT PLIERS 4" DIA. FLEXIBLE METAL (FOIL TYPE) UL LISTED TRANSITION DUCT (IF NEEDED.) 00 GE CARES US www.GEAppliances.com (US) MATERIALS YOU WILL NEED PIPE 4" DIA. METAL EXHAUST COMPOUND...
  • Page 2: Gas Requirements

    PREPARING FOR INSTALLATION OF NEW RYER TIP I ISCONNECTING GAS TURN GAS DISCONNECT AND DISCARD OLD FLEXIBLE GAS CONNECTOR AND SHUT-OFF OLD DUCTING MATERIAL. VALVE TO THE REPLACE WITH NEW CSA(AGA) OFF POSITION. APPROVED FLEXIBLE GAS LINE CONNECTOR AND UL APPROVED TRANSITION DUCT.
  • Page 3 RECONNECTING GAS Listed connector ANSI Z21.24 / CSA 6.10 FLARE NEW METAL FLEXIBLE GAS LINE CONNECTOR ADAPTER 3/8" NPT ELBOW ITEMS NOT SUPPLIED CAUTION APPLY PIPE COMPOUND TO THE ADAPTER AND DRYER GAS INLET. Tighten the flexible gas line using two adjustable wrenches.
  • Page 4: Electrical Requirements

    ELECTRICAL CONNECTION INFORMATION WARNING TO RE UCE THE RISK OF FIRE ELECTRICAL SHOCK AN PERSONAL IN URY O NOT USE AN E TENSION COR OR AN A APTER PLUG WITH THIS APPLIANCE ELECTRICAL REQUIREMENTS WARNING THIS RYER IS EQUIPPE WITH A THREE PRONG GROUN ING PLUG FOR YOUR PROTECTION AGAINST SHOCK HA AR AN SHOUL BE PLUGGE...
  • Page 5 SEALING OF OINTS INSULATION E HAUST CONNECTION BEFORE PERFORMING THIS E HAUST INSTALLATION BE SURE TO ISCONNECT THE RYER FROM ITS ELECTRICAL SUPPLY WARNING TO RE UCE THE RISK OF FIRE OR PERSONAL IN URY THIS RYER COMES REA Y FOR REAR E HAUSTING IF SPACE IS LIMITE USE THE INSTRUCTIONS IN STEP E HAUST IRECTLY FROM THE SI E OR...
  • Page 6 UL LISTE FLE IBLE METAL SEMI RIGI UL LISTE FLE IBLE METAL FOIL TYPE TRANSITION UCT TRANSITION UCT LE ELING RYER Stand the dryer upright near the final location and adjust the 4 leveling legs, at the corners, to ensure that the dryer LEVEL FRONT-TO-BACK 4 LEVELING...
  • Page 7 MOBILE OR MANUFACTURE HOME INSTALLATION GARAGE INSTALLATION IF ALLOWE BY LOCAL CO ES RYER E HAUST TO LEFT OR BOTTOM WARNING BEFORE PERFORMING THIS E HAUST INSTALLATION BE SURE TO ISCONNECT THE RYER FROM ITS ELECTRICAL SUPPLY PROTECT YOUR HAN S AN ARMS FROM SHARP E GES WHEN WORKING INSI E THE CABINET BE SURE TO WEAR GLO ES REMOVE...
  • Page 8 ING ELBOW FOR E HAUST THROUGH BOTTOM OF CABINET CAUTION DUCT TAPE CAUTION: Internal duct joints must be secured with tape, otherwise they may separate and cause a safety hazard. ING CO ER PLATE TO REAR OF CABINET SI ES AN BOTTOM E HAUST PL ATE (KIT WE1M454)
  • Page 9: Before You Start

    BEFORE YOU START REMO E OOR ASSEMBLY Remove the four screws. NOTE 2 #8 Machine Screws 6 #10 Large Screws 2 #8 Machine Screws...
  • Page 10 REMO E HINGE REINSTALL HINGE ASSEMBLY IMPORTANT...
  • Page 11 REINSTALL NUTS AN HINGE CO ER REASSEMBLE OOR ASSEMBLY IMPORTANT...
  • Page 12 REINSTALL OOR ASSEMBLY MO E STRIKE BRACKET SER ICING WARNING LABEL ALL WIRES PRIOR TO ISCONNECTING WHEN SER ICING CONTROLS WIRING ERRORS CAN CAUSE IMPROPER AN ANGEROUS OPERATION AFTER SER ICING INSTALLATION www.GEAppliances.com...
  • Page 13 ROUGH IN IMENSIONS 27" 31 1/8" 1 5/8" 41 1/2" 4 1/2" 11 3/4" 27" 30 5/8" 40 1/4" 39 1/8" 53 5/8" 17" 13 3/8" 11 3/4"...
  • Page 14 NOTES...
  • Page 15 NOTES...
  • Page 16 NOTES...

This manual is also suitable for:

Gfdn110glww