Philips 40PFL4609/F7 Service Manual
  1. Manuals
  2. Brands
  3. Philips Manuals
  4. LCD TV
  5. 40PFL4609/F7
  6. Service manual

Philips 40PFL4609/F7 Service Manual

40” lcd tv chassis pl14.16
Hide thumbs Also See for 40PFL4609/F7:
Table of Contents

Advertisement

Quick Links

Download this manual
Service Manual
TYPE A
40PFL4609/F7
40PFL4909/F7
40PFL4909/F8
TYPE B
40PFL4709/F7
This service manual contains information of different types of models.
Make sure to refer to the section describing your model.
© 2014 Funai Electric Co., Ltd.
All rights reserved. No part of this manual may be reproduced, copied, transmitted, disseminated, transcribed,
downloaded or stored in any storage medium, in any form or for any purpose without the express prior written
consent of Funai. Furthermore, any unauthorized commercial distribution of this manual or any revision hereto
is strictly prohibited.
Information in this document is subject to change without notice. Funai reserves the right to change the content
herein without the obligation to notify any person or organization of such changes.
with the
without the express written consent of Funai. All other trademarks used herein remain the exclusive property of
their respective owners. Nothing contained in this manual should be construed as granting, by implication or
otherwise, any license or right to use any of the trademarks displayed herein. Misuse of any trademarks or any
other content in this manual is strictly prohibited. Funai shall aggressively enforce its intellectual property rights
to the fullest extent of the law.
PHILIPS
(Serial No.: ME1)
PHILIPS
(Serial No.: ME1)
PHILIPS
(Serial No.: XA1)
PHILIPS
(Serial No.: ME1)
design is a registered trademark of Funai Electric Co., Ltd and may not be used in any way
chassis PL14.16
Contents
40" LCD TV
140327

Advertisement

Table of Contents
loading

Related Manuals for Philips 40PFL4609/F7

Summary of Contents for Philips 40PFL4609/F7

  • Page 1 40” LCD TV chassis PL14.16 Service Manual Contents TYPE A 40PFL4609/F7 PHILIPS (Serial No.: ME1) 40PFL4909/F7 PHILIPS (Serial No.: ME1) 40PFL4909/F8 PHILIPS (Serial No.: XA1) TYPE B 40PFL4709/F7 PHILIPS (Serial No.: ME1) This service manual contains information of different types of models.
  • Page 2 IMPORTANT SAFETY NOTICE Proper service and repair is important to the safe, reliable operation of all P&F Equipment. The service procedures recommended by P&F and described in this service manual are effective methods of performing service operations. Some of these service special tools should be used when and as recommended.

  • Page 3: Table Of Contents

    TABLE OF CONTENTS Specifications ................1-1 Important Safety Precautions .

  • Page 4: Specifications

    SPECIFICATIONS < TUNER / NTSC > Description Condition Unit Nominal Limit 1. AFT Pull-In Range ±2.3 ±2.1 TV.ch.4 dBµV 2. Synchronizing Sens. CA.ch.31 dBµV CA.ch.87 dBµV < TUNER / ATSC > Description Condition Unit Nominal Limit 1. Received Freq. Range (-28dBm) ±100 ch.4 -76/0...

  • Page 5: Important Safety Precautions

    IMPORTANT SAFETY PRECAUTIONS Prior to shipment from the factory, our products are strictly inspected for recognized product safety and electrical codes of the countries in which they are to be sold. However, in order to maintain such compliance, it is equally important to implement the following precautions when a set is being serviced.
  • Page 6 3. Design Alteration Warning - Do not alter or add 7. Product Safety Notice - Some electrical and to the mechanical or electrical design of this TV mechanical parts have special safety-related receiver. Design alterations and additions, characteristics which are often not evident from including, but not limited to circuit modifications visual inspection, nor can the protection they give and the addition of items such as auxiliary audio...
  • Page 7 Precautions during Servicing A. Parts identified by the # symbol are critical for safety. Replace only with part number specified. B. In addition to safety, other parts and assemblies are specified for conformance with regulations applying to spurious radiation. These must also be replaced only with specified replacements.
  • Page 8 Safety Check after Servicing Examine the area surrounding the repaired location for damage or deterioration. Observe that screws, parts and wires have been returned to original positions. Afterwards, perform the following tests and confirm the specified values in order to verify compliance with safety standards. 1.

