Page 1
Service NR1606 / U1B/N1B/N1SG /K1B/FB Manual AV SURROUND RECEIVER • For purposes of improvement, specifications and design are subject to change without notice. • Please use this service manual with referring to the operating instructions without fail. • Some illustrations using in this service manual are slightly different from the actual set. Ver.
Contents ABOUT THIS MANUAL ..............3 TROUBLE SHOOTING ..............71 What you can do with this manual ...........3 1. POWER ................71 Using Adobe Reader (Windows version) ........4 2. Analog video ..............72 3. HDMI/DVI ................76 SAFETY PRECAUTIONS ...............6 4. AUDIO ................78 NOTE FOR SCHEMATIC DIAGRAM ..........7 5.
ABOUT THIS MANUAL Read the following information before using the service manual. What you can do with this manual Search for a Ref. No. (phrase) Jump to the target of a schematic diagram connector (Ctrl+Shift+F) You can use the search function in Acrobat Reader to search for a Ref.
SAFETY PRECAUTIONS The following items should be checked for continued protection of the customer and the service technician. leakage current check Beforereturningthesettothecustomer,besuretocarryouteither(1)aleakagecurrentcheckor(2)alinetochassis resistance check. If the leakage current exceeds 0.5 milliamps, or if the resistance from chassis to either side of the power cord is less than 460 kohms, the set is defective.
NOTE FOR SCHEMATIC DIAGRAM WARNING: Partsindicatedbythe z markhavecriticalcharacteristics.UseONLYreplacementpartsrecommendedbythemanufacturer. CAUTION: Beforereturningthesettothecustomer,besuretocarryouteither(1)aleakagecurrentcheckor(2)alinetochassisresistancecheck. If the leakage current exceeds 0.5 milliamps, or if the resistance from chassis to either side of the power cord is less than 460 kohms, the set is defective. WARNING: DONOTreturnthesettothecustomerunlesstheproblemisidentifiedandremedied.
TECHNICAL SPECIFICATIONS n Audio section n Wireless LAN section • Power amplifier Network type (wireless LAN standard) : Conforming to IEEE 802.11b Conforming to IEEE 802.11g Rated output : Conforming to IEEE 802.11n Front : (Wi-Fi® compliant)z1 50 W + 50 W ( 8 Ω, 20 Hz - 20 kHz with 0.08 % T.H.D.) Security : WEP 64 bit, WEP 128 bit 70 W + 70 W ( 6 Ω, 1 kHz with 0.7 % T.H.D.)
CAUTION IN SERVICING Initializing This Unit Make sure to initialize this unit after replacing the microcomputer or any peripheral equipment, or the digital PCB. Press the power button to turn off the power. While holding down buttons "ZONE2 SOURCE" and "INTERNET RADIO" simultaneously, press the power button to turn on the power.
DISASSEMBLY • Remove each part following the flow below. • Reassemble the removed parts in the reverse order. Read "Precautions During Work" before reassembling the removed parts. • • If wire bundles are removed or moved during adjustment or part replacement, reshape the wires after completing the work.
Page 13
Explanatory Photos for DISASSEMBLY • For the shooting direction of each photos used in this manual, see the photo below. A, B, C and D in the photo below indicate the shooting directions of photos. • • The photographs with no shooting direction indicated were taken from the top of the unit. •...
1. FRONT PANEL ASSY Proceeding : TOP COVER FRONT PANEL ASSY → (1) Remove the screws. View from the bottom (2) Remove the screws. Remove the CORD HOLDER. Cut the wire clamp, then remove the connector. Remove the FFC. CP4401 CORD HOLDER N1008 2.
5. TRANS Proceeding : TOP COVER HDMI PCB TRANS → → (1) Remove the CORD HOLDERs and connector wires. from CP4401 CP4001 CP4607 CP4142 CORD HOLDERx5 (2) Remove the screws. View from the bottom NOTE : It will separate and TRANS will fall from SET, if screws is removed. 6.
SPECIAL MODE Special mode setting button No. 1 - 6, 9 : While holding down buttons "A", "B" and "C" simultaneously, press the power button to turn on the power. No. 7, 8 : While the power is on, hold down buttons "A" and "B" for at least 3 seconds . No.
1. Version Display Mode 1.1. Actions Version information is displayed when the device is started in this mode. 1.2. Starting up While holding down buttons "DIMMER" and "STATUS" simultaneously, press the power button to turn on the power. then press the "STATUS" button to display the information in section 1.3 on the display. The version list is also displayed on GUI while the version is displayed on the display.
Page 19
i Ethernet 1st Boot Loader, Hardware ID : E t h e r n e t F B L Press "STATUS" button. * * * * * * - b d o Ethernet 2nd Boot Loader, Rhapsody Flag : E t h e r n e t S B L Press "STATUS"...
Page 20
1.4. Error display See the table below for descriptions of the displayed errors and countermeasures for these. If multiple errors occur, only one item is displayed. The priority order is w , e , r , t , y , q . Condition States Display...
Page 21
1.5. Version Display in the Setup Menu Follow the steps below to display the firmware information. (1) Press the "SETUP" button on the remote control. (2) Select "General - Information - Firmware". The version information is displayed as a 12-digit number as shown in the screenshot below. General/Firmware XXXX-XXXX-XXXX Version...
2. PANEL / REMOTE LOCK Selection Mode 2.1. Actions Switch the PANEL LOCK and REMOTE LOCK modes between on and off. 2.2. Starting up While holding down buttons "M-DAX" and "DIMMER" simultaneously, press the power button to turn on the power. Select the desired mode using the "INTERNET RADIO"...
3. Selecting the Mode for Service-related Operations 3.1. Actions Select diagnostic mode (service path check mode), protection history display mode mode. 3.2. Starting up While holding down buttons "ZONE2 SOURCE" and "STATUS" simultaneously, press the power button to turn on the power.
Page 24
3.5. DIAGNOSTIC MODE (Service Path Check Mode) 3.5.1. Actions This function is convenient for confirming problem paths in the product and checking the paths after repairing. The Video and Audio paths can be checked. The backup data is not rewritten. 3.5.2.
Page 25
3.5.5. Confirmation items for the video system See the block diagram fig.XXth. Paths to be confirmed Display Settings What to confirm Analog Video pass Input Source : CBL/SAT ・ Component input ⇒ Component output V 0 1 : V I D E O P A S S Video Convert (IP Scaler) : OFF, All sources ・...
