Advertisement
Available languages
Available languages
OPERATING INSTRUCTIONS
CPS-1500 MINI AUTOMOBILE
USB POWER SUPPLY
ITEM NO.: 51 83 88
INTENDED USE
This product is designed for charging or operating USB devices. The mini
automobile USB power supply should only be used on car sockets of 12 V/DC.
Only operate the units in dry indoors environment.
For safety and approval purposes (CE), you must not rebuild and/or modify this
product. If you use the product for purposes other than those described above,
the product may be damaged. In addition, improper use can cause hazards
such as short circuiting, fire, electric shock etc. Read the instructions carefully
and keep them. Make this product available to third parties only together with its
operating instructions.
DELIVERY CONTENT
• Mini automobile USB power supply
• Operating instructions
SAFETY INSTRUCTIONS
Read the operating instructions carefully and especially observe
the safety information. If you do not follow the safety instructions
and information on proper handling in this manual, we assume no
liability for any resulting personal injury or damage to property.
Such cases will invalidate the warranty/guarantee.
a) Persons / Product
• The device is not a toy. Keep it out of the reach of children and pets.
• Do not leave packaging material lying around carelessly. These may
become dangerous playing material for children.
• Protect the product from extreme temperatures, direct sunlight,
strong jolts, high humidity, moisture, flammable gases, vapours and
solvents.
• Do not place the product under any mechanical stress.
• If it is no longer possible to operate the product safely, take it out of
operation and protect it from any accidental use. Safe operation can
no longer be guaranteed if the product:
- is visibly damaged,
- is no longer working properly,
- has been stored for extended periods in poor ambient conditions or
- has been subjected to any serious transport-related stresses.
• Please handle the product carefully. Jolts, impacts or a fall even from
a low height can damage the product.
• Also observe the safety and operating instructions of any other devices
which are connected to the product.
b) Miscellaneous
• Consult an expert when in doubt about operation, safety or connection
of the device.
• Maintenance, modifications and repairs are to be performed exclusively
by an expert or at a qualified shop.
If you are not sure about the correct connection or use, or if questions arise
which are not covered by these operating instructions, please do not hesitate to
contact our technical support or another qualified specialist.
Voltcraft®, Lindenweg 15, D-92242 Hirschau, Tel. +49 180/586 582 7.
OPERATION
Always turn off the electrical load before pluging/unpluging the
USB load to the mini automobile USB power supply. Ensure
connection is proper. If the mini automobile USB power supply
is connected improperly, it may heat up or may cause electric
shocks, fire, etc.
VERSION 04/12
The total consumption of the USB device connected to the mini automobile
USB power supply must not be higher than 1.5 A.
1. Insert the mini automobile USB power supply into a car socket of 12 V/DC.
2. The centre pin of the mini automobile USB power supply is the positive
terminal, "+", and the two side clamps are the negative terminals, "–".
3. Connect a USB device to the charger.
4. Check your USB device for the charging / operating status. Disconnect your
USB devices when charging is completed.
You can operate the car plug with the engine running or switched off.
However, do not start the engine while the car plug is in operation, since
the power supply to the cigarette lighter outlet is interrupted during ignition.
When operating the car plug at a high load for a long time, it is advisable to
start the engine in order to recharge the vehicle battery.
The LED indicates that power is connected.
DISPOSAL
Electronic devices are recyclable waste and must not be disposed of in
the household waste.
At the end of its service life, dispose of the product according to the
relevant statutory regulations.
TECHNICAL DATA
Input voltage .................... 12 V/DC
Output voltage ................. 5 V/DC
Output current .................. max. 1.5 A
Operating temperature .... -15 to +60 ºC
Operating humidity .......... 35 – 85 %RH
Storage temperature ........ -25 to +70 ºC
Storage humidity .............. 5 – 95 %RH
Dimensions (ø x L) .......... 28 mm x 48 mm
Weight ............................. 12 g
Legal notice
These operating instructions are a publication by Voltcraft®, Lindenweg 15, D-92242 Hirschau/Germany,
Phone +49 180/586 582 7
(www.voltcraft.de).
All rights including translation reserved. Reproduction by any method, e.g. photocopy, microfilming,
or the capture in electronic data processing systems require the prior written approval by the editor.
Reprinting, also in part, is prohibited.
These operating instructions represent the technical status at the time of printing. Changes in technology
and equipment reserved.
© Copyright 2012 by Voltcraft®
Advertisement