  • Page 9: Standard Notes For Servicing

    STANDARD NOTES FOR SERVICING Circuit Board Indications How to Remove / Install Flat Pack-IC 1. The output pin of the 3 pin Regulator ICs is 1. Removal indicated as shown. With Hot-Air Flat Pack-IC Desoldering Machine: Top View 1. Prepare the hot-air flat pack-IC desoldering Bottom View machine, then apply hot air to the Flat Pack-IC Input...
  • Page 10 3. The flat pack-IC on the CBA is affixed with glue, so With Soldering Iron: be careful not to break or damage the foil of each 1. Using desoldering braid, remove the solder from pin or the solder lands under the IC when all pins of the flat pack-IC.
  • Page 11 With Iron Wire: 2. Installation 1. Using desoldering braid, remove the solder from 1. Using desoldering braid, remove the solder from all pins of the flat pack-IC. When you use solder the foil of each pin of the flat pack-IC on the CBA flux which is applied to all pins of the flat pack-IC, so you can install a replacement flat pack-IC more you can remove it easily.
  • Page 12 Instructions for Handling Semi- conductors Electrostatic breakdown of the semi-conductors may occur due to a potential difference caused by electrostatic charge during unpacking or repair work. 1. Ground for Human Body Be sure to wear a grounding band (1 MΩ) that is properly grounded to remove any static electricity that may be charged on the body.

  • Page 13: Cabinet Disassembly Instructions [Type A]

    Cover, Hook ↓ ↓ ↓ ↓ ↓ [1] Stand [1] Stand Base Assembly* Assembly* *1: 40PFL4609/F7 [3] Power Supply [4] Digital Main [2] Rear Cabinet CBA Unit *2: 40PFL4909/F7, 40PFL4909/F8 [8] Function Note: [6] Speaker [5] Stand Bracket CBA Unit (1) Order of steps in procedure.
  • Page 14 Make sure the IR Sensor CBA Unit and Sensor Shield are securely in place when re-assembling. [2] Rear Cabinet (S-2) (S-2) (S-2) (S-3) (S-2) (S-3) Stand Neck [1] Stand Assembly (S-1b) [1] Stand Base (S-1) Assembly 40PFL4609/F7 (S-1a) 40PFL4909/F7, 40PFL4909/F8 Fig. D1 PL14.16-A_DC...
  • Page 15 [4] Digital Main CBA Unit Jack Holder (S-5) [3] Power Supply CBA (S-4) Fig. D2 PL14.16-A_DC...
  • Page 16 [7] Speaker Holder L Hook Sensor Shield (S-6) [9] IR Sensor CBA Unit * (S-6) [8] Function CBA Unit * [6] Speaker [7] Speaker Holder R Function Knob [5] Stand Bracket Knob Frame Hook Fig. D3 : Make sure to read all the precautions on page 4-2 when you disassemble/re-assemble the Function CBA Unit or IR Sensor CBA Unit.
  • Page 17 [10] LCD Panel Assembly * Decoration Plate LED Lens Hook Leading Edge Cover Fig. D4 : Make sure to read all the precautions on page 4-2 when you disassemble/re-assemble the LCD Panel Assembly. PL14.16-A_DC...
  • Page 18 TV Cable Wiring Diagram To LCD Panel To LCD Panel Assembly Assembly To LCD Panel Assembly Power Supply CBA CN1101 CN1201 Digital Main CBA Unit CN3906 CN501 CN3601 Function CN601 CBA Unit CN3801 CN3105 To AC Cord To Speaker CN4051 IR Sensor CBA Unit CN4052 CN4001...

