Table of Contents
Advertisement
Quick Links
Blackstar Amplification Ltd, Beckett House, 14 Billing Road, Northampton, NN1 5AW, UK
For the latest information go to: www.blackstaramps.com
Whilst the information contained herein is correct at the time of publication, due to our policy of constant improvement
1
and development, Blackstar Amplification Ltd reserves the right to alter specifications without prior notice.
Owner's Manual
Designed and Engineered by
Blackstar Amplification UK
2
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Blackstar Amplification AMPED Series
Summary of Contents for Blackstar Amplification AMPED Series
- Page 1 For the latest information go to: www.blackstaramps.com Whilst the information contained herein is correct at the time of publication, due to our policy of constant improvement and development, Blackstar Amplification Ltd reserves the right to alter specifications without prior notice. Designed and Engineered by...
- Page 2 IMPORTANT SAFETY INSTRUCTIONS 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water. 6. Clean only with a dry cloth. 7. Do not block any ventilation openings. 8.
- Page 3 Warning! The U.S. Government´s Occupational Safety and Health Administration (OSHA) has specified the following permissible noise level exposures: Important safety information! READ FOLLOWING INFORMATION CAREFULLY. SAVE Duration Per Day In Hours Sound Level dBA, Slow Response INSTRUCTIONS FOR FUTURE REFERENCE! Follow all warnings and instructions marked on the product! Danger! High internal operating voltages.
- Page 4 TONE. In addition to these traditional guitar amp voices, the Flat voice provides the ability The Dept. 10 AMPED series is packed with innovative, ground-breaking technology to plug your favourite amp modeller or preamp pedal directly into your Amped 1 allowing the sound in your head to be more portable than ever before.
-
Page 5: Front Panel
7. Reverb Footswitch Front Panel The Reverb footswitch toggles the Reverb on and off. The LED will light up when the 1. Voice Reverb is active. This setting is saved when you store a preset. When the Reverb The Voice control changes the preamp voicing. Select a preamp character and is active, holding the Reverb footswitch will activate the ‘Freeze’... -
Page 6: Rear Panel
11. Preset 4. Loop Recall the stored Preset by pressing this footswitch. When you activate the switch, The mono effects loop handles both the send and return with a single socket using the LED above the footswitch will light up and the settings stored in the Preset will a TRS connection. -
Page 7: Side Panel
6. Outputs TIP: To record a stereo Room sound, pan the stereo CabRig left channel 100% left Use the two 9V DC outputs to power your external pedals up to a maximum in the mix and pan the right channel 100% right. combined current of 500mA. - Page 8 1. Cabinet Selection Ring Right channel to mixer Left channel Screen to mixer 3. CabRig Switch Use this to switch between the three CabRig settings currently stored in the pedal. You can customise the three factory patches using the CabRig section of Blackstar’s Architect software.
- Page 9 Room Microphone Character Bright and cutting, with controlled lows. A classic microphone choice for recording guitar cabinets. Use 57 - Dynamic this microphone off-axis for a less sharp, mid-focussed tone. Aggressive and tight. Use this microphone for an up- 421 - Dynamic front sound or off-axis for a more mellow sound.
- Page 10 LOW-CUT: Controls a 2nd order high pass filter LOW: Controls a low shelf filter at 120Hz +/- 10dB LOW MIDS: Controls a peak filter at 400Hz +/- 10dB HIGH MIDS: Controls a peak filter at 1KHz +/- 10dB ...
-
Page 11: Settings Panel
Patches and Presets Settings Panel Click the gear icon to open the settings panel. Device (AMPED 1) Patches These are the patches that are currently loaded on your amplifier, selectable via the CabRig switch. Press the save button and “Save Patch to Device” to save your Audio current CabRig settings to one of your “Device Patches”. -
Page 12: Firmware Upgrade
General Function CC Number Value 127 = On Adjust various Architect settings here. 127 = On Voice Flat 127 = On Bass 0-127 Middle 0-127 Preamp Treble 0-127 Gain 0-127 EL84 127 = On EL34 127 = On Response 127 = On Master Volume 0-127 KT88... -
Page 13: Technical Specifications
Technical Specifications AMPED 1 Power (RMS): 100W Weight (kg): 1.28 Dimensions (mm): 200(W) x 81(H) x 149(D) - Page 14 AMPED 1 Top View AMPED 1 Rear View G A I N G A I N G A I N G A I N G A I N G A I N B A S S B A S S B A S S B A S S B A S S...
Need help?
Do you have a question about the AMPED Series and is the answer not in the manual?
Questions and answers