Letscom Smart Watch ID205L Manual

Getting Started

What's in the box

Smart watch (ID205L with bands)

Charging cable

User manual

What's in this document

This manual gets you started quickly with setting up your watch. Setup ensures that your watch can synchronize its data with the VeryFitPro app, where you can get detailed information on your stats, view historical trends, log sleep, and more. As soon as setup is complete, you're ready to start moving. The remainder of the manual walks you through every function on your ID205L.

Setting up Your Watch

Charging your watch

Please fully charge your watch before initial use.

1. Insert the USB plug of the charging cable into the USB port on your computer or a UL-certified USB wall charger.
2. Hold the other end of the charging cable near the port on the back of the watch until it attaches magnetically.
3. Make sure the pins on the charging cable lock securely with the port. The connection is secure when the watch vibrates and the battery icon with percent charged appears on the screen.

When the watch shows that the battery is low, connect the watch to a USB port with 5V-500mA.

While the watch charges, there is a battery progress bar on the screen and you can press the function button to check the battery level.

Remove the watch from the power supply once fully charged.

• USB charger requirement: DC USB port (5V-500mA)
• Charging time: 2-3 hours

Disassembling / Assembling Your Watch

Disassembly

1. To remove the wristbands, turn over the watch and find the quick-release lever.
2. While pressing the quick-release lever inward, gently pull the wristband away from the watch to release it.
   
3. Repeat on the other side.
   

Assembly

1. To reattach the wristbands, slide the pin (the side opposite the quick-release lever) into the notch on the watch. Attach the wristband with the clasp to the top of the watch.
   

2. While pressing the quick-release lever inward, slide the other end of the wristband into place.
   

3. When both ends of the pin are inserted, release the quick-release lever.

Wearing Your Watch

All-day wear and exercise

For all-day wear when you're not exercising, wear the device on your wrist horizontally, a finger's width below your wrist bone and lying flat, the same way you would put on a watch.

For optimized heart rate tracking, keep these tips in mind:

1. Experiment with wearing the watch higher on your wrist during exercise. Because the blood flow in your arm increases the farther up you go, moving the watch up a couple of inches can improve the heart rate signal. Also, many exercises such as bike riding or weight lifting require you to bend your wrist frequently, which is more likely to interfere with the heart rate signal if the watch is lower on your wrist.
   

2. Do not wear your watch too tight. A tight band restricts blood flow, potentially affecting the heart rate signal. This being said, the watch should also be slightly tighter (snug but not constricting) during exercise than during all-day wear.

Using Your Watch

App Installation

Use the watch with our customized VeryFitPro app. You can download VeryFitPro from Apple Store/Google Play or scan the QR codes below to download.

IOS

Android

Notes:

• The VeryFitPro app is only compatible with smartphones, not tablets or PCs.
• Smartphone operating system should be iOS 8.0 / Android 4.4 or higher; Bluetooth version should be 4.0 or higher.

Smart Phone System Requirements

• iOS 8.0 & higher
• Android 4.4 & higher
• Bluetooth 4.0 & higher

App Interfaces

Mainpage (Swipe down the page to sync data from the watch to your phone)

Details

Device

User

Pairing the Watch with Your Phone

Please pair the watch with your phone in the VeryFitPro app, NOT in the Bluetooth settings of your phone.

Pair the watch with your smartphone in the VeryFitPro app

IOS

Android

Do NOT pair the watch with your smartphone in your phone's Bluetooth settings

1. Enable the Bluetooth of your smartphone.
   
2. Open the VeryFitPro app on your smartphone and go to the "Device" page, tap "Bind Device", then your smartphone starts searching devices
   
3. In the list of found devices that appear on your smartphone, tap on "ID205L" to connect the watch to your smartphone. (If your phone failed to find ID205L, please search the watch on your smartphone again.)
   

Notes:

• Once the watch is connected to your app, the watch will automatically search and reconnect itself if the connection is lost or when Bluetooth is restarted after manual disconnection.
• If the watch is unbound from the app, the information on the watch will be reset, and the information on the app will be cleared. Please do not unbind the connection unless there is an issue that will require a reset.
• The watch can only pair with one smartphone at a time. When pairing, please ensure the watch and your smartphone is within 0.5 meters distance.

Getting to Know Your Watch

Function Button

• Press the function button to wake the screen or return to the previous interface.
• Press and hold the function button to turn on the watch.

Watch Interfaces

This is a touch screen; swipe the screen to go to different interfaces, and tap to enter the function.

Videos

Pairing ID205L Smart Watch Video

Documents / Resources

Download manual

Here you can download full pdf version of manual, it may contain additional safety instructions, warranty information, FCC rules, etc.

Download Letscom Smart Watch ID205L Manual