DIAGNOSTIC PATH DIAGRAM fig.01 ANALOG AUDIO DIAGRAM H/P-L HEADPHONE OUT TO DIGITAL AUDIO BLOCK TO DIGITAL AUDIO BLOCK TO DIGITAL AUDIO BLOCK H/P-R SPK OUT SBL(FL-B/FL-H/BI-AMP/ZONE) SBR(FR-B/FR-H/BI-AMP/ZONE) DM920_R/L ANA_FL DSP_FL ANALOG ANA_FR SAT_CBL DSP_FR INPUT 2.2ch PREOUT DSP_C TUNER DSP_SW FM/AM MIC(Mini Jack) DSP_SL DSP_SR DSP_SBL...
Page 28
fig.02b ANALOG AUDIO DIAGRAM H/P-L HEADPHONE OUT TO DIGITAL AUDIO BLOCK TO DIGITAL AUDIO BLOCK TO DIGITAL AUDIO BLOCK H/P-R SPK OUT SBL(FL-B/FL-H/BI-AMP/ZONE) SBR(FR-B/FR-H/BI-AMP/ZONE) DM920_R/L ANA_FL DSP_FL ANALOG ANA_FR SAT_CBL DSP_FR INPUT 2.2ch PREOUT DSP_C TUNER DSP_SW FM/AM MIC(Mini Jack) DSP_SL DSP_SR DSP_SBL...
Page 30
fig.03b ANALOG AUDIO DIAGRAM H/P-L HEADPHONE OUT TO DIGITAL AUDIO BLOCK TO DIGITAL AUDIO BLOCK TO DIGITAL AUDIO BLOCK H/P-R SPK OUT SBL(FL-B/FL-H/BI-AMP/ZONE) SBR(FR-B/FR-H/BI-AMP/ZONE) DM920_R/L ANA_FL DSP_FL ANALOG ANA_FR SAT_CBL INPUT DSP_FR 2.2ch PREOUT DSP_C TUNER DSP_SW FM/AM MIC(Mini Jack) DSP_SL DSP_SR DSP_SBL...
Page 32
fig.04b ANALOG AUDIO DIAGRAM H/P-L HEADPHONE OUT TO DIGITAL AUDIO BLOCK TO DIGITAL AUDIO BLOCK TO DIGITAL AUDIO BLOCK H/P-R SPK OUT SBL(FL-B/FL-H/BI-AMP/ZONE) SBR(FR-B/FR-H/BI-AMP/ZONE) DM920_R/L ANA_FL DSP_FL ANALOG ANA_FR SAT_CBL DSP_FR INPUT 2.2ch PREOUT DSP_C TUNER DSP_SW FM/AM MIC(Mini Jack) DSP_SL DSP_SR DSP_SBL...
Page 34
fig.05b ANALOG AUDIO DIAGRAM H/P-L HEADPHONE OUT TO DIGITAL AUDIO BLOCK TO DIGITAL AUDIO BLOCK TO DIGITAL AUDIO BLOCK H/P-R SPK OUT SBL(FL-B/FL-H/BI-AMP/ZONE) SBR(FR-B/FR-H/BI-AMP/ZONE) DM920_R/L ANA_FL DSP_FL ANALOG ANA_FR SAT_CBL DSP_FR INPUT 2.2ch PREOUT DSP_C TUNER DSP_SW FM/AM MIC(Mini Jack) DSP_SL DSP_SR DSP_SBL...
Page 35
fig.06 ANALOG AUDIO DIAGRAM H/P-L HEADPHONE OUT TO DIGITAL AUDIO BLOCK TO DIGITAL AUDIO BLOCK TO DIGITAL AUDIO BLOCK H/P-R SPK OUT SBL(FL-B/FL-H/BI-AMP/ZONE) SBR(FR-B/FR-H/BI-AMP/ZONE) DM920_R/L ANA_FL DSP_FL ANALOG ANA_FR SAT_CBL INPUT DSP_FR 2.2ch PREOUT DSP_C TUNER DSP_SW FM/AM MIC(Mini Jack) DSP_SL DSP_SR DSP_SBL...
Page 36
VIDEO DIAGRAM fig.07 ADV8195 FRONT HDMI TMDS IN BUFFER OUT0 TMDS OUTPUT HDMI OUT1 TMDS IN HDMI1 HDMI2.0 RX MN864788 HDMI2.0 TX (2.2 4 INPUTS) MN864788 HDMI2 MX25L12835FMI HDMI IN TMDS OUT TMDS IN HDMI3 OUT1 HDMI4 TMDS OUT HDMI5 HDMI RECEIVER OUT0 VIDEO DECODER...
Page 37
VIDEO DIAGRAM fig.08 ADV8195 FRONT HDMI TMDS IN BUFFER OUT0 TMDS OUTPUT HDMI OUT TMDS IN HDMI1 HDMI2.0 RX MN864788 HDMI2.0 TX (2.2 4 INPUTS) MN864788 HDMI2 MX25L12835FMI HDMI IN TMDS OUT TMDS IN HDMI3 OUT1 HDMI4 TMDS OUT HDMI5 OUT0 HDMI RECEIVER VIDEO DECODER...
Page 38
VIDEO DIAGRAM fig.09 ADV8195 FRONT HDMI TMDS IN BUFFER OUT0 TMDS OUTPUT HDMI OUT TMDS IN HDMI1 HDMI2.0 RX MN864788 HDMI2.0 TX (2.2 4 INPUTS) MN864788 HDMI2 MX25L12835FMI HDMI IN TMDS OUT TMDS IN HDMI3 OUT1 HDMI4 TMDS OUT HDMI5 OUT0 HDMI RECEIVER VIDEO DECODER...
Page 39
VIDEO DIAGRAM fig.10 ADV8195 FRONT HDMI TMDS IN BUFFER OUT0 TMDS OUTPUT HDMI OUT1 TMDS IN HDMI1 HDMI2.0 RX MN864788 HDMI2.0 TX (2.2 4 INPUTS) MN864788 HDMI2 MX25L12835FMI HDMI IN TMDS OUT TMDS IN HDMI3 OUT1 HDMI4 TMDS OUT uCOM HDMI5 HDMI RECEIVER OUT0...
Page 41
ANALOG AUDIO DIAGRAM fig.11b H/P-L HEADPHONE OUT TO DIGITAL AUDIO BLOCK TO DIGITAL AUDIO BLOCK TO DIGITAL AUDIO BLOCK H/P-R SPK OUT SBL(FL-B/FL-H/BI-AMP/ZONE) SBR(FR-B/FR-H/BI-AMP/ZONE) DM920_R/L ANA_FL DSP_FL ANALOG ANA_FR SAT_CBL INPUT DSP_FR 2.2ch PREOUT DSP_C TUNER DSP_SW FM/AM MIC(Mini Jack) DSP_SL DSP_SR DSP_SBL...
