Page 1
AV Surround Receiver Click here! NR1508 Online service parts list http://dmedia.dmglobal.com/Document/DocumentDetails/23156 Online Parts List (P5 to P7) WEB owner’s manual (Release schedule) http://manuals.marantz.com/NR1508/NA/EN/index.php (March 2017) http://manuals.marantz.com/NR1508/EU/EN/index.php (April 2017) http://manuals.marantz.com/NR1508/AP/ZH/index.php (June 2017) CAUTION IN SERVICING ELECTRICAL MECHANICAL REPAIR INFORMATION UPDATING • For purposes of improvement, specifications and design are subject to change without notice.
CAUTION IN SERVICING SAFETY PRECAUTIONS NOTE FOR SCHEMATIC DIAGRAM NOTE FOR PARTS LIST INSTRUCTIONS FOR HANDLING SEMICONDUCTORS AND OPTICAL UNIT Online Parts List Accessing the Parts List Logging in to New SDI and Accessing the Parts List Accessing the Part List from the Model Asset Screen PRINTED CIRCUIT BOARDS Parts Table Downloading the Parts List as an Excel File Revision History...
SAFETY PRECAUTIONS ◎ Make a safety check after servicing! The following items should be checked for continued protection of the customer and the service Check that all screws, parts and wires removed or disconnected when servicing have been put back technician.
NOTE FOR SCHEMATIC DIAGRAM WARNING: Parts indicated by the z mark have critical characteristics. Use ONLY replacement parts recommended by the manufacturer. CAUTION: Before returning the set to the customer, be sure to carry out either (1) a leakage current check or (2) a line to chassis resistance check.
Page 5
Online Parts List Accessing the Parts List Logging in to New SDI and Accessing the Parts List (1) Click the URL link on the cover of the service manual. (1) Access New SDI from the URL below. <http://dmedia.dmglobal.com> (2) When the login screen is displayed, enter your username and password. (3) Enter the 5 letters shown as the blue CAPTCHA code as single-byte characters.
Accessing the Part List from the Model Asset Screen Downloading the Parts List as an Excel File (1) Display the model Asset from New SDI. (1) Displays the Parts List. Click the Download icon. (2) Click the section displayed as ▼ Link to Part Lists under the model name. NOTE : If the ▼...
Page 7
Searching Part Numbers or Ref. Numbers You can search a Parts List for part numbers or Ref. numbers. (1) Enter the part number or Ref. number in the search window of the Parts List, and press the search button. (2) The search results are displayed. The name of the sheet in which the search part is used and the part’s line are displayed.
CAUTION IN SERVICING. Initializing This Unit Make sure to initialize this unit after replacing the microcomputer or any peripheral equipment, or the digital PCB. 1. Press the power button to turn off the power. 2. While holding down buttons "TUNER PRESET CH +" and "INTERNET RADIO" simultaneously, press the power button to turn on the power.
Page 14
SCH05_CPU LEVEL CHG TO 2C TO A4 TO A7 TO 3C CPU LEVEL CHG TO DIGITAL CNT MN864787 MN864788 MAIN DAC STBY3.3V STBY5V FROM SWM3.3V D.SUPPLY M3.3V DGND TO 4C R1091 CEC_COM C1212 OPEN SWM3.3V R1094 CEC_OUT Q1057 R1095 R1096 OPEN OPEN 2SD2114K...
Page 16
SCH07_DIR APLD DIR/A.PLD TO 9C TO B7 TO B0 TO 0D TO 1D FROM FROM NET PHY NET PHY HDMI TX NET PHY DIR input CH1:D-DATA *FILTER COMPONENTS VALUE TYPE TOLERANCE RT1N141C Q2204 R1907 680 ohm METAL FILM OR CARBON 0 ohm 0.068UF FILM OR CERAMIC (CH OR C0G)
Page 17
SCH08_MAIN DAC TO C3 TO D5 TO D3 TO B6 TO D4 MAIN DAC FROM FROM FROM FROM FROM DIR/A.PLD DIR/A.PLD DIR/A.PLD DA+5V AD_VDCOM ADIN_LEGO_R DAGND2 ADIN_LEGO_L DAGND2 FROM DIGITAL CNT C2189 ADIN_VDCOM C2193 A/DIN_L TO C7 C2188 DAGND2 DAGND2 C2187 A/DIN_R C2185...