  • Page 19: [Type B]

    [TYPE B] Screw Torque Specification Step/ Fig. Loc. Part Removal Note Ref. Part Tightening Part Name Number Torque Stand SCREW F-PAN BLACK_NI L10 GCHP3120 5.2±0.9lb·in D3 --------------- +P-TITE M3X12.0 Bracket SCREW BIND 3CHROM L23 GBJS3060 4.3±0.9lb·in Speaker D3 ---------------- +S-TITE M3X6.0 Speaker SCREW F-PAN BLACK_NI L28 GCHS3080...
  • Page 20 Important precautions concerning the 2. When you disassemble/re-assemble the Function CBA Unit or the IR Sensor CBA Unit LCD Panel Assembly: • Be careful not to break the hooks. If you pull with too 1. When you disassemble/re-assemble the LCD much force, the hooks may be damaged.
  • Page 21 [4] Digital Main CBA Unit Jack Holder (S-5) [3] Power Supply CBA (S-4) Fig. D2 PL14.16-B_DC...
  • Page 22 [7] Speaker Holder L Hook Sensor Shield (S-6) [9] IR Sensor CBA Unit * (S-6) [8] Function CBA Unit * [6] Speaker [7] Speaker Holder R Function Knob [5] Stand Bracket Knob Frame Hook Fig. D3 : Make sure to read all the precautions on page 4-8 when you disassemble/re-assemble the Function CBA Unit or IR Sensor CBA Unit.
  • Page 23 [10] LCD Panel Assembly * Decoration Plate LED Lens Hook Leading Edge Cover Fig. D4 : Make sure to read all the precautions on page 4-8 when you disassemble/re-assemble the LCD Panel Assembly. 4-11 PL14.16-B_DC...
  • Page 24 TV Cable Wiring Diagram To LCD Panel To LCD Panel Assembly Assembly Power Supply CBA To LCD Panel CN1101 Assembly CN1201 Digital Main CBA Unit CN501 CN3013 CN3602 Function CN601 CBA Unit CN3801 CN3101 To AC Cord To Speaker CN4051 IR Sensor CBA Unit CN4052 CN4001...

  • Page 25: Electrical Adjustment Instructions [Type A]

    ELECTRICAL ADJUSTMENT INSTRUCTIONS [TYPE A] 1. Purity Check Mode This mode cycles through full-screen displays of red, General Note: “CBA” is abbreviation for green, blue, and white to check for non-active pixels. “Circuit Board Assembly.” 1. Enter the service mode. Note: Electrical adjustments are required after 2.
  • Page 26 The White Balance Adjustment should be 5. Press [3] button to select the “HDB” for High Drive Blue adjustment. (“HDB” appears in the screen.) performed when replacing the LCD Panel 6. Press [MENU] button. The internal Raster signal or Digital Main CBA. appears in the screen.
  • Page 27 13. Press [9] button to select the “LDB” for Low Drive Blue adjustment (“LDB” appears in the screen.) and press [CHANNEL UP/DOWN] buttons to adjust the color temperature. Internal (Single) 14. Press [7] button to select the “LDR” for Low Drive Red adjustment (“LDR”...

  • Page 28: [Type B]

    [TYPE B] 1. Purity Check Mode This mode cycles through full-screen displays of red, General Note: “CBA” is abbreviation for green, blue, and white to check for non-active pixels. “Circuit Board Assembly.” 1. Enter the service mode. Note: Electrical adjustments are required after 2.
  • Page 29 The White Balance Adjustment should be 6. Press [MENU] button. The internal Raster signal appears in the screen. (“Internal (Single)” appears performed when replacing the LCD Panel in the upper right of the screen as shown below.) or Digital Main CBA. 2.

  • Page 30: How To Initialize The Lcd Tv

    HOW TO INITIALIZE THE LCD TV The purpose of initialization is to place the set in a new out of box condition. The customer will be prompted to select a language and program channels after the set has been initialized. To put the program back at the factory-default, initialize the LCD TV using the following procedure.

  • Page 31: Firmware Renewal Mode [Type A]

    FIRMWARE RENEWAL MODE [TYPE A] Update file selection screen appears as follows. (Files included in the USB storage device are Equipment Required displayed.) a. USB storage device " * " differs depending on the models. b. Remote Control Unit Select an upgrade file *****_******.upg Firmware Update Procedure *****_******.upg...