Page 43
VIDEO DIAGRAM fig.13 ADV8195 FRONT HDMI TMDS IN BUFFER OUT0 TMDS OUTPUT HDMI OUT1 TMDS IN HDMI1 HDMI2.0 RX MN864788 HDMI2.0 TX (2.2 4 INPUTS) MN864788 HDMI2 MX25L12835FMI HDMI IN TMDS OUT TMDS IN HDMI3 OUT1 HDMI4 TMDS OUT HDMI5 HDMI RECEIVER OUT0 VIDEO DECODER...
Page 44
3.6. Protection History Display Mode 3.6.1. Actions This mode enables the unit to record and display the event when the THERMAL, ASO or DC protection is activated. If protections have been activated multiple times, the latest protection operation is recorded. 3.6.2.
Page 45
3.6.4. Clearing the Protection History There are two ways to clear the protection history. (a) Activate Protection History Display Mode. Press the "STATUS" button to display the protection history. Press and hold the "DIMMER" button for 3 seconds. P R T : D C Press and hold the "DIMMER"...
Page 46
3.7. Operation Info Mode 3.7.1. Actions This mode enables the unit to display the accumulated operating time, power on count and each protection count. 3.7.2. Starting up While holding down buttons "ZONE2 SOURCE" and "STATUS" simultaneously, press the power button to turn on the power.
Page 47
3.8. TUNER STEP mode (U / N only) 3.8.1. Actions This is a special mode for enabling reception STEP of the ANALOG TUNER to be changed. 3.8.2. Starting up While holding down buttons "ZONE2 SOURCE" and "STATUS" simultaneously, press the power button to turn on the power.
4. Protection Pass Mode 4.1. Actions • This mode allows the power to be turned on without activating protections. • This mode functions in the same way as normal power-on, except that protections are not activated. 4.2. Operations While holding down buttons "DIMMER", "STATUS" and "SOUND MODE" simultaneously, press the power button to turn on the power.
6. CY920 Initialization Mode 6.1. Actions The following items are initialized. (1) Favorites (2) Quick Select (3) Presets (4) Internet Radio Recently Played (5) Flickr contacts (6) User ID (7) Resume Playback station 6.2. Operations While the power is on, hold down buttons "ZONE2 SOURCE" and "DIMMER" for at least 3 seconds. Initializing Display I n i t i a l i z i n g I n i t i a l i z i n g .
JIG FOR SERVICING Use the following jigs (extension cable kit) when repairing the PCBs. Order with your dealer for the jigs your dealer if necessary. CAUTION : Incorrect connections may cause malfunction. • Connection of Jig for HDMI PCB ---Items to Be Prepared--- 8U-110084S EXTENSION UNIT KIT 1Sets...
Page 51
(3) Remove the HDMI PCB from the chassis and turn it over. Place an insulation sheet larger than the PCB underneath the HDMI PCB. Connect the earth of the PCB to the chassis using an earth wire, etc. PCB HDMI Insulation sheet CHASSIS-HDMI CONNECTOR CHASSIS-COMPOSIT CONNECTOR...
PROCEDURE AFTER REPLACING THE MICROPROCESSOR, ETC. The procedure after replacing the u-COM (microprocessor), flash ROM, etc. is as follows. Proce- dure after PCB Name Ref. No. Description Remark Replace- ment R5F564MJCDFC 32BIT SOFTWARE : Main HDMI U1018 HDMI U1025 MX25L6406EM2I-12G 64M SOFTWARE : DSP1 ROM HDMI U1027...
FIRMWARE UPDATE PROCEDURE 1. Updating via USB The latest firmware can be downloaded to a USB memory for updates. 1.1. Connecting to the USB Memory (1) Preparation • Use a memory that supports USB2.0. • USB format : Prepare a USB memory formatted in FAT16 or FAT32. •...
Page 54
1.3. File structure on USB Memory Copy the update files to the USB memory with the following structure. USB memory root Model Name Model Area Product ID NR1606U North America (U) 100100400100 NR1606N Europe (N) 100100400200 NR1606K China (K) 100100400500 NR1606F Japan (JP) 100100400400...
Page 55
1.8. The firmware update finishes. When the update is completed, the following message appears on the display, then the unit returns to the normal status. Display U p d a t i n g C o m p l e t e ---Cautions on Firmware Update--- •...
Page 56
1.10. About the error codes See the table below for error codes and details of faults when the firmware is updated through USB memory. Error USB Update Error Display Details of Error code Remedies Code Disconnect and reconnect the USB Unable to detect USB.
Page 57
Error USB Update Error Display Details of Error code Remedies Code This unit automatically retries the request several times. Wait until the Error in Verify after rewriting Main Display stops. If the Display stops at the U p d a t e C h e c k N G (Check Sum Error).
Page 58
Error USB Update Error Display Details of Error code Remedies Code This unit automatically retries the request several times. Wait until the Error notification received while Display stops. If the Display stops at the U p d a t i n g f a i l requesting the Firmware Info.
Page 59
Error USB Update Error Display Details of Error code Remedies Code This unit automatically retries the request several times. Wait until the Setup failure of the XModem Display stops. If the Display stops at the U p d a t i n g f a i l transfer method.
Page 60
Error USB Update Error Display Details of Error code Remedies Code This unit automatically retries the request several times. Wait until the No Firmware File in USB. Display stops. If the Display stops at the F i l e s N o t F o u n d Error display, press and hold the "Power operation"...
Page 61
1.11. Device display during the firmware update Display the device being updated and the update progress. Target device USB Update Display Error code when an error occurs 10 - 16 Main CPU 36 - 3D M a i n : * * % * * * m i n 50 - 52 Audio PLD...
2. Updating via DPMS Download the latest firmware from our website and update the firmware. 2.1. Network Connection (1) System Requirements • Internet Connection by Broadband Circuit • Modem • Router • Ethernet cable (CAT-5 or greater is recommended) (2) Setting Internet Computer Modem...
Page 63
2.3. About the error codes See the following table for details on the error code display, details of the error code, remedies when updating the firm- ware via DPMS. (DPMS : D&M Product Management Server) Error DPMS Update Error Display Details of Error code Remedies Code...
Page 64
Error DPMS Update Error Display Details of Error code Remedies Code Abnormal data in Update Packet Turn off and on the power. Updating received from CY920 (Packet No U p d a t i n g f a i l starts automatically.
Page 65
Error DPMS Update Error Display Details of Error code Remedies Code Check the network connection. Carry DPMS connection Time Out Error. out the update in an environment that C o n n e c t i o n F a i l 3 9 has little network load.