Page 18
SCH09_DSP TO D7 TO D6 TO B5 TO 8D FROM FROM NET PHY DIR/A.PLD MP:OPEN N1011 OPEN(1.0-16-6PB-2) DSP1CS DSP1MISO DSP1MOSI DSP1CLK DGND DA3.3V Q2203 RT1N141C 11 12 13 14 15 16 R2119 DSP input DATA MP:OPEN N1012 I2S(HD Audio) I2S(PCM Multi) OPEN(1.0-16-10PB-2) DSP1INF/FL I2S0...
Page 19
SCH10_NET PHY TO C1 TO C8 NET PHY FROM DIGITAL_CNT NET3.3V LEGO5V FROM D.SUPPLY NET_I2S2_DOUT NET_I2S2_BCKIN NET_I2S2_DIN NET_I2S2_LRCKIN R1331 DGND TO 9D NET_I2S0_DOUT. R1360 NET_I2S_BCLKOUT. NET_TDM_DOUT R1364 NET_I2S_LRCKOUT. NET_TDM_BCKIN C1190 100N-K NET_TDM_FSIN C1187 100N-K C1882 10N-K R1461 R1462 C1176 1N-K C1024 4.7U-K-1608 19 18 17...
LEVEL DIAGRAM FRONT ch NR1508 LEVEL DIAGRAM FRONT ch NJU72750 NJU72343 ANALOG H/POUT SPEAKER LINE IN + GAIN ADJ. AK4458VN AK5358B + + PREOUT - - to ZONE2 +30dB NJU72343 MAX. OUTPUT 4.2Vrms SP OUT Differential Out 4.48Vrms/8Ω AK4458 MAX SIGNAL LEVEL...
Page 39
CENTER, SURROUND, SURR.BCK ch NR1508 LEVEL DIAGRAM CENTER ch SURROUND ch SURR.BCK ch NJU72343 SPEAKER + GAIN ADJ. AK4458VN + + PREOUT - - +30dB NJU72343 MAX. OUTPUT 4.2Vrms SP OUT Differential Out 4.23Vrms/8Ω AK4458 MAX SIGNAL LEVEL 0dBFS +20dB DOLBY LIMIT LEVEL (ALLch-3dBFS) 0dBFS = +/-2.8Vpp=1.98Vrms...
Page 41
SURROUND ch NR1508 LEVEL DIAGRAM SURROUND ch NJU72343 SPEAKER + GAIN ADJ. AK4458VN + + PREOUT - - +30dB NJU72343 MAX. OUTPUT 4.2Vrms SP OUT MAX SIGNAL LEVEL Differential Out 4.23Vrms/8Ω DOLBY LIMIT LEVEL (ALLch-3dBFS) AK4458 +20dB 0dBFS 0dBFS = +/-2.8Vpp=1.98Vrms...
Page 42
ZONE2(LEGO) ch NR1508 LEVEL DIAGRAM ZONE2(LEGO) NJU72750 LINE IN To MAIN To ZONE2 PCM9211 To LEGO +30dB +20dB +20dB PCM9211 0dBFS=1.06Vrms +10dB +10dB -10dBFS LINE IN 200mV -8.5dB -20dBFS A/D IN -10dB -10dB 75.2mVrms (-23.0dBFS) -30dBFS -20dB -20dB -40dBFS -30dB...
BLOCK DIAGRAM ANALOG AUDIO DIAGRAM NR1508 ANALOG AUDIO DIAGRAM TO DIGITAL AUDIO BLOCK TUNER TUNER_L BUFFER INVERTING ALL MODEL : FM/AM TUNER_R 7-INPUT/3-OUT 8-CH VOLUME NJU72750 MIC(Mini Jack) H/P-L HEADPHONE OUT NJU72343 7-INPUT/3-OUTPUT InA1 NJU72750 H/P-R 8-CH VOLUME InA2 NJU72343...