  • Page 32: [Type B]

    [TYPE B] Equipment Required a. USB storage device b. Remote Control Unit Firmware Update Procedure User Upgrade (Filename example: TVNB2012_00_PH_XX91_FB1.bin) Upgrade the firmware only. The setting values will not be initialized. The User Upgrade and the Firmware Upgrade (Factory Upgrade) will be done by the same file. If you want to upgrade the firmware and initialize the setting values also, add “FACT_”...
  • Page 33 Factory Upgrade (Firmware Upgrade/Flash Upgrade) Firmware Upgrade (Filename example: FACT_TVNB2012_00_PH_XX91_FB1.bin) Upgrade the firmware and initialize the setting values. The User Upgrade and the Firmware Upgrade (Factory Upgrade) will be done by the same file. If you want to upgrade the firmware and initialize the setting values also, add “FACT_” at the beginning of the filename. If you want to upgrade the firmware only and leave the setting values as they are, eliminate the “FACT_”...

  • Page 34: Troubleshooting

    TROUBLESHOOTING Note: This Troubleshooting section covers the entire PL14.16 chassis models. Thus some Reference number of parts shown below may not be used depending on the model. Please refer to the parts list for each model. [Power Supply Section] FLOW CHART NO.1 The power cannot be turned on.
  • Page 35 FLOW CHART NO.5 P-ON+21V is not output. Check D650, D651, D652, D659, C651, C652, C653 C657, C658 and their periphery circuit. Repair it if defective. FLOW CHART NO.6 AMP+13V is not output. FLOW CHART NO.7 [TYPE A] AL+3.3V is not output. PL14.16ATR...
  • Page 36 [Video Signal Section] FLOW CHART NO.1 The key operation is not functioning. Replace the Function CBA Unit. Replace the Digital Main CBA Unit. FLOW CHART NO.2 No operation is possible from the remote control unit. (Operation is possible from the unit.) Check AL+3.3V line and repair it if defective.
  • Page 37 [Audio Signal Section] FLOW CHART NO.1 [TYPE A] Audio is not output normally. See FLOW CHART NO.6 <AMP+13V is not output. [Power Supply Section]> See FLOW CHART NO.7 <AL+3.3V is not output. [Power Supply Section]> Replace the Digital Main CBA Unit. [TYPE B] Audio is not output normally.

  • Page 38: Block Diagrams [Type A]

    BLOCK DIAGRAMS [TYPE A] 1. System Control Block Diagram PL14.16ABLS...
  • Page 39 2. Video/Audio Block Diagram PL14.16ABLVA...
  • Page 40 3. Digital Signal Process Block Diagram PL14.16ABLD...
  • Page 41 4. LED Backlight Drive Block Diagram PL14.16ABLBD...
  • Page 42 5. Power Supply Block Diagram PL14.16ABLP...

  • Page 43: [Type B]

    [TYPE B] 1. System Control Block Diagram PL14.16BBLS...
  • Page 44 2. Video/Audio Block Diagram PL14.16BBLVA...
  • Page 45 3. Digital Signal Process Block Diagram PL14.16BBLD...
  • Page 46 4. LED Backlight Drive Block Diagram PL14.16BBLBD...
  • Page 47 5. Power Supply Block Diagram 9-10 PL14.16BBLP...