Page 66
Error DPMS Update Error Display Details of Error code Remedies Code NACK received in response or Turn off and on the power. Updating no response from Sub for the "L" U p d a t i n g f a i l starts automatically.
Page 67
Error DPMS Update Error Display Details of Error code Remedies Code Check the network connection. Carry IP Address acquisition failure out the update in an environment that C o n n e c t i o n F a i l A 1 (Time Out).
Page 68
Device display during the firmware update Display the device being updated and the update progress. Target device DPMS Update Display Error code when an error occurs 10 - 16 Main CPU M a i n : * * % * * * m i n 36 - 3F 50 - 52 Audio PLD...
ADJUSTMENT Adjusting Idling Current 1. Preparation (1) Prepare a DC voltmeter. (2) Place the unit under normal usage conditions, away from highly ventilated areas such as next to an air conditioning machine or electric fan. The set requires an ambient temperature of 15℃ to 30℃ and standard humidity.。 (3) Settings of This Unit •...
SURROUND MODES AND PARAMETERS Surround Parameter Loudness Dynamic Low Frequency Sound mode Subwoofer Level Dialog Control Dialog Level Adjust Cinema EQ Management Compression Adjust Direct/Pure Direct (2-channel) z5 Direct/Pure Direct (Multi-channel) z5 Stereo Multi Ch In Dolby Surround DTS Neural:X Dolby Digital Dolby Digital Plus Dolby TrueHD...
TROUBLE SHOOTING 1. POWER 1.1. The unit does not power on The unit does not power on Does the power indicator Does the power indicator on on the front panel flash in the front panel flash in red green or white when the when the power is turned on? power is turned on? Is a fuse blown?
2. Analog video CVBS / COMPONENT / HDMI OUT NG Input CVBS Input COMPONENT Input Function : CBL / SAT Function : CBL / SAT HDMI To "3 HDMI/DVI" To "A" <HDMI PCB> test point CLP1001 HDMI PCB [MP] N1039 N1019 CLP1003 N1017...
Page 73
Input CVBS / COMPONENT Check the input signal to the VIDEO DECODER. Can a signal be confirmed at the follow- ing points? HDMI PCB : R2092 Input CVBS : Check B Check the connection between the COMPONENT-Y : R2089 boards. Input COPONENT : Check C COMPONENT-Cb : R2091...
Page 74
Input CVBS Check the settings of each IC. Are the following voltages set? HDMI PCB HDMI PCB faulty. N1039 - 12 pin : Hi (3.3 V) N1039 - 13 pin : Hi (3.3 V) N1039 - 14 pin : Lo (0 V) Extend the HDMI PCB using the jig.
Page 75
Input COMPONENT Check the settings of each IC. Are the following voltages set? HDMI PCB faulty. HDMI PCB N1039 - 11 pin : Lo (0 V) N1039 - 15 pin : Hi (3.3 V) Extend the HDMI PCB using the jig. Is the power voltage being output correctly? Check the connection between the FRONT...
(7) Are the HDMI output settings of the Blu-ray/DVD player correct? and set the HDMI output correctly. (8) When using a Marantz Blu-ray/DVD player, is the "HDMI" indicator of the fluorescent display lit? Proceed to YES when using a Blu-ray/DVD player produced by other manufactures.
Page 77
(11) Are a picture and sound output when a different Blu-ray/DVD The Blu-ray/DVD player is faulty. player is used? Check the TV. Use a TV that supports HDCP. Computer monitors can- (12) Does the TV support HDCP? not be used. If the TV does not support 1080P/4K, a picture cannot be (13) Does the TV support 1080P/4K? output even if the Blu-ray/DVD player is set to 1080P/4K.
4. AUDIO 4.1. AUDIO CHECK No audio output CHECK1 INPUT SURROND MODE SOURCE Check the ANALOG AUDIO BLOCK Audio output OK? ANALOG 2CH DIRECT ANALOG CHECK2 INPUT SURROND MODE SOURCE Check the DIGITAL AUDIO BLOCK Legacy Audio output OK? COAX or OPT (PCM or DolbyDigital or dts…) CHECK3 INPUT...
Page 79
4.2. Power AMP (AMP PCB) No audio output. Protection is activated. Is the power transistor open or short circuited? Replace the power transistor. 2SB1560 / 2SD2390 Is the emitter resistor of the power transistor open? Replace the emitter resistor. 0.47 Ω Is the base resistor of the power transistor open? Replace the base resistor.
Page 80
4.3. Analog audio No audio output. Is a voltage of ± 8 V supplied to AV Repair the ± 8 V power supply. PCB CP5201? Is there an audio signal in AV PCB Repair the power amplifier. CN4801? Connect the connectors correctly. Is the connector correctly connected to the HDMI PCB? Repair the HDMI PCB.
5. Network / Bluetooth / USB 5.1. Cannot connect to the network Check the connection environment Insert the LAN cable correctly and then turn on the pow- Is the LAN cable correctly inserted? er again. Check the connection environment Set the IP address, etc. correctly. When the static IP address is used, check that no other Are the network settings of this unit correct? devices have the same IP address and that the subnet...
Page 82
Can the NET3.3V output voltage (3.3 V) Is E_POWER1 (U1018 uCOM 132 pin) The circuit of E_POWER1 between to Q1071 (FET-SW) be confirmed? "Hi" ? U1018 and Q1071 are faulty. The circuit around Q1071 (FET-SW) is faulty. Can the NET1.2V output voltage (1.2 V) Is E_POWER4 (U1018 uCOM 132 pin) The circuit of E_POWER4 between to U1070 (DC-DC Conv.) be confirmed?
Page 83
5.2. Cannot establish a Bluetooth connection Check the Bluetooth device being used Is the Bluetooth device compatible with the A2DP profile? Use a device that is A2DP profile compatible. Is the Bluetooth function enabled on the Bluetooth device? Enable the Bluetooth function and try connecting again. Checking the unit Is the Wi-Fi/BT antenna cable inserted correctly into CY920? Connect the Wi-Fi/BT antenna cable correctly.
Page 84
5.3. Cannot recognize the connected USB device Check the USB device being used Is a USB hub being used? Do not use a USB hub. This unit supports devices in the FAT16- and FAT32-for- Is the USB device supported by this unit? matted mass storage class, MTP-compatible devices and iPod devices (except for some models).
6. SMPS DC 5V is not output. Replace the IC4140 (TOP268VG) and Is IC4140 (TOP268VG) damaged? D4142 / D4143 /D4144 / D4145. Is the fuse (F4140) functioning proper- Replace the damaged part. Is D4142, D4143, D4144, D4145 or IC4140 damaged? Are there any short circuits caused by Repair the short circuited area on the the soldering on the PCB?
