Philips 40PFL4901/F7 Service Manual
  1. Manuals
  2. Brands
  3. Philips Manuals
  4. LCD TV
  5. 40PFL4901/F7
  6. Service manual

Philips 40PFL4901/F7 Service Manual

40” lcd tv chassis pl15.01
Hide thumbs Also See for 40PFL4901/F7:
Table of Contents

Advertisement

Quick Links

Service Manual
TYPE A
40PFL4901/F7
40PFL4901/F8
40PFL4911/F8
TYPE B
FW40D36F
This service manual contains information of different types of models.
Make sure to refer to the section describing your
© 2016 Funai Electric Co., Ltd.
All rights reserved. No part of this manual may be reproduced, copied, transmitted, disseminated, transcribed,
downloaded or stored in any storage medium, in any form or for any purpose without the express prior written
consent of Funai. Furthermore, any unauthorized commercial distribution of this manual or any revision hereto
is strictly prohibited.
Information in this document is subject to change without notice. Funai reserves the right to change the content
herein without the obligation to notify any person or organization of such changes.
with the
without the express written consent of Funai. All other trademarks used herein remain the exclusive property of
their respective owners. Nothing contained in this manual should be construed as granting, by implication or
otherwise, any license or right to use any of the trademarks displayed herein. Misuse of any trademarks or any
other content in this manual is strictly prohibited. Funai shall aggressively enforce its intellectual property rights
to the fullest extent of the law.
PHILIPS
(Serial No.: ME4)
PHILIPS
(Serial No.: XA1)
PHILIPS
(Serial No.: XA1)
SANYO
(Serial No.: ME3)
design is a registered trademark of Funai Electric Co., Ltd and may not be used in any way
chassis PL15.01
Contents
model.This service manual contains
40" LCD TV
160621

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the 40PFL4901/F7 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Philips 40PFL4901/F7

Summary of Contents for Philips 40PFL4901/F7

  • Page 1 40” LCD TV chassis PL15.01 Service Manual Contents TYPE A 40PFL4901/F7 PHILIPS (Serial No.: ME4) 40PFL4901/F8 PHILIPS (Serial No.: XA1) 40PFL4911/F8 PHILIPS (Serial No.: XA1) TYPE B FW40D36F SANYO (Serial No.: ME3) This service manual contains information of different types of models.
  • Page 2 IMPORTANT SAFETY NOTICE Proper service and repair is important to the safe, reliable operation of all P&F Equipment. The service procedures recommended by P&F and described in this service manual are effective methods of performing service operations. Some of these service special tools should be used when and as recommended.

  • Page 3: Table Of Contents

    TABLE OF CONTENTS Specifications ................1-1 Important Safety Precautions .

  • Page 4: Specifications

    SPECIFICATIONS < TUNER / NTSC > Description Condition Unit Nominal Limit 1. AFT Pull-In Range ±2.3 ±2.1 TV.ch.4 dBV 2. Synchronizing Sens. CA.ch.31 dBV CA.ch.87 dBV < TUNER / ATSC > Description Condition Unit Nominal Limit 1. Received Freq. Range (-28dBm) ±100 ch.4 -76/0...

  • Page 5: Important Safety Precautions

    IMPORTANT SAFETY PRECAUTIONS Prior to shipment from the factory, our products are strictly inspected for recognized product safety and electrical codes of the countries in which they are to be sold. However, in order to maintain such compliance, it is equally important to implement the following precautions when a set is being serviced.
  • Page 6 3. Design Alteration Warning - Do not alter or add 7. Product Safety Notice - Some electrical and to the mechanical or electrical design of this TV mechanical parts have special safety-related receiver. Design alterations and additions, characteristics which are often not evident from including, but not limited to circuit modifications visual inspection, nor can the protection they give and the addition of items such as auxiliary audio...
  • Page 7 Precautions during Servicing A. Parts identified by the # symbol are critical for safety. Replace only with part number specified. B. In addition to safety, other parts and assemblies are specified for conformance with regulations applying to spurious radiation. These must also be replaced only with specified replacements.
  • Page 8 Safety Check after Servicing Examine the area surrounding the repaired location for damage or deterioration. Observe that screws, parts and wires have been returned to original positions. Afterwards, perform the following tests and confirm the specified values in order to verify compliance with safety standards. 1.

