Advertisement
DX Macro Port 52
30111
Thank you for your purchasing SEA&SEA products. Please read this instruction
manual carefully prior to using this product. Only with a thorough understanding of
this manual's content will you be able to use the housing. After reading the manual,
please be sure to keep it in a place where you can easily come back to it at any time.
Note:
The appearance of color evenness or weld lines on the external body of the product is
normal and will not affect its performance.
Safety Precautions
Failure to heed the precautions listed below could result in serious consequences.
To prevent injury or damage to yourself and/or others, please observe the precau-
tions as they contain highly important information related to personal and product
safety.
CAUTION
Situations that could result in property damage or personal
injury.
CAUTION
Unauthorized disassembling and/or modification could result in malfunction or flooding,
and void product warranty. Take the product to a SEA&SEA authorized service center
for repair or inspection.
Do not open the product in a wet or sandy environment. Protect the interior from moisture
and debris in order to prevent malfunction or flooding.
Avoid strong shocks/impacts or excess stress to prevent malfunction, damage or
breakdown. Make sure that the product has been securely mounted to other products
in order to prevent injury, fall or missing.
Do not carry the camera or housing by holding the accessories such as arm, cable,
strobe, etc. Heavy components may fall and cause damage or injury.
Do not leave the product in places with hot temperatures such as inside of a car or in a
car trunk in summer.
Do not store the product in wet or high humidity place, to avoid mold, rust, corrosion or
malfunction.
Do not store the product wet. Thoroughly dry the surface using a soft non-scratching
cloth to prevent spot marks.
SEA&SEA SUNPAK Co., Ltd. will not be responsible for the replacement or compen-
sation for cameras, lenses or those accessories damaged due to your invalid operation.
SEA&SEA SUNPAK Co., Ltd. assumes no liability for compensation of loss of captured
images or expenses caused by loss of images, even if you are unable to shoot due to
a product defect or malfunction.
SEA&SEA SUNPAK Co., Ltd. assumes no liability for errors or discrepancies in this manual.
Precautions on Handling the O-ring
This product is kept watertight by the O-ring. To keep the O-ring functioning properly,
please observe the following. Improper handling of the O-ring could cause flooding.
CAUTION
SEA&SEA products use blue O-rings. These O-rings are impregnated with silicone oil
through a special process. The lubricating effect of the O-ring lasts as long as the
silicone oil is gradually seeping out from within.
For the maintenance of these blue O-rings, make sure to use genuine SEA&SEA
silicone grease (O-ring grease for use with the blue O-rings that comes in tubes with
blue lettering and blue caps). If you use silicone grease from other companies or
SEA&SEA's own silicone grease that comes in tubes with black lettering and black
caps, the grease you apply will be sucked into the blue O-rings due to their special
characteristics, which will result in insufficient grease. If this happens even once, the
O-ring will not revert to its normal state and must be replaced.
If the grease is insufficient, the O-ring will not slide, and it will become harder to open
and close the waterproof parts. Because of this, it could become impossible to open or
close the housing or it could cause flooding, so please refrain from using the housing
with insufficient grease.
Maintenance and Storage
Never use chemicals, cosmetics, any petroleum solvents such as paint thinner, or
neutral detergent on the product. They may deform and damage the product.
After each use in salt water, make sure it's watertight, then soak it sufficiently in fresh
water.
Insufficient soaking causes damage by salt to the product. Salty residue may be left on
the product where it will crystallize as it evaporates. Crystallized salt is hard to dissolve
and difficult to be removed once formed, and it will result in water leakage.
After rinsing, dry the product well with a soft dry cloth, then let the product dry in the
shade, out of direct sunlight.
Do not dry the product by heating (using a hair dryer, for example). Heating can deform
and damage the product.
If you will not use the product for an extended period of time, store it away from high
temperatures, high humidity, direct sunlight, or extreme cold.
Do not store the product with naphthalene or camphor mothballs, or in locations such
as a laboratory where chemicals are used. This environment can cause mold, rust,
corrosion or malfunction.
After using the product, maintain the O-rings before storing. Examine the O-rings before
and after each dive. We recommend early exchange of the O-rings, at least once a year.
Although it depends on how often it is used and how it is stored, an O-ring generally
lasts for one year. Replace the O-ring every year for the best performance of the
product.
Every two years we recommend a complete overhaul of O-rings regardless of the
frequency in use, for the best performance of the product.
Instruction Manual
1017-Z-01B
Identification of Parts
Front glass
* M67→M62 Step Down Ring can be screwed in
the front.
Preparation for Installation
Maintaining the O-ring
This product is kept watertight by the O-ring. To keep the O-ring functioning properly,
please observe the following before setting up.
Make sure to remove the O-ring when maintaining.
For detailed O-ring maintenance methods, please
see the O-ring maintenance manual.
The O-ring is a consumable item, and it generally
lasts for one year. It is advisable to replace it early.
Attaching and Detaching the Port
Attaching
1
Make sure to remove the housing body cap
when attaching the port.
Please refer to the instruction manual of the
housing
2
Pull the port lock on the underside of the
quick shoe base toward OPEN until you
hear the sound of it clicking into place
3
Align the positioning mark on the front case
with the OPEN mark on the port, insert the
port into the front case, and then rotate the
port in a clockwise direction until it stops
CAUTION
Before attaching the port, make sure there are no
specks of dust, scratches, or deformities on the
O-ring and the O-ring contact surfaces.
4
Make sure that the positioning mark on the
front case and the LOCK mark on the port
are aligned
5
Push the port lock toward LOCK until you
hear the sound of it clicking into place
Make sure that the port lock pin is engaged with the
notch in the port.
Position guide mark
Port lock pin
Detaching
1
Set the port lock to the OPEN position
2
Hold the front case firmly and rotate the port in a counterclockwise direction
CAUTION
Do not attempt to remove the port with the port lock in the LOCK position. Doing so
could damage the quick shoe base.
Specifications
Construction Corrosion-resistant aluminium alloy
Depth rating 100m (333feet)
Weight
Dimensions
Accessories Instruction Manual
* Specifications and appearance are subject to change without notice.
http://www.seaandsea.jp
LOCK mark
OPEN mark
φ67mm
Approx. 360g (12.7oz)
Approx. ϕ132(DIA)×62.5(D)mm / 5.28×2.5inches
Front diameter (filter size) φ67mm
SEA&SEA SUNPAK Co., Ltd.
1-4-6, Kitasenzoku, Ohta-ku, Tokyo, Japan 145-0062
TEL. +81-3-5701-5533
World Customer Service Center
Position guide mark
O-ring
OPEN
LOCK
Positioning mark
OPEN mark
Port lock pin
OPEN
LOCK
TEL. +81-48-255-8512
(Current as of Oct.2015)
Advertisement