Page 87
Operation waveform for each part After primary side rectification Primary drain (Caution: High voltage, electric shock) (Caution: High voltage, electric shock) OPTION OPTION After secondary rectifications T4140 EE2525 OPTION OPTION BKT4142 OPTION IC4140 IC_TOP268VG SMPS unit (Unloaded)
LEVEL DIAGRAM NR1606 LEVEL DIAGRAM FRONT ch BD34704 ANALOG H/POUT + SPEAKER LINE IN GAIN + PCM1690 + PCM9211 + - - MUTE PRE OUT ZONE2 EXT IN (SR5010 ONLY) +30dB SP OUT 4.48Vrms/8Ω MAX SIGNAL LEVEL 0dBFS +20dB +20dB 1.41Vrms PCM1690 DOLBY LIMIT LEVEL (ALLch-3dBFS)
Page 90
NR1606 LEVEL DIAGRAM CENTER ch BD34704 + SPEAKER GAIN PCM1690 (SR5010 ONLY) + + - - MUTE PRE OUT EXT IN (SR5010 ONLY) +30dB SP OUT 4.48Vrms/8Ω 0dBFS MAX SIGNAL LEVEL 1.41Vrms +20dB +20dB DOLBY LIMIT LEVEL (ALLch-3dBFS) 0dBFS +29dB +10dB +10dB -10dBFS...
Page 91
NR1606 LEVEL DIAGRAM SUBWOOFER ch BD34704 MUTE PRE OUT GAIN PCM1690 + + (SR5010 ONLY) - - MUTE PRE OUT EXT IN (SR5010 ONLY) +30dB MAX SIGNAL LEVEL Config1 DOLBY LIMIT LEVEL (ALLch-3dBFS) 0dBFS 0.88Vrms +20dB +20dB 0dBFS +10dB +10dB -10dBFS PREOUT 317mVrms...
Page 92
NR1606 LEVEL DIAGRAM SURROUND ch BD34704 + SPEAKER GAIN PCM1690 (SR5010 ONLY) + + - - MUTE PRE OUT EXT IN (SR5010 ONLY) +30dB SP OUT 4.48Vrms/8Ω 0dBFS MAX SIGNAL LEVEL 1.41Vrms +20dB +20dB DOLBY LIMIT LEVEL (ALLch-3dBFS) 0dBFS +29dB +10dB +10dB -10dBFS...
Page 93
NR1606 LEVEL DIAGRAM SURR.BACK ch BD34704 + SPEAKER GAIN PCM1690 + (SR5010 ONLY) + - - MUTE PRE OUT EXT IN (SR5010 ONLY) +30dB SP OUT NON CLICP MAX SIGNAL LEVEL 4.0Vrms 4.48Vrms/8Ω SP OUT(D/A OUT) 0dBFS DOLBY LIMIT LEVEL 1.41Vrms(ALLch-3dBFS) 1.41Vrms +20dB +20dB...
Page 94
NR1606 LEVEL DIAGRAM ZONE2 BD34704 from F-ch from DA SB-ch SPEAKER + LINE IN + MAIN NET/USB DAC + ZONE2 +30dB SP OUT 0dBFS PCM5100 2.0Vrms MAX SIGNAL LEVEL 2.00Vrms +20dB +20dB 0dBFS -10dBFS +10dB +10dB -20dBFS(DIG.IN) -2.0dB LINE IN 200mV -20dBFS PREOUT...
BLOCK DIAGRAM ANALOG AUDIO DIAGRAM H/P-L HEADPHONE OUT TO DIGITAL AUDIO BLOCK TO DIGITAL AUDIO BLOCK TO DIGITAL AUDIO BLOCK H/P-R SPK OUT SBL(FL-B/FL-H/BI-AMP/ZONE) SBR(FR-B/FR-H/BI-AMP/ZONE) DM920_R/L ANA_FL DSP_FL ANALOG ANA_FR SAT_CBL INPUT DSP_FR 2.2ch PREOUT DSP_C TUNER DSP_SW FM/AM MIC(Mini Jack) DSP_SL DSP_SR DSP_SBL...
Page 97
VIDEO DIAGRAM ADV8195 FRONT HDMI TMDS IN BUFFER OUT0 TMDS OUTPUT HDMI OUT TMDS IN HDMI1 HDMI2.0 RX MN864788 HDMI2.0 TX (2.2 4 INPUTS) MN864788 HDMI2 MX25L12835FMI HDMI IN TMDS OUT TMDS IN HDMI3 OUT1 HDMI4 TMDS OUT HDMI5 OUT0 HDMI RECEIVER VIDEO DECODER HDMI i/p Scaler_TX_OSD...
NET PHY TO 1B TO CPU DM920_SPDIF NET/USB_MCK NET/USB_LRCK DIR/A.PLD NET/USB_BCK NET/USB_DATA_/FR TO 2B NET/USB_DATAF/FL FROM NET3.3V NET2.5V D.SUPPLY NET1.8V NET1.2V DGND TO 3B R1207 OPEN R1208 OPEN NET3.3V C1172 OPEN-1608 920PCK C1173 100N-K 920VD0 C1174 1N-K 920VD1 U1005 MFI337S3959 920VD2 920VD3 ADV8003...
CPU LEVEL CHG TO DIGITAL CNT TO 5B FROM REMOTE3.3V SWM3.3V D.SUPPLY M3.3V DGND TO 6B SWM3.3V R1366 DGND R1379 R1385 OPEN OPEN 14 13 12 11 10 TO CPU TO 7B SCHEMATIC DIAGRAMS (04/26) SCH04_CPU_LEVEL_CHG GND LINE POWER+ LINE POWER- LINE ANALOG AUDIO DIGITAL AUDIO...
DIR/A.PLD TO A2 TO A7 TO 8D TO B2 TO D7 TO C6 FROM HDMI RX FROM HDMI SW1 FROM HDMI SW2 NET PHY HDMI TX ADV7850 *FILTER COMPONENTS VALUE TYPE TOLERANCE R1907 680 ¥Ø METAL FILM OR CARBON 0 ¥Ø ¡Â...
TO E1 TO D9 TO C5 TO E0 MAIN DAC FROM FROM FROM FROM DIR/A.PLD DIR/A.PLD DIR/A.PLD DA+5V A/DIN_R DAGND A/DIN_L DAGND OPEN-1608 R1997 DACRTNGND R1998 OPEN-1608 DA+5V C2137 R1999 DAGND OPEN-1608 100-1608 DAGND R2002 TO DIGITAL CNT C2143 10U-K-2012 100-1608 DAGND R2010...