  • Page 9: Standard Notes For Servicing

    STANDARD NOTES FOR SERVICING Circuit Board Indications How to Remove / Install Flat Pack-IC 1. The output pin of the 3 pin Regulator ICs is 1. Removal indicated as shown. With Hot-Air Flat Pack-IC Desoldering Machine: 1. Prepare the hot-air flat pack-IC desoldering Top View Bottom View machine, then apply hot air to the Flat Pack-IC...
  • Page 10 3. The flat pack-IC on the CBA is affixed with glue, so With Soldering Iron: be careful not to break or damage the foil of each 1. Using desoldering braid, remove the solder from pin or the solder lands under the IC when all pins of the flat pack-IC.
  • Page 11 With Iron Wire: 2. Installation 1. Using desoldering braid, remove the solder from 1. Using desoldering braid, remove the solder from all pins of the flat pack-IC. When you use solder the foil of each pin of the flat pack-IC on the CBA flux which is applied to all pins of the flat pack-IC, so you can install a replacement flat pack-IC more you can remove it easily.
  • Page 12 Instructions for Handling Semi- conductors Electrostatic breakdown of the semi-conductors may occur due to a potential difference caused by electrostatic charge during unpacking or repair work. 1. Ground for Human Body Be sure to wear a grounding band (1 M) that is properly grounded to remove any static electricity that may be charged on the body.

  • Page 13: Cabinet Disassembly Instructions

    CABINET DISASSEMBLY INSTRUCTIONS Screw Torque Specification Step/ Fig. Loc. Part Removal Note Ref. Part Tightening Part Name Number Torque Digital Main SCREW BIND 3CHROM 6(S-7), Earth Spring GBJP3080 CBA Unit +P-TITE M3X8.0 SCREW F-PAN BLACK_NI Stand L28 GCHS3080 5.2±0.9lb·in D3 2(S-8) +S-TITE M3X8.0 Bracket SCREW F-PAN BLACK_NI...
  • Page 14 Important precautions concerning the these hooks are not damaged. Make sure the Function CBA Unit, Function Knob and Knob Frame LCD Panel Assembly: are securely in place when re-assembling. 1. When you disassemble/re-assemble the Rear • The IR Sensor CBA Unit and Sensor Shield are Cabinet Assembly.
  • Page 15 [3] Rear Cabinet Assembly (S-4) (L-1) (L-1) (L-1) (S-4) (L-1) (L-1) (L-1) (S-4) (S-4) (S-3) (L-1) (S-4) (S-3) (S-3) (S-4) (S-3) (S-4) (S-4) (S-3) Fig. D2 : Make sure to read all the precautions on page 4-2 when you disassemble/re-assemble the Rear Cabinet Assembly.
  • Page 16 [7] Rear Cabinet [4] Speaker Speaker Holder [6] Stand Bracket (S-8) (S-6) [4] Speaker (S-6) Speaker Holder (S-8) [6] Stand Bracket (S-7) [5] Digital Main CBA Unit Earth Spring Hook Tape Hook Hook Fig. D3 : When assembling the rear cabinet, make sure to tape the speaker cable (CL3801) in place in order to prevent them from slipping off of the hook.
  • Page 17 [9] LCD Panel Assembly [11] Front Cabinet Decoration Plate* Leading Edge Cover* LED Lens* Sensor Shield* Hook* Hook* [8] Function CBA Unit [10] IR Sensor CBA Unit Function Knob* Hook* Knob Frame* Hook* Fig. D4 : Make sure to read all the precautions on page 4-2 when you disassemble/re-assemble the Function CBA Unit or the IR Sensor CBA Unit.
  • Page 18 3. How to Replace the Front Cabinet Disassembly Method CAUTION Disassembly MUST be performed in a CR (Clean Room). Make sure to perform disassembly operations by following “2.Disassembly Method”, until Fig. D3 beforehand to remove the CBA units, speakers, etc. Note: Turning over the unit requires two workers and a wide flat table.
  • Page 19 Work Prohibitions Lift middle part Cause colour spots (Diffusing (same for upper and sheet overlap) lower side) NG At worst, cell can be broken. Lift 1 corner only NG Cause colour spots (Diffusing sheet overlap) At worst, cell can be broken. Rotate to reverse Cause colour spots (Diffusing direction at left and...
  • Page 20 TV Cable Wiring Diagram [TYPE A] Digital Main CBA Unit CN601 CN3901 CN1101 CN3801 CN3501 Function To LCD Panel To LCD Panel CBA Unit Assembly Assembly To AC Cord To Speaker CN4051 IR Sensor CBA Unit CN4052 CN4001 Fig. W1 PL15.01-A_DC...
  • Page 21 [TYPE B] Digital Main CBA Unit CN601 CN3013 CN1101 CN3801 CN3101 Function To LCD Panel To LCD Panel CBA Unit Assembly Assembly To AC Cord To Speaker CN4051 IR Sensor CBA Unit CN4052 CN4001 Fig. W1 PL15.01-A_DC...