  • Page 48: Schematic Diagrams / Cba And Test Points

    SCHEMATIC DIAGRAMS / CBA AND TEST POINTS Standard Notes WARNING Many electrical and mechanical parts in this chassis have special characteristics. These characteristics often pass unnoticed and the protection afforded by them cannot necessarily be obtained by using replacement components rated for higher voltage, wattage, etc.
  • Page 49 LIST OF CAUTION, NOTES, AND SYMBOLS USED IN THE SCHEMATIC DIAGRAMS ON THE FOLLOWING PAGES: 1. CAUTION: CAUTION: FOR CONTINUED PROTECTION AGAINST RISK OF FIRE, REPLACE ONLY WITH SAME TYPE_A,_V FUSE. ATTENTION: UTILISER UN FUSIBLE DE RECHANGE DE MÊME TYPE DE_A,_V. 2.
  • Page 50 Power Supply 1 Schematic Diagram NOTE: CAUTION ! The voltage for parts in hot circuit is measured using CAUTION ! : For continued protection against risk of fire, Fixed voltage (or Auto voltage selectable) power supply circuit is used in this unit. hot GND as a common terminal.
  • Page 51 Power Supply 2 Schematic Diagram JS1101 OPEN CONTINUE POWER 1 POWER SUPPLY CBA AMP+13V L1101 L1103 47uH 47uH P-ON+21V C1101 C1102 C1103 BACKLIGHT-ADJ 330/25V BACKLIGHT-SW D1101 SB2150BD PROTECT3 C1117 C1118 C1114 C1115 C1116 C1120 L1102 L1104 C1119 D1104 R1125 47/100V 47/100V 1/100V 1/100V...
  • Page 52 Digital Main 1 Schematic Diagram [TYPE A] 1 NOTE: The order of pins shown in this diagram is different from that of actual IC3101. IC3101 is divided into seven and shown as IC3101 (1/7) ~ IC3101 (7/7) in this Digital Main Schematic Diagram Section. CONTINUE (NO CONNECTION) CN3905...
  • Page 53 Digital Main 2 Schematic Diagram [TYPE A] CONTINUE DIGITAL 7 P-ON+21V R3942 P-ON+3.3V OPEN CONTINUE R3952 D3905 DIGITAL 2 Q3905 OPEN OPEN OPEN LCD+12V/+21V C3996 OPEN D3906 OPEN IC3901 MP1472GJC452Z R3899 R3550 OPEN 6.8K (+12V REG.) C3946 0.047 R3897 C3949 OPEN R3891 TO LCD PANEL...
  • Page 54 Digital Main 3 Schematic Diagram [TYPE A] 1 NOTE: The order of pins shown in this diagram is different from that of actual IC3101. IC3101 is divided into seven and shown as IC3101 (1/7) ~ IC3101 (7/7) in this Digital Main Schematic Diagram Section. IC3101(2/7) MN2WS0270HA DIGITAL MAIN CBA UNIT...
  • Page 55 Digital Main 4 Schematic Diagram [TYPE A] 1 NOTE: The order of pins shown in this diagram is different from that of actual IC3101. IC3101 is divided into seven and shown as IC3101 (1/7) ~ IC3101 (7/7) in this Digital Main Schematic Diagram Section. IC3101(3/7) MN2WS0270HA DIGITAL SIGNAL PROCESS...
  • Page 56 Digital Main 5 Schematic Diagram [TYPE A] 1 NOTE: The order of pins shown in this diagram is different from that of actual IC3101. IC3101 is divided into seven and shown as IC3101 (1/7) ~ IC3101 (7/7) in this Digital Main Schematic Diagram Section. CONTINUE DIGITAL 7 TU3001...
  • Page 57 Digital Main 6 Schematic Diagram [TYPE A] 1 NOTE: The order of pins shown in this diagram is different from that of actual IC3101. IC3101 is divided into seven and shown as IC3101 (1/7) ~ IC3101 (7/7) in this Digital Main Schematic Diagram Section. DIGITAL MAIN CBA UNIT IC3101(5/7) MN2WS0270HA...
  • Page 58 Digital Main 7 Schematic Diagram [TYPE A] 1 NOTE: The order of pins shown in this diagram is different from that of actual IC3101. IC3101 is divided into seven and shown as IC3101 (1/7) ~ IC3101 (7/7) in this Digital Main Schematic Diagram Section. CONTINUE DIGITAL 1 P-ON+21V...
  • Page 59 Digital Main 8 Schematic Diagram [TYPE A] 1 NOTE: The order of pins shown in this diagram is different from that of actual IC3101. IC3101 is divided into seven and shown as IC3101 (1/7) ~ IC3101 (7/7) in this Digital Main Schematic Diagram Section. DIGITAL MAIN CBA UNIT R3144 CONTINUE...
  • Page 60 Digital Main 1 Schematic Diagram [TYPE B] 1 NOTE: The order of pins shown in this diagram is different from that of actual IC3101. IC3101 is divided into four and shown as IC3101 (1/4) ~ IC3101 (4/4) in this Digital Main Schematic Diagram Section. DIGITAL MAIN CBA UNIT CONTINUE DIGITAL 4...
  • Page 61 Digital Main 2 Schematic Diagram [TYPE B] 1 NOTE: The order of pins shown in this diagram is different from that of actual IC3101. IC3101 is divided into four and shown as IC3101 (1/4) ~ IC3101 (4/4) in this Digital Main Schematic Diagram Section. IC3101(2/4) MSD8220LB1-S1 DIGITAL MAIN CBA UNIT...
  • Page 62 Digital Main 3 Schematic Diagram [TYPE B] 1 NOTE: The order of pins shown in this diagram is different from that of actual IC3101. IC3101 is divided into four and shown as IC3101 (1/4) ~ IC3101 (4/4) in this Digital Main Schematic Diagram Section. IC3101(3/4) MSD8220LB1-S1 DIGITAL MAIN CBA UNIT...
  • Page 63 Digital Main 4 Schematic Diagram [TYPE B] 1 NOTE: The order of pins shown in this diagram is different from that of actual IC3101. IC3101 is divided into four and shown as IC3101 (1/4) ~ IC3101 (4/4) in this Digital Main Schematic Diagram Section. IC3602 DIGITAL MAIN CBA UNIT AP1117EG-13...
  • Page 64 Function Schematic Diagram FUNCTION CBA UNIT TO IR SENSOR CBA UNIT CN4051 CN4001 KEY-IN1 C4002 D4001 MM5Z5V6B D4002 OPEN R4006 R4005 R4004 R4003 R4002 R4001 2.2K 2.2K 2.7K 4.7K 8.2K SW4007 SW4006 SW4005 SW4004 SW4003 SW4002 SW4001 POWER SOURCE MENU CH UP DOWN DOWN...
  • Page 65 IR Sensor Schematic Diagram C4054 R4060 R4053 RS4051 OPEN RS-272 (REMOTE SENSOR) D4051 SMLE12WBC7W1HR POWER R4051 R4052 TO DIGITAL MAIN 6.8K CBA UNIT CN3101 R4054 CN4052 or CN3105 1 AL+3.3V 2 P-ON+5V 3 LIGHT C4051 C4056 C4052 1000P 4 LED1 5 REMOTE C4053 C4055...
  • Page 66 Power Supply CBA Top View CAUTION ! Because a hot chassis ground is present in the power supply Fixed voltage (or Auto voltage selectable) power supply circuit is used in this unit. circuit, an isolation transformer must be used when repairing. CAUTION ! : For continued protection against risk of fire, If Main Fuse (F602) is blown , check to see that all components in the power supply...
  • Page 67 Power Supply CBA Bottom View CAUTION ! Because a hot chassis ground is present in the power supply Fixed voltage (or Auto voltage selectable) power supply circuit is used in this unit. circuit, an isolation transformer must be used when repairing. CAUTION ! : For continued protection against risk of fire, If Main Fuse (F602) is blown , check to see that all components in the power supply...