CN5402 CVBS INPUT SW NJM2595MTE1 u-COM CON IC CON OUT PUT NR1606 VINA VINC SW1 SW2 SW4 SW5 VINB IN 1 MUTE IN 2 MUTE IN 3 CBL/SAT IN 4 IN 5 BLU-RAY FRONT_CNT 3/4 G8 TO CP4611 COMPONENT INPUT SW (NJM2586AVC3) INPUT MUTE(PS)
CP4800 VR4800 1K(B)-V TO CN4000 CP4801 TO CN4801 CP4802 TO CN4005 VR4801 1K(B)-V CN4800 TO N1019 VR4802 1K(B)-V TO 6E TO 5E SCHEMATIC DIAGRAMS (22/26) SCH22_AMP1 GND LINE POWER+ LINE POWER- LINE ANALOG AUDIO DIGITAL AUDIO TMDS SIGNAL VIDEO SIGANL COMPONENT (Y)
TO E5 TO E6 VR4803 1K(B)-V VR4804 1K(B)-V VR4805 1K(B)-V CP4803 TO CN4003 VR4806 1K(B)-V SCHEMATIC DIAGRAMS (23/26) SCH23_AMP2 GND LINE POWER+ LINE POWER- LINE ANALOG AUDIO DIGITAL AUDIO TMDS SIGNAL VIDEO SIGANL COMPONENT (Y)
SMPS_REG_FCNT 3/3 HDMI DIGITAL CNT E8 OTHER USE NR1606 USE CP4013 TO N1039 CP4615 CP4615 20010WR-04 VIDEO+5V VIDEO_GND SMPS_REG_RC5_FCNT 2/4 B3 VIDEO_GND VIDEO-5V TO CN4607 CP4611 CP4614 TO CN5402 TO CN5200 SCHEMATIC DIAGRAMS (26/26) SCH26_FRONT CNT GND LINE POWER+ LINE POWER- LINE ANALOG AUDIO DIGITAL AUDIO...
PACKING VIEW PACKING VIEW Please see the last chapter for the part list. MANUAL POLYBAG ASSY POLYBAG CODE: 6337-04006-201-0S POLYBAG CODE: 6337-21071-900-0S ZIPPER (A4size) Notes on RADIO ( ALL ) SAFETY INST. ( ALL ) JAPAN POST CARD ( F Only) WARRANTY ( U Only ) SPK WIRE LABEL ( ALL ) ZIPPER BAG (A5size)
SEMICONDUCTORS Only major semiconductors are shown, general semiconductors etc. are omitted to list. The semiconductor which described a detailed drawing in a schematic diagram are omitted to list. 1. IC's R5F564MJCDFC (HDMI : U1018) R5F56108VNFP Terminal Functions Pin Name Symbol Function Pu/Pd STBY...
Page 136
Pin Name Symbol Function Pu/Pd STBY STOP STBY EXTAL/P36 EXTAL Oscillator connection(12MHz) POWER pin UPSEL/P35(IN)/NMI DSP FLAG3 DSP control pin P34/SCK6/SCK0/IRQ4 BDOWN Power failure detection pin P33/TIOCD0/RXD6/RXD0/ RC IN Remote control signal input pin IRQ3-DS NC(NR1606(EU/ P32/TIOCC0/TXD6/TXD0/ JP))/FLASHER FLASHER (RC-5) input pin (NR1606 :U Version Only , IRQ2-DS IN(NR1606(NA)/ SR5010 : All Version)
Page 137
Pin Name Symbol Function Pu/Pd STBY STOP STBY P75/SCK11 CEC POWER2 CEC STANDBY SUPPLY control pin(CEC STANDBY) DSP ROM WRITE DSP ROM writing control pin(DSP writing:H) PC1/SCK5/IRQ12 DAC.PLD ERR PLD ERROR detection pin POWER pin PC0/IRQ14 H/P RL HEADPHONE RLY control pin FRONT RL SPEAKER RELAY control pin PB7/TXD9...
Page 138
Pin Name Symbol Function Pu/Pd STBY STOP STBY PD4/IRQ4/AN112 Unused DE_RST HDMI ADV7850 RESET control pin PD3/IRQ3/AN111 788_1_HINT HDMI MN864788(TX) HDMI INT input pin 788_1_RST HDMI MN864788(TX) RESET control pin ※ POWER pin PD2/IRQ2/AN110 788_2_HINT HDMI MN864788(RX) HDMI INT input pin 788_2_RST HDMI MN864788(RX) RESET control pin ※...
Page 143
W9864G6KH-5 (HDMI : U1023) W9864G6KH W9864G6KH-5 Pin description 5. PIN DESCRIPTION PIN NUMBER PIN NAME FUNCTION DESCRIPTION Multiplexed pins for row and column address. Row address: A0 A11. Column address: A0 A7. 23 ~ 26, 22, Address A0 A11 A10 is sampled during a precharge command to 29 ~35 determine if all banks are to be precharged or bank selected by BS0, BS1.
Page 144
W9864G6KH-5 Block diagram CLOCK BUFFER CONTROL SIGNAL GENER ATOR COMMAND DECODER COLUMN DECODER COLUMN DECODER CELL ARRAY CELL ARRAY BANK #0 BANK #1 MODE REGIST ER SENSE AMPLIFIER SENSE AMPLIFIER ADDRESS BUFFER DATA CONTROL CIRCUIT BUFFER COLUMN REFRESH COUNTER COUNTER COLUMN DECODER COLUMN DECODER CELL ARRAY...
Page 145
PCM1690 (HDMI : U1048) PCM1690 Pin Function TERMINAL PULL- DESCRIPTION NAME DOWN TOLERANT RSV2 — — — Reserved, tied to analog ground RSV1 — — — Reserved, left open RSV2 — — — Reserved, tied to analog ground RSV1 — —...
Page 146
TERMINAL PULL- DESCRIPTION DOWN TOLERANT NAME VOUT1+ Positive analog output from DAC1 VOUT1- Negative analog output from DAC1 PCM1690 RSV2 — — — Reserved, tied to analog ground AGND2 — — — Analog ground 2 VCC2 — — — Analog power supply 2, +5 V RSV2 —...
Page 147
SLAS764 – MAY 2011 www.ti.com DEVICE INFORMATION TERMINAL FUNCTIONS, PCM510x PCM5100 (HDMI:U1052) PCM510X (top view) Table 2. TERMINAL FUNCTIONS, PCM510x TERMINAL DESCRIPTION NAME CPVDD Charge pump power supply, 3.3V CAPP Charge pump flying capacitor terminal for positive rail CPGND Charge pump ground CAPM Charge pump flying capacitor terminal for negative rail VNEG...