  • Page 22: Electrical Adjustment Instructions [Type A]

    ELECTRICAL ADJUSTMENT INSTRUCTIONS [TYPE A] 1. Purity Check Mode This mode cycles through full-screen displays of red, General Note: “CBA” is abbreviation for green, blue, and white to check for non-active pixels. “Circuit Board Assembly.” 1. Enter the service mode. Note: Electrical adjustments are required after 2.
  • Page 23 5. Press [3] button to select the “HDB” for High Drive The White Balance Adjustment should be Blue adjustment. (“HDB” appears in the screen.) performed when replacing the LCD Panel, 6. Press [MENU] button. The internal Raster signal Digital Main CBA. appears in the screen.
  • Page 24 14. Press [VOLUME DOWN] button to shift to the “Debugging Message” mode. If there is no message under “[WB]” section, this adjustment completes. If “Drive settings are NG. Retry again.” is displayed, repeat above steps from 5. to 13. Then check “Debugging Message”...

  • Page 25: [Type B]

    ELECTRICAL ADJUSTMENT INSTRUCTIONS [TYPE B] 1. Purity Check Mode This mode cycles through full-screen displays of red, General Note: “CBA” is abbreviation for green, blue, and white to check for non-active pixels. “Circuit Board Assembly.” 1. Enter the service mode. Note: Electrical adjustments are required after 2.
  • Page 26 The White Balance Adjustment should be 5. Press [3] button to select the “HDB” for High Drive Blue adjustment. (“HDB” appears in the screen.) performed when replacing the LCD Panel, 6. Press [MENU] button. The internal Raster signal Digital Main CBA. appears in the screen.
  • Page 27 15. Press [VOLUME DOWN] button to shift to the “Debugging Message” mode. If there is no message under “[WB]” section, this adjustment completes. If “Drive settings are NG. Retry again.” is displayed, repeat above steps from 5. to 14. Then check “Debugging Message”...

  • Page 28: How To Initialize The Lcd Tv

    HOW TO INITIALIZE THE LCD TV The purpose of initialization is to place the set in a new out of box condition. The customer will be prompted to select a language and program channels after the set has been initialized. To put the program back at the factory-default, initialize the LCD TV using the following procedure.

  • Page 29: Firmware Renewal Mode [Type A]

    FIRMWARE RENEWAL MODE [TYPE A] Equipment Required a. USB storage device b. Remote Control Unit Firmware Update Procedure User Upgrade (Filename example: PHL-0C0HB_***_*.upg) Upgrade the firmware only. The setting values will not be initialized. Update procedure 1. Plug the AC Cord and turn the power on. 6.
  • Page 30 10. When the firmware update is completed, the following will appear in the screen. " * " differs depending on the models. Software update Software update is successful. Please remove the USB storage device and restart the TV set. Remove the USB storage device from the USB port.

