Table of Contents
Advertisement
Quick Links
pneumatic roll pushers
MR
100 |
MR
100 S |
MR
200 |
MR
200 S
MR
100 K |
MR
100 SK |
MR
200 K |
MR
200 SK
MR
100 H |
MR
100 SH
|MR
200 H|
MR
200 SH
MR
100 L |
MR
100 SL |
MR
200 L|
MR
200 SL
operating instructions
Renova srl – viale Rimembranze 93 – 20099 Sesto San Giovanni - Italy – tel: +39.02.2700.7394 – fax: +39.02.2570.8635
www.renova-srl.com – email: support@renova-srl.com
Advertisement
Table of Contents
Related Manuals for Renova moniroll MR 100
Summary of Contents for Renova moniroll MR 100
- Page 1 100 SH 200 H| 200 SH 100 L | 100 SL | 200 L| 200 SL operating instructions Renova srl – viale Rimembranze 93 – 20099 Sesto San Giovanni - Italy – tel: +39.02.2700.7394 – fax: +39.02.2570.8635 www.renova-srl.com – email: support@renova-srl.com...
- Page 2 This product complies with the Directive 2006/42/CE © Copyright Renova Srl, 2013. All rights reserved. MANMRENA4V0421...
-
Page 3: Table Of Contents
index introduction ……………………………………………………..…………………….…… page 4 foreword ….………………………………………….……………………….……………… page 4 advices ………………………………………………………………………..…………..…… page 5 mounting and installation ………………………………………….………….……… page 5 initial content ………………………………………………………..………… page 5 assembly …………………………..……………………………….….….….… page 6 use without counter spring …………………………………….……..… page 7 installation ………………………………………………………………….…… page 8 pneumatic line dimensioning …………………..………..……..……… page 8 operating pressure ……….…………..……………………………………. -
Page 4: Introduction
(including but not limited to improper maintenance and storage), accidents, improper installation, modifications (included but not limited to the use of non-original parts or accessories not authorized by Renova), improper adjustment or repair. All parts subject to normal wear are excluded from the guarantee. -
Page 5: Advices
The manufacturer’s instructions must be read and completely understood before the installation and use of the product and, in the case of breakdown, before any check intervention or recourse at the Renova’s technical assistance. The operator must understand the manufacturer’s instructions and be aware of the dangers. ... -
Page 6: Assembly
ASSEMBLY The assembly is made through rapid and simple operations. 1. Initial situation after the removal from the box (fig.1) 2. Insert the supply pipe into the pipe fitting of the motor (fig.2) 3. Place the fastener in its fixing position paying attention to the correct alignment of the handle in relation to the mechanical lock for the rotation (fig.3) 4. -
Page 7: Use Without Counter Spring
fig. 3 fig. 4 fig. 5 USE WITHOUT COUNTER SPRINGS Counter springs are mounted on the device. They allow the rollers to get into contact between them. The springs are designed and calibrated to guarantee the contact between the 3 rollers only when compressed by the roll weight. -
Page 8: Installation
INSTALLATION Below please find some simple steps and devices to better use this quality product. The pneumatic motor air supply is essential for the correct functioning of the moviroll. You need to follow small but essential measures in order to achieve maximum performance without loss of power or machine malfunctions The pneumatic motor on moviroll needs treated compressed, filtered and lubricated air at bar. - Page 9 Connect a pipe with an internal diameter of at least 12 mm and a length depending on the distances need cover. Spiral pipe 15 mt. 12X15 mm pressure rating up to 10 bar. Connect the end of the tube to a pipe-fitting as shown in the picture.
-
Page 10: Operating Pressure
OPERATING PRESSURE moviroll correctly works in a pressure range that goes from 6 to 7 bar. It is important to verify that the input pressure does not drop under 6 bar when running motor. In the case the pressure drops under this value, increase the pressure that supplies the moviroll to obtain a work pressure of about 6 bar continuously. -
Page 11: Use And Maintenance
The non-compliance with the above parameters may cause damage to the internal components of the motor. In this case Renova srl disassociates itself from any responsibility. Any foreign matter that gets into the motor such as dirt, metallic powder or other, may cause a permanent damage and the subsequent seizure of it. The greatest attention must be paid to the methods of air filtering. -
Page 12: Connection Scheme
CONNECTION SCHEME PREASSURE AIR LINE Clean the filter Fill with oil INSTRUCTIONS FOR A PROPER USE moviroll versions MR100S and MR200S with curved handle must be used with the handle in their appropriate locations (see the drawing). Any other position or use of the handle doesn’t guarantee the integrity of the handle itself. -
Page 13: Change Of The Vanes Of The Pneumatic Motor
(improper use of the moviroll as brake). Renova’s moviroll is provided with its original air supply kit (code MVRK001) in order to ensure the maximum performance and durability of moviroll. If supplying moviroll with untreated air, a power reduction of up to 70% is possible and the premature wear of its internal parts may occur. -
Page 14: Exploded View Drawings And Components
EXPLODED VIEWS AND COMPONENTS MR200/MR200S gear motor... - Page 15 Position Description Code Quantity MR100 MR200 MR100S MR200S chassis right side cover MVRP0002 MVRP0033 chassis left side cover MVRP0001 MVRP0032 chassis pull-rod MVRP0021 MVRP0021 spring MVRP0019 MVRP0019 spring support MVRP0020 MVRP0020 rubber roller axis MVRP0015 MVRP0015 assembled rubber roller MVRP0018 MVRP0018 galvanized washer R60-0005...
- Page 16 Position Description Code MR100 MR200 MR100S MR200S air supply kit MVRK001 MVRK001 straight handle kit MVRK002 MVRK002 curved handle kit MVRK003 MVRK003...
- Page 19 NOTES...
- Page 20 Renova srl – viale Rimembranze 93 – 20099 Sesto San Giovanni - Italy – tel: +39.02.2700.7394 – fax: +39.02.2570.8635 www.renova-srl.com – email: support@renova-srl.com...
Need help?
Do you have a question about the moniroll MR 100 and is the answer not in the manual?
Questions and answers