Page 148
ゾーン 3 対応 ゾーン用の 2ch ボリューム搭載 2 線シリアルバスコントロールは、3.3/5V に対応 SQFP-T80C 用途 BD34704KS2 (AV : IC4200) AV レシーバ、ホームシアタシステムに最適。 基本アプリケーション回路 Figure 1. 応用回路例 PIN No. SYMBOL PIN No. SYMBOL PIN No. SYMBOL PIN No. SYMBOL SBLIN INR9(SBRIN2) SRIN INL9(SBLIN2) ○製品構造:シリコンモノリシック集積回路...
Page 149
G Internal 75Ω Driver GENERAL DESCRIPTION PACKAGE OUT G Bipolar Technology G Package Outline DIP16,DMP16 The NJM2586A is a wide band 3-input 1-output 3-circuit video amplifier. It is suitable for Y, Pb, and Pr signal because frequency range is 50MHz.The NJM2586A is suitable for AV receiver, STB, I PIN CONFIGURATION and BLOCK DIAGRAM and other high quality AV systems.
Page 152
SPK_SCNT SPK_SCNT PCB ASS'Y ※Parts indicated by "nsp"on this table cannot be supplied. ※The parts listed below are only for maintenance. Therefore they might differ from the parts used in the unit in appearances or dimensions NOTE:The symbols in the column Remarks indicate the following destinations. U : North America model N : Europe model K : China model F : Japan model B : Black model SG : Silver Gold model...
Page 153
SPK_SCNT REF No. Part No. Part Name Remarks Q'ty New Ver L4000-4006 COIL,FILTER-INDUCTOR SP-2507 1.0 PI*2UEW TURNS=7T SPRING COIL D330900001330S N4600 CN.FPC 1.0MM 1.0-11S-4PW 4P AN DIP TOP CONTACT L130100110450S RLY4000-4003 963682100280D RELAY JZC-42F/012-2HST 24.4*12.8*24.8mm G680060103010S RLY4004 963682100560S RELAY HFD27/012-S 24V 2A 2회로 2접점(SMALL SIGNAL) G680240202080S RLY4005 963682100510S...
Page 154
REG_SMPS_FCNT REG_SMPS_FCNT PCB ASS'Y ※Parts indicated by "nsp"on this table cannot be supplied. ※The parts listed below are only for maintenance. Therefore they might differ from the parts used in the unit in appearances or dimensions NOTE:The symbols in the column Remarks indicate the following destinations. U : North America model N : Europe model K : China model F : Japan model B : Black model SG : Silver Gold model...
Page 155
REG_SMPS_FCNT REF No. Part No. Part Name Remarks Q'ty New Ver ! F4601,4602 963644101960S FUSE,MICRO 1.6A 250V SS-5 TIME DELAY RADIAL LEADED FUSE G658162250050S ! F4603,4604 963652010500S FUSE GLASS TUBE 20MM T1.6A/250V-IVBSUCPCcUR S506 N751501601160S JK4140 CN.WAFER 7.92MM PLUG YW396-03AV 2P L108396030010S ! L4140 963111101060S...
Page 157
FRONT REF No. Part No. Part Name Remarks Q'ty New Ver U4400 943172100150S DISPLAY,FLT 018BT021GINK 129*25*6.1 GREEN /AVR1913 K530180210010S VEC4400 963667100170D SW,ENCODER EC16B12SAAD4ZZZ G121161200070S VEC4401 963667012360S SW,ENCODER EC16B24T01D4ZZZ 24PLUSE 360' L=25MM G121162400060S...
Page 158
AV PCB ASS'Y ※Parts indicated by "nsp"on this table cannot be supplied. ※The parts listed below are only for maintenance. Therefore they might differ from the parts used in the unit in appearances or dimensions NOTE:The symbols in the column Remarks indicate the following destinations. U : North America model N : Europe model K : China model F : Japan model B : Black model SG : Silver Gold model...
Page 159
REF No. Part No. Part Name Remarks Q'ty New Ver R5411-5413 R,CHIP THICK 75-J,1/16W-1608REEL C20007506M160S R5414,5415 R,CHIP THICK 150-J,1/16W-1608REEL C20001516M160S R5416,5417 R,CHIP THICK 160-J,1/16W-1608REEL C20001616M160S R5418,5419 R,CHIP THICK 150-J,1/16W-1608REEL C20001516M160S R5420,5421 R,CHIP THICK 160-J,1/16W-1608REEL C20001616M160S R5422,5423 R,CHIP THICK 150-J,1/16W-1608REEL C20001516M160S R5424,5425 R,CHIP THICK 160-J,1/16W-1608REEL C20001616M160S...
Page 160
REF No. Part No. Part Name Remarks Q'ty New Ver C5416 C,ELECT GE 85C 1UF-M/50V,5*11-5RE.SMS SY (Pb Free) D040010087150S C5417 C,CERAMIC CHIP HIK X7R)0.1UF-K/50V-1608REEL D011104577160S C5418 C,ELECT GE 85C 1UF-M/50V,5*11-5RE.SMS SY (Pb Free) D040010087150S C5419 C,CERAMIC CHIP HIK X7R)0.1UF-K/50V-1608REEL D011104577160S C5420 C,ELECT GE 85C 1UF-M/50V,5*11-5RE.SMS SY (Pb Free) D040010087150S...
Page 161
HDMI HDMI PCB ASS'Y ※Parts indicated by "nsp"on this table cannot be supplied. ※The parts listed below are only for maintenance. Therefore they might differ from the parts used in the unit in appearances or dimensions NOTE:The symbols in the column Remarks indicate the following destinations. U : North America model N : Europe model K : China model F : Japan model B : Black model SG : Silver Gold model...
Page 162
HDMI REF No. Part No. Part Name Remarks Q'ty New Ver R1043 R,CHIP THICK 47K-J,1/16W-1005REEL C20004736M101S R1044,1045 R,CHIP THICK 0-J,1/16W-1005REEL C20000006M101S R1052 R,CHIP THICK 1.8K-J,1/16W-1005REEL C20001826M101S R1053 R,CHIP THICK 0-J,1/16W-1005REEL C20000006M101S R1055 R,CHIP THICK 1.8K-J,1/16W-1005REEL C20001826M101S R1057,1058 R,CHIP THICK 1.8K-J,1/16W-1005REEL C20001826M101S R1060-1062 R,CHIP THICK 47-J,1/16W-1005REEL...