  • Page 31: [Type B]

    [TYPE B] Equipment Required a. USB storage device b. Remote Control Unit Firmware Update Procedure User Upgrade (Filename example: TVNB3xxx_00_3H_XX91_HC10.bin) Upgrade the firmware only. The setting values will not be initialized. The User Upgrade and the Firmware Upgrade (Factory Upgrade) will be done by the same file. If you want to upgrade the firmware and initialize the setting values also, add “FACT_”...
  • Page 32 Factory Upgrade (Firmware Upgrade/Flash Upgrade) Firmware Upgrade (Filename example: FACT_TVNB3xxx_00_3H_XX91_HC10.bin) Upgrade the firmware and initialize the setting values. The User Upgrade and the Firmware Upgrade (Factory Upgrade) will be done by the same file. If you want to upgrade the firmware and initialize the setting values also, add “FACT_” at the beginning of the filename. If you want to upgrade the firmware only and leave the setting values as they are, eliminate the “FACT_”...

  • Page 33: Troubleshooting

    TROUBLESHOOTING [Power Supply Section] [TYPE A] FLOW CHART NO.1 The power cannot be turned on. Is the fuse (F601) normal? See FLOW CHART No.2 <The fuse blows out.> Check if there is any leak or short-circuit on the primary circuit component and repair it if defective. (C612A, D601, D602, D603, D604, D605, D606, D607, D608B, D609, D610, D621, D623, Q601, Is the P-ON+21V line voltage normal?
  • Page 34 FLOW CHART NO.5 P-ON+21V is not output. Check D650A, D652A, D658, C650A,C652, C653, C657, R650 and their periphery circuit. Repair it if defective. FLOW CHART NO.6 AMP+13V is not output. PL15.01ATR...
  • Page 35 [Power Supply Section] [TYPE B] FLOW CHART NO.1 The power cannot be turned on. Is the fuse (F601) normal? See FLOW CHART No.2 <The fuse blows out.> Check if there is any leak or short-circuit on the primary circuit component and repair it if defective. (C612A, D601, D602, D603, D604, D605, D606, D607, D608B, D609, D621, D623, Q601, Q602, Is the P-ON+21V line voltage normal?
  • Page 36 FLOW CHART NO.5 P-ON+21V is not output. Check D650A, D652A, D658, C652, C653, C657, C658 and their periphery circuit. Repair it if defective. FLOW CHART NO.6 AMP+13V is not output. PL15.01ATR...
  • Page 37 [Video Signal Section] FLOW CHART NO.1 The key operation is not functioning. Replace the Function CBA Unit. Replace the Digital Main CBA Unit. FLOW CHART NO.2 No operation is possible from the remote control unit. (Operation is possible from the unit.) Check AL+3.3V line and repair it if defective.
  • Page 38 [Audio Signal Section] FLOW CHART NO.1 Audio is not output normally. See FLOW CHART NO.6 <AMP+13V is not output. [Power Supply Section]> Replace the Digital Main CBA Unit. PL15.01ATR...

  • Page 39: Block Diagrams [Type A]

    BLOCK DIAGRAMS [TYPE A] 1. System Control Block Diagram PL15.01ABLS...
  • Page 40 2. Video/Audio Block Diagram PL15.01ABLVA...
  • Page 41 3. Digital Signal Process Block Diagram PL15.01ABLD...
  • Page 42 4. LED Backlight Drive Block Diagram PL15.01ABLBD...
  • Page 43 5. Power Supply Block Diagram PL15.01ABLP...

