Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Motorline professional MC115
Summary of Contents for Motorline professional MC115
- Page 1 MC115 USER’S AND INSTALLER’S MANUAL V1.0 REV. 08/2022...
-
Page 2: Table Of Contents
00.CONTENT 01. SAFETY INSTRUCTIONS INDEX ATTENTION: 01. SAFETY INSTRUCTIONS This product is certified in accordance with European Community (EC) safety standards. 02. PRODUCT DESCRIPTION OF PRODUCT This product complies with Directive 2011/65/EU of the TECHNICAL CHARACTERISTICS DIMENSIONS European Parliament and of the Council, of 8 June 2011, on COMPONENTS MAP the restriction of the use of certain hazardous substances in electrical and electronic equipment. - Page 3 01. SAFETY INSTRUCTIONS GENERAL WARNINGS the motorized door or gate from being triggered involuntarily. • This manual contains very important safety and usage information. WARNINGS FOR TECHNICIANS very important. Read all instructions carefully before beginning the installation/usage procedures and keep this manual in a safe place •...
- Page 4 01. SAFETY INSTRUCTIONS RESPONSABILITY to the release mechanism. • Disconnect means, such as a switch or circuit breaker on the electrical • Supplier disclaims any liability if: panel, must be provided on the product’s fixed power supply leads in • Product failure or deformation result from improper installation accordance with the installation rules.
-
Page 5: Mr13 Receiver Connections
02. PRODUCT 02. PRODUCT DESCRIPTION OF PRODUCT COMPONENTS MAP • Control board capable of working with motors up to 4000W. It has a frequency inverter that allows a soft The control board is composed of the following components: start and stop, thus providing greater reliability and durability of the product. The control board also 1 ·... - Page 6 03. COMPONENTS 03. COMPONENTS MR13 - RECEIVER MF2020 The MF2020 is a column photocell designed to safeguard all types of industrial doors (sectional and rapid LEARN BUTTON doors) up to a maximum width of 10 meters. The emitter and receiver create a grid of infrared beams offering protection up to 2.5 meters high (depending •...
- Page 7 04. FREQUENCY INVERTERS AND CONECTORS 04. FREQUENCY INVERTERS AND CONECTORS FREQUENCY INVERTERS CONNECTIONS CONNECTIONS CONNECTORS The following panel are all inputs and The below panel ate all inputs and outputs of connection connectors. 24V • Common STOP outputs of frequency inverter. S1 •...
- Page 8 05. CONNECTIONS SQUEME FREQUENCY INVERTER CONNECTIONS FREQUENCY INVERTER SGND Black Black Black Blue...
- Page 9 05. CONNECTIONS SQUEME MR13 RECEIVER CONNECTIONS FREQUENCY INVERTER SGND Black Black Black Blue MR13...
-
Page 10: Other Connections (Magnetic Loop Detector, Resistor And Push Button)
05. CONNECTIONS SQUEME OTHER CONNECTIONS (MAGNETIC LOOP DETECTOR, RESISTOR AND PUSH BUTTON) LOOP1 • LOOP1 for Magnetic Loop LOOP1 • LOOP1 for Magnetic Loop FREQUENCY LOOP2 • LOOP2 for Magnetic Loop INVERTER LOOP2 • LOOP2 for Magnetic Loop SGND Black Black Black Blue... -
Page 11: Closing Pre- Flashing Light
05. CONNECTIONS SQUEME CLOSING PRE- FLASHING LIGHT NO • 24Vdc 3W Negative Output COM • Common FREQUENCY INVERTER SGND To configure flashing light operation, see page 17B. -
Page 12: Ups Unit Connection
05. CONNECTIONS SQUEME UPS UNIT CONNECTION UPS POWER SUPPLY OUTPUT UPS POWER SUPPLY INPUT UPS UNIT COM • Common NC • Relay Contact A1 • Power Supply A2 • Power Supply N (OUT) • Power Supply L (OUT) • Power Supply N (IN) •... -
Page 13: Relay For Two-Door Interlock
05. CONNECTIONS SQUEME RELAY FOR TWO-DOOR INTERLOCK For the two-door Interlock system to work, it is necessary to set parameter 04.61 of When using relay for two-door interlock, it is PROGRAMMING MENU 4 to the value 1 (Interlock). necessary to change the connection indicated for this wire on page 9, to the one indicated here. -
Page 14: External Components Connections
05. CONNECTIONS SQUEME EXTERNAL COMPONENTS CONNECTIONS Blue Black Green Yellow CLOSING OPENING... -
Page 15: Descriptions
06. DESCRIPTIONS 06. DESCRIPTIONS DIGITAL NUMERIC KEYBOARD MENU NAVIGATION Press ENTER to enter the MENU Using the arrows, select one of the SUBMENUS referenced on page 16A. OK Inverter Ascent Motion Press ENTER to enter the SUBMENU. Descent Motion Status Display Shows the current state of the STOP Stand By... -
Page 16: Lock/Unlock Keyboard 15A
06. DESCRIPTIONS 06. DESCRIPTIONS LOCK/UNLOCK KEYBOARD PROGRAMMING MENU ACCESS (MENU 04) Keyboard locking is done through a password. Below are the setps for configuring and using the password. SET PASSWORD Press MODE until you find H function. Enter at parameter 00.08 and set password to lock the keyboard. -
Page 17: Programming Menu
06. DESCRIPTIONS 06. DESCRIPTIONS PROGRAMMING MENU - 04 PROGRAMMING MENU - 04 Parameter Function Settings Factory Setting If the values are incorrectly adjusted, there is a risk of damage to the motor and inverter. PEDESTRIAN OPENING TIME This menu can select the lenght of the pedestrian opening. Knowing 04.57 that 100 means 8M if put 12 means opening of a meter. -
Page 18: Programming
07. PROGRAMMING SLOWDOWN ADJUSTMENT Slowdown is a reduction in the door's movement speed until it reaches the limit switch. To adjust the slowdown at opening and closing the door, follow these steps in the following order: Ensure that the limit switches are adjusted to the movement of the door. - Page 19 07. PROGRAMMING 08. TROUBLESHOOTING LED DISPLAY MESSAGES INSTRUCTIONS FOR CONSUMERS AND SPECIALIZED TECHNICIANS Message Fault identifi- Description Description of failure Corrections displayed cation Displays the master frequency of the AC inverter. 01 • Check if the motor power corresponds to the output power of the AC motor inverter.
Need help?
Do you have a question about the MC115 and is the answer not in the manual?
Questions and answers