Page 163
HDMI REF No. Part No. Part Name Remarks Q'ty New Ver R1371 R,CHIP THICK 10K-J,1/16W-1005REEL C20001036M111S R1393,1394 R,CHIP THICK 4.7K-J,1/16W-1005REEL C20004726M101S R1452 R,CHIP THICK 100-J,1/16W-1005REEL C20001016M101S R1453,1454 R,CHIP THICK 10K-J,1/16W-1005REEL C20001036M111S R1455,1456 R,CHIP THICK 1K-J,1/16W-1005REEL C20001026M101S R1457,1458 R,CHIP THICK 4.7K-J,1/16W-1005REEL C20004726M101S R1459 R,CHIP THICK 10K-J,1/16W-1005REEL...
Page 164
HDMI REF No. Part No. Part Name Remarks Q'ty New Ver R1717,1718 R,CHIP THICK 10K-J,1/16W-1005REEL C20001036M111S R1731 R,CHIP THICK 33-J,1/16W-1005REEL C20003306M101S R1732 R,CHIP THICK 0-J,1/16W-1005REEL C20000006M101S R1733,1734 R,CHIP THICK 10K-J,1/16W-1005REEL C20001036M111S R1735 R,CHIP THICK 33-J,1/16W-1005REEL C20003306M101S R1736 R,CHIP THICK 200K-F,1/16W-1608REEL C20002044M160S R1737 R,CHIP THICK 220K-F,1/16W-1608REEL...
Page 165
HDMI REF No. Part No. Part Name Remarks Q'ty New Ver R1920,1921 R,CHIP THICK 33-J,1/16W-1005REEL C20003306M101S R1922 R,NETWORK A-TYPE 33-J 1/16W SMD(1005)*4 WA04X C180330042100S R1923 R,CHIP THICK 33-J,1/16W-1005REEL C20003306M101S R1924 R,NETWORK A-TYPE 33-J 1/16W SMD(1005)*4 WA04X C180330042100S R1925-1927 R,CHIP THICK 33-J,1/16W-1005REEL C20003306M101S R1929 R,CHIP THICK 33-J,1/16W-1005REEL...
Page 166
HDMI REF No. Part No. Part Name Remarks Q'ty New Ver R2120 R,CHIP THICK 470-D,1/16W-1608REEL C20004711M160S R2121 R,CHIP THICK 10K-J,1/16W-1005REEL C20001036M111S R2123,2124 R,CHIP THICK 4.7K-J,1/16W-1005REEL C20004726M101S R2125 R,NETWORK A-TYPE 4.7K-J 1/16W SMD(1005)*4 WA04X C180472042100S R2126 R,CHIP THICK 10K-J,1/16W-1005REEL C20001036M111S R2127 R,CHIP THICK 47-J,1/16W-1005REEL C20004706M101S R2128...
Page 167
HDMI REF No. Part No. Part Name Remarks Q'ty New Ver C1429,1430 C,CERAMIC CHIP HIK X7R)1000PF-K/50V-1005REEL D011102177101S C1432 C,CERAMIC CHIP HIK X7R)0.1UF-K/16V-1005REEL D011104177101S C1434 C,CERAMIC CHIP HIK X7R)1000PF-K/50V-1005REEL D011102177101S C1435 C,CERAMIC CHIP HIK X7R)0.1UF-K/16V-1005REEL D011104177101S C1437 C,CERAMIC CHIP HIK X7R)1000PF-K/50V-1005REEL D011102177101S C1440 C,CERAMIC CHIP HIK X7R)0.1UF-K/16V-1005REEL...
Page 170
7CH_AMP 7CH_AMP PCB ASS'Y ※Parts indicated by "nsp"on this table cannot be supplied. ※The parts listed below are only for maintenance. Therefore they might differ from the parts used in the unit in appearances or dimensions NOTE:The symbols in the column Remarks indicate the following destinations. U : North America model N : Europe model K : China model F : Japan model B : Black model SG : Silver Gold model...
Page 171
7CH_AMP REF No. Part No. Part Name Remarks Q'ty New Ver R4863 R,CHIP THICK 10K-J,1/16W-1608REEL C20001036M160S R4864 963124500500S R,FIXED,M.O. RSD-R1-2WJ-0.22 3.5*8.6 P=5MM R.REEL N113136622820S R4866 R,CHIP THICK 5.6K-J,1/16W-1608REEL C20005626M160S R4870 R,CARBON FILM 1.2K-J,1/5W-52RE-AX C00001226P520S R4871 R,CARBON FILM 1K-J,1/5W-52RE-AX C00001026P520S R4872 R,CARBON FILM 33K-J,1/5W-52RE-AX C00003336P520S R4874...
Page 172
7CH_AMP REF No. Part No. Part Name Remarks Q'ty New Ver R5009,5010 R,CARBON FILM 220-J,1/5W-52RE-AX C00002216P520S R5011 963125012630S R,METAL FILM 100PPM 22-J,1W-5REEL C060022065050S R5012 R,CARBON FILM 150-J,1/5W-52RE-AX C00001516P520S R5013 R,CARBON FILM 270-J,1/5W-52RE-AX C00002716P520S R5014 R,METAL FILM 100PPM 1.2K-J,1W-5REEL C060012265050S R5015 R,METAL FILM 100PPM 47-J,1W-R.REEL C060047065060S R5016...
Page 173
7CH_AMP REF No. Part No. Part Name Remarks Q'ty New Ver C4866 C,CERAMIC CHIP T.C COG100PF-J/50V-1608REEL D010101167160S C4867 963133502490S C,FILM POLYESTER ST-0.00022UF-J/100V-5RE HPE221J2AP050T DAEHUNG D02022106C250S C4868 C,ELECT GE 85C 47UF-M/25V,5*11 KR3-025V470MC110-T/A5.0S KOSHIN D040470084550S C4869 C,ELECT GE 85C 22UF-M/50V,5*11-5RE.SMS SY D040220087060S C4870 C,ELECT GE 85C 100UF-M/50V,8*11.5 KR3-050V101MF115-T/A5.0S KOSHIN D040101087550S...
Page 174
KNOB NR1403U1B(MARANTZ) BLACK A3/VOLUME KNOB 5080212691000CN 5087212691100S 963412100790M KNOB NR1403/1603 SG A3/VOLUEM KNOB 5087212691100CN NUTS 5127210901000S 963419006180M DECORATION NR1501FB(MARANTZ) ABS BK HF380-9001 RING KNOB 5127210901000CN 5127210901100S 963419006190M DECORATION NR1501N1SG(MARANTZ) ABS SG HF380-8A529 RING KNOB 5127210901100CN 963421006200M BADGE NR1501FB(MARANTZ) SILVER/GRAY 11c AL 5630210678000S...
Need help?
Do you have a question about the NR1606/U1B and is the answer not in the manual?
Questions and answers