  • Page 44: [Type B]

    [TYPE B] 1. System Control Block Diagram PL15.01BBLS...
  • Page 45 2. Video/Audio Block Diagram PL15.01BBLVA...
  • Page 46 3. Digital Signal Process Block Diagram PL15.01BBLD...
  • Page 47 4. LED Backlight Drive Block Diagram PL15.01BBLBD...
  • Page 48 5. Power Supply Block Diagram PL15.01BBLP 9-10...

  • Page 49: Schematic Diagrams / Cba And Test Points

    SCHEMATIC DIAGRAMS / CBA AND TEST POINTS Standard Notes WARNING Many electrical and mechanical parts in this chassis have special characteristics. These characteristics often pass unnoticed and the protection afforded by them cannot necessarily be obtained by using replacement components rated for higher voltage, wattage, etc.
  • Page 50 LIST OF CAUTION, NOTES, AND SYMBOLS USED IN THE SCHEMATIC DIAGRAMS ON THE FOLLOWING PAGES: 1. CAUTION: CAUTION: FOR CONTINUED PROTECTION AGAINST RISK OF FIRE, REPLACE ONLY WITH SAME TYPE_A,_V FUSE. ATTENTION: UTILISER UN FUSIBLE DE RECHANGE DE MÊME TYPE DE_A,_V. 2.
  • Page 51 Digital Main 1 Schematic Diagram [TYPE A] CAUTION ! NOTE: Fixed voltage (or Auto voltage selectable) power supply circuit is used in this unit. The voltage for parts in hot circuit is measured using CAUTION ! : For continued protection against risk of fire, If Main Fuse (F601) is blown , check to see that all components in the power supply hot GND as a common terminal.
  • Page 52 Digital Main 2 Schematic Diagram [TYPE A] L1103 OPEN DIGITAL MAIN CBA UNIT CONTINUE L1101 DIGITAL 1 100uH P-ON+21V C1101 C1102 C1103 AMP+13V(1) 330/25V D1101 SB2150BD C1001 D1104 C1117 C1118 C1114 C1115 C1116 C1120 C1124 D1108 OPEN MM5Z20B R1125 47/63V 47/63V 1/100V 1/100V...
  • Page 53 Digital Main 3 Schematic Diagram [TYPE A] 1 NOTE: The order of pins shown in this diagram is different from that of actual IC3102. IC3102 is divided into five and shown as IC3102 (1/5) ~ IC3102 (5/5) in this Digital Main Schematic Diagram Section. CONTINUE DIGITAL 1 P-ON+21V...
  • Page 54 Digital Main 4 Schematic Diagram [TYPE A] 1 NOTE: The order of pins shown in this diagram is different from that of actual IC3102. IC3102 is divided into five and shown as IC3102 (1/5) ~ IC3102 (5/5) in this Digital Main Schematic Diagram Section. IC3102(2/5) MSD93F0JM4-3-002J DIGITAL MAIN CBA UNIT...
  • Page 55 Digital Main 5 Schematic Diagram [TYPE A] 1 NOTE: The order of pins shown in this diagram is different from that of actual IC3102. IC3102 is divided into five and shown as IC3102 (1/5) ~ IC3102 (5/5) in this Digital Main Schematic Diagram Section. DIGITAL MAIN CBA UNIT IC3102(3/5) MSD93F0JM4-3-002J...
  • Page 56 Digital Main 6 Schematic Diagram [TYPE A] 1 NOTE: The order of pins shown in this diagram is different from that of actual IC3102. IC3102 is divided into five and shown as IC3102 (1/5) ~ IC3102 (5/5) in this Digital Main Schematic Diagram Section. IC3606 DIGITAL MAIN CBA UNIT AP1117E33G-13...
  • Page 57 Digital Main 7 Schematic Diagram [TYPE A] 1 NOTE: The order of pins shown in this diagram is different from that of actual IC3102. IC3102 is divided into five and shown as IC3102 (1/5) ~ IC3102 (5/5) in this Digital Main Schematic Diagram Section. DIGITAL MAIN CBA UNIT CN9001 (NO CONNECTION)
  • Page 58 Digital Main 1 Schematic Diagram [TYPE B] CAUTION ! NOTE: Fixed voltage (or Auto voltage selectable) power supply circuit is used in this unit. The voltage for parts in hot circuit is measured using CAUTION ! : For continued protection against risk of fire, If Main Fuse (F601) is blown , check to see that all components in the power supply hot GND as a common terminal.
  • Page 59 Digital Main 2 Schematic Diagram [TYPE B] L1103 OPEN DIGITAL MAIN CBA UNIT CONTINUE L1101 DIGITAL 1 100uH P-ON+21V C1101 C1102 C1103 AMP+13V(1) 330/25V D1101 SB2150BD C1001 D1104 C1117 C1118 C1114 C1115 C1124 C1120 C1119 OPEN MM5Z20B R1125 47/100V 47/100V 1/100V 1/100V 47/100V...