  • Page 68: Wiring Diagrams [Type A]

    WIRING DIAGRAMS [TYPE A] 11-1 PL14.16AWI...

  • Page 69: [Type B]

    [TYPE B] 11-2 PL14.16BWI...

  • Page 70: Exploded Views

    EXPLODED VIEWS [TYPE A] LCD1 CL3906 Digital Main CBA Unit 40PFL4609/F7, 40PFL4909/F7 CL3601 CL3105 IR Sensor CBA Unit A26-1 AC601 Power Supply CBA Function CBA Unit A26-2 CL4051 SP3801 CL3801 SP3802 See Electrical Parts List SBA1 for parts with this mark.
  • Page 71 [TYPE B] LCD1 CL3013 Digital Main CBA Unit CL3602 CL3101 IR Sensor CBA Unit A26-1 AC601 Power Supply CBA Function CBA Unit A26-2 CL4051 SP3801 CL3801 SP3802 See Electrical Parts List for parts with this mark. SBA1 SSK1 SSK1 12-2 PL14.16CEX...
  • Page 72 Packing *1: 40PFL4609/F7 *2: 40PFL4909/F7, 40PFL4709/F7, 40PFL4909/F8 SSK1 SSK1 Packing Tape Tape Packing Tape SBA1 PCB Label Packing Tape 40PFL4909/F8 Packing Tape Some Ref. Numbers are not in sequence. 12-3 PL14.16-A_PEX...