  • Page 60 Digital Main 3 Schematic Diagram [TYPE B] 1 NOTE: The order of pins shown in this diagram is different from that of actual IC3101. IC3101 is divided into five and shown as IC3101 (1/5) ~ IC3101 (5/5) in this Digital Main Schematic Diagram Section. CONTINUE DIGITAL MAIN CBA UNIT DIGITAL 1...
  • Page 61 Digital Main 4 Schematic Diagram [TYPE B] 1 NOTE: The order of pins shown in this diagram is different from that of actual IC3101. IC3101 is divided into five and shown as IC3101 (1/5) ~ IC3101 (5/5) in this Digital Main Schematic Diagram Section. IC3101(2/5) MSD8220LB1-S1 DIGITAL MAIN CBA UNIT...
  • Page 62 Digital Main 5 Schematic Diagram [TYPE B] 1 NOTE: The order of pins shown in this diagram is different from that of actual IC3101. IC3101 is divided into five and shown as IC3101 (1/5) ~ IC3101 (5/5) in this Digital Main Schematic Diagram Section. DIGITAL MAIN CBA UNIT HDMI- JK3002...
  • Page 63 Digital Main 6 Schematic Diagram [TYPE B] 1 NOTE: The order of pins shown in this diagram is different from that of actual IC3101. IC3101 is divided into five and shown as IC3101 (1/5) ~ IC3101 (5/5) in this Digital Main Schematic Diagram Section. IC3602 DIGITAL MAIN CBA UNIT AP1117EG-13...
  • Page 64 Digital Main 7 Schematic Diagram [TYPE B] 1 NOTE: The order of pins shown in this diagram is different from that of actual IC3101. IC3101 is divided into five and shown as IC3101 (1/5) ~ IC3101 (5/5) in this Digital Main Schematic Diagram Section. DIGITAL MAIN CBA UNIT CN9001 (NO CONNECTION)
  • Page 65 IR Sensor Schematic Diagram C4054 R4060 R4053 RS4051 8.2K RS-272 (REMOTE SENSOR) D4051 SMLE12WBC7W1HR POWER R4051 R4052 TO DIGITAL MAIN 6.8K CBA UNIT CN3101 R4054 CN4052 or CN3501 1 AL+3.3V 2 P-ON+5V 3 LIGHT C4051 C4056 C4052 1000P 4 LED1 5 REMOTE C4053 C4055...
  • Page 66 Function Schematic Diagram FUNCTION CBA UNIT TO IR SENSOR CBA UNIT CN4051 CN4001 KEY-IN1 C4002 D4001 MM5Z5V6B D4002 OPEN R4006 R4005 R4004 R4003 R4002 R4001 2.2K 2.2K 2.7K 4.7K 8.2K SW4007 SW4006 SW4005 SW4004 SW4003 SW4002 SW4001 POWER SOURCE MENU CH UP DOWN DOWN...
  • Page 67 Digital Main CBA Top View [TYPE A] Because a hot chassis ground is present in the power supply CAUTION ! circuit, an isolation transformer must be used when repairing. Fixed voltage (or Auto voltage selectable) power supply circuit is used in this unit. CAUTION ! : For continued protection against risk of fire, Also, in order to have the ability to increase the input slowly,...
  • Page 68 Digital Main CBA Bottom View [TYPE A] Because a hot chassis ground is present in the power supply CAUTION ! circuit, an isolation transformer must be used when repairing. Fixed voltage (or Auto voltage selectable) power supply circuit is used in this unit. CAUTION ! : For continued protection against risk of fire, Also, in order to have the ability to increase the input slowly,...
  • Page 69 Digital Main CBA Top View [TYPE B] Because a hot chassis ground is present in the power supply CAUTION ! circuit, an isolation transformer must be used when repairing. Fixed voltage (or Auto voltage selectable) power supply circuit is used in this unit. CAUTION ! : For continued protection against risk of fire, Also, in order to have the ability to increase the input slowly,...
  • Page 70 Digital Main CBA Bottom View [TYPE B] Because a hot chassis ground is present in the power supply CAUTION ! circuit, an isolation transformer must be used when repairing. Fixed voltage (or Auto voltage selectable) power supply circuit is used in this unit. CAUTION ! : For continued protection against risk of fire, Also, in order to have the ability to increase the input slowly,...

  • Page 71: Wiring Diagram [Type A]

    WIRING DIAGRAM [TYPE A] SP3801 SP3802 SPEAKER SPEAKER L-CH R-CH CL3801 CN3501 CN4052 IR SENSOR CBA UNIT CN3801 CL3101 ANT-IN CN4051 COMPONENT -Y/VIDEO-IN CL4051 COMPONENT -Pb-IN COMPONENT CN4001 -Pr-IN FUNCTION CBA UNIT DIGITAL MAIN CBA UNIT AUDIO(L)-IN AUDIO(R)-IN CN601 AC CORD DIGITAL REAR AUDIO OUT...

  • Page 72: [Type B]

    [TYPE B] SP3801 SP3802 SPEAKER SPEAKER L-CH R-CH CL3801 CN3101 CN4052 IR SENSOR CBA UNIT CN3801 CL3101 ANT-IN CN4051 COMPONENT -Y/VIDEO-IN CL4051 COMPONENT -Pb-IN COMPONENT CN4001 -Pr-IN FUNCTION CBA UNIT AUDIO(L)-IN DIGITAL MAIN CBA UNIT AUDIO(R)-IN CN601 AC CORD DIGITAL REAR AUDIO-OUT (COAXIAL)

  • Page 73: Exploded Views

    EXPLODED VIEWS [TYPE A] LCD1 Digital Main CBA Unit CL3013 40PFL4901/F7 SP3801 CL3801 AC601 Function CBA Unit IR Sensor CBA Unit CL3101 SP3802 CL4051 40PFL4911/F8 See Electrical Parts List for parts with this mark. 40PFL4901/F7, SSK1 SSK1 40PFL4901/F8 12-1 PL15.01-A_CEX...
  • Page 74 [TYPE B] LCD1 Digital Main CBA Unit CL3013 FW40D36F SP3801 CL3801 AC601 Function CBA Unit IR Sensor CBA Unit CL3101 SP3802 CL4051 See Electrical Parts List for parts with this mark. SSK1 SSK1 12-2 PL15.01-B_CEX...
  • Page 75 Packing SSK1 Tape Tape [TYPE A] Packing Tape Fixlon Tape Fixlon Tape Fixlon Tape Packing Tape 40PFL4901/F8, 40PFL4911/F8 Packing Tape Packing Tape Some Ref. Numbers are not in sequence. 12-3 PL15.01PEX...