  • Page 73: Parts List

    TYPE A PARTS LIST [40PFL4609/F7 (Serial No.: ME1)] Mechanical Parts PRODUCT SAFETY NOTE: Products marked with a Ref. No. Description Part No. # have special characteristics important to safety. WARNING MESSAGE FLIER A3ATHUT 2EMN00092 Before replacing any of these components, read...
  • Page 74 Electrical Parts PRODUCT SAFETY NOTE: Products marked with a Ref. No. Description Part No. # have special characteristics important to safety. IC4051 O-E DEVICE LIGHT SENSOR BH1603FVC- QP2Z00BH1603 TR /WSOF6 Before replacing any of these components, read carefully the product safety notice in this service POWER SUPPLY CBA manual.
  • Page 75 Ref. No. Description Part No. Ref. No. Description Part No. C1209 CHIP CERAMIC CAP .(1608) B K 1000pF/50V CHD1JK30B102 L1203 COIL POWER INDUCTORS DIP RP1315BNP- LLF4700SF013 470M/47µH C1210 CHIP CERAMIC CAP .(1608) B K 0.22µF/25V CHD1EK30B224 L1204 COIL CHIP BEADS PZ2012D121-2R5T(F) LLF121SSN006 C1212 CHIP CERAMIC CAP .(1608) B K 1µF/25V...
  • Page 76 Ref. No. Description Part No. RES CHIP 1608 1/10W J 100k  R1107 RRXA104HH013 RES CHIP 1608 1/10W J 10k  R1108 RRXA103HH013 RES CHIP 1608 1/10W J 100k  R1109 RRXA104HH013 RES CHIP 1608 1/10W F 36.0k  R1110 RTW3602HH008 RES CHIP 1608 1/10W F 24.0k ...
  • Page 77 Don't degrade the safety of the product through improper servicing. NOTE: Parts that are not assigned part numbers (---------) are not available. Different parts from the original model 40PFL4609/F7 (Serial No. : ME1) Ref. No. Description Part No. STAND NECK A4DP2UT...
  • Page 78 2. Tolerance of Capacitors and Resistors are noted with the following symbols. C..±0.25% D..±0.5% F..±1% G..±2% J..±5% K..±10% M..±20% N..±30% Z..+80/-20% Different parts from the original model 40PFL4609/F7 (Serial No. : ME1) Ref. No. Description Part No. DIGITAL MAIN CBA UNIT A4DP2MMA-001 2014/02/24 13-6 A4DP2EL.fm...
  • Page 79 Don't degrade the safety of the product through improper servicing. NOTE: Parts that are not assigned part numbers (---------) are not available. Different parts from the original model 40PFL4609/F7 (Serial No. : ME1) Ref. No. Description Part No. REAR CABINET A4GP1UT...
  • Page 80 F..±1% R690 Not used G..±2% J..±5% K..±10% M..±20% N..±30% Z..+80/-20% Different parts from the original model 40PFL4609/F7 (Serial No. : ME1) Ref. No. Description Part No. DIGITAL MAIN CBA UNIT A4GP2MMA-001 CN3701 Not used IC3006 IC 32M-BIT SERIAL FLASH MEMORY...

  • Page 81: Revision History

    REVISION HISTORY Chassis PL14.16 • 2014/02/17 40PFL4609/F7 (Serial No.: ME1) added • 2014/03/27 40PFL4709/F7 (Serial No.: ME1) added • 2014/01/18 40PFL4909/F7 (Serial No.: ME1) First draft added • 2014/03/26 40PFL4909/F8 (Serial No.: XA1) First draft added 14-1 PL14.16REV...
  • Page 82 COMPARISON LIST OF MODEL NAMES Chassis PL14.16 40PFL4609/F7 (ME1) A4DPAUT TYPE A 40PFL4909/F7 (ME1) A4DP2UT TYPE A 40PFL4709/F7 (ME1) A4GP2UT TYPE B 40PFL4909/F8 (XA1) A4DPBMA TYPE A PL14.16COM...

This manual is also suitable for:

40pfl4909/f740pfl4909/f840pfl4709/f7

Table of Contents