  • Page 76: Parts List

    TYPE A PARTS LIST [40PFL4901/F7 (Serial No.: ME4)] Mechanical Parts PRODUCT SAFETY NOTE: Products marked with a Ref.No. Description Parts No. # have special characteristics important to safety. PACKING Before replacing any of these components, read CARTON A5D22UT 2EMC00988 carefully the product safety notice in this service...
  • Page 77 Electrical Parts PRODUCT SAFETY NOTE: Products marked with a Ref. No. Description Part No. # have special characteristics important to safety. C1106 CHIP CERAMIC CAP .(1608) B K 0.22µF/25V CHD1EK30B224 Before replacing any of these components, read C1107 CHIP CERAMIC CAP .(1608) B K 0.047µF/50V CHD1JK30B473 carefully the product safety notice in this service C1108...
  • Page 78 Ref. No. Description Part No. Ref. No. Description Part No. RES CHIP 1608 1/10W F 22.0k Ω IC3604 IC DC-DC CONVERTER MP2314GJ-Z TSOT23- NSCA0T09M025 R1101 RTW2202HH008 RES CHIP 1005 1/16W F 9.1k Ω R1102 RTV9101HH004 IC3605 IC DC-DC CONVERTER MP2315GJ-Z TSOT23- NSCA0T09M026 RES CHIP 1005 1/16W F 9.1k Ω...
  • Page 79 Don't degrade the safety of the product through improper servicing. NOTE: Parts that are not assigned part numbers (---------) are not available. Different parts from the original model 40PFL4901/F7 (Serial No. : ME4) Ref. No. Description Part No. A15#...
  • Page 80 C..±0.25% D..±0.5% F..±1% G..±2% J..±5% K..±10% M..±20% N..±30% Z..+80/-20% Different parts from the original model 40PFL4901/F7 (Serial No. : ME4) Ref. No. Description Part No. DIGITAL MAIN CBA UNIT A5D23MMA-001 CN1101 PH CONNECTOR TOP 2P B2B-PH-K-S J3PHC02JG029 (LF)(SN) RES. CARBON FILM J 1/2W J 1.2M Ω...
  • Page 81 TYPE A PARTS LIST [40PFL4911/F8 (Serial No.: XA1)] Mechanical Parts PRODUCT SAFETY NOTE: Products marked with a # have special characteristics important to safety. Before replacing any of these components, read carefully the product safety notice in this service manual. Don't degrade the safety of the product through improper servicing.
  • Page 82 Electrical Parts PRODUCT SAFETY NOTE: Products marked with a # have special characteristics important to safety. Before replacing any of these components, read carefully the product safety notice in this service manual. Don't degrade the safety of the product through improper servicing. NOTES: 1.
  • Page 83 Don't degrade the safety of the product through improper servicing. NOTE: Parts that are not assigned part numbers (---------) are not available. Different parts from the original model 40PFL4901/F7 (Serial No. : ME4) Ref. No. Description Part No. REAR CABINET A5G20UT...
  • Page 84 C..±0.25% D..±0.5% F..±1% G..±2% J..±5% K..±10% M..±20% N..±30% Z..+80/-20% Different parts from the original model 40PFL4901/F7 (Serial No. : ME4) Ref. No. Description Part No. DIGITAL MAIN CBA UNIT A5G29MMA-001 C606 CERAMIC CAP . 220pF/2kV CA3D221PAN04 C608 CHIP CERAMIC CAP .(1608) B K 0.015µF/50V...

  • Page 85: Revision History

    REVISION HISTORY Chassis PL15.01 • 2016/04/13 40PFL4901/F7 (Serial No.: ME4) First draft added • 2016/05/13 FW40D36F (Serial No.: ME3) First draft added • 2016/06/21 40PFL4901/F8 (Serial No.: XA1) First draft added • 2016/06/21 40PFL4911/F8 (Serial No.: XA1) First draft added 14-1 PL15.01REV...
  • Page 86 COMPARISON LIST OF MODEL NAMES Chassis PL15.01 40PFL4901/F7 (ME4) A5D22UT TYPE A 40PFL4901/F8 (XA1) A5D23MA TYPE A 40PFL4911/F8 (XA1) A5D2AMA TYPE A FW40D36F (ME3) A5G29MT TYPE B PL15.01COM...

This manual is also suitable for:

40pfl4901/f840pfl4911/f8Sanyo fw40d36f

Table of Contents