Page 44
DIGITAL AUDIO DIAGRAM NR1508 DIGITAL AUDIO DIAGRAM ADV7623 HDMI TRANSCEIVER KEY_MATRIX 10MHz OUT0 MN864787 CON MN864788 CON ADV7623 MAIN MICOM R5F5631FDDFB DATA FUNCTION TMDS TMDS OUT0 OSD DATA TUNER CONT IPOD TMDS TMDS POWER CONT HDMI4 MUTE RELAY TMDS TMDS...
WIRING DIAGRAM ANT_2 ANT_1 NR1508 WIRING BLOCK DIAGRAM AC CORD HDMI PCB LEGO MODULE MAIN + SPK PCB WiFi_ANTENNA WiFi_ANTENNA 40P CARD CABLE 23P CARD CABLE FRONT CNT PCB 13P WIRE(RLY) AV PCB MAIN POWER TRANS 5P WIRE SMPS PCB...
Page 48
SEMICONDUCTORS Only major semiconductors are shown, general semiconductors etc. are omitted to list. The semiconductor which described a detailed drawing in a schematic diagram are omitted to list. 1. IC's R5F5631FDDFB(DIGITAL_MCU : IC751) Pin Name Symbol Pu/Pd STBY STOP Function STBY Ground pin EXTAL/P36...
Page 49
Pin Name Symbol Pu/Pd STBY STOP Function Pin Name Symbol Pu/Pd STBY STOP Function STBY STBY Pins for setting the boot mode(select the Boot Mode or Protection detect signal input pin (for DC and ASO) (A/D PC7/TXD8/IRQ14 PE4/AN2 DC_DET/ASO SW3VPu User Boot Mode) converter) HDMI transceiver w/ GUI(ADV7623) control pin (for...
ADSP21487KSWZ-2B (DIGITAL : U1021) W9864G6KH-6(DIGITAL : U1020) PIN 1 GND PAD (PIN 177) at BOTTOM W9864G6KH TOP VIEW (PINS DOWN) Pin description 5. PIN DESCRIPTION PIN NUMBER PIN NAME FUNCTION DESCRIPTION Multiplexed pins for row and column address. Pin Name Pin No.
AK4458VN 40 +105 C (Exposed pad is connected to ground) 40 +85 C (Exposed pad is open) 48-pin QFN (0.5mm pitch) AKD4458 Evaluation Board for AK4458 AK4458VN (DIGITAL : U1053) Block diagram Pin Configurations CLOCK BUFFER CONTROL SIGNAL GENER ATOR COMMAND DECODER COLUMN DECODER...
[AK4458] FUNCTIONAL BLOCK DIAGRAM No. Pin Name I/O Function PD State 4. Block Diagram and Functions CAD0_I2C Chip Address 0 Pin in I2C Bus serial control mode Chip Select Pin in 3-wire serial control mode LDOE TVDD VDD18 DVSS AVDD AVSS Hi-Z Audio Data Format Select in Parallel control mode.
Page 55
G Bipolar Technology G Package Outline DIP16,DMP16 I PIN CONFIGURATION and BLOCK DIAGRAM NJU72343 (AV : U5202) NJM2595MTE1 (AV : U5206 Vin1 Vin2 75Ω Vout1 Driver Vin3 Pin Function 75Ω Vout2 No. Symbol Function No. Symbol Function Vin4 Driver AREF Analog reference potential terminal DATA IC control data input...
Page 57
MECHANICAL DISASSEMBLY Flowchart 1. WiFi ANT 2. FRONT PANEL ASSY 3. RADIATOR ASSY 4. DIGITAL PCB 5. SPK PCB 6. TRANS 7. SMPS PCB 8. REG PCB 9. AV PCB EXPLODED VIEW PACKING VIEW...
Page 58
DISASSEMBLY Flowchart • Remove each part following the flow below. • Reassemble the removed parts in the reverse order. • Read "SAFETY PRECAUTIONS" before reassembling the removed parts. • If wire bundles are removed or moved during adjustment or part replacement, reshape the wires after completing the work. Failure to shape the wires correctly may cause problems such as noise. •...
• The photographs with no shooting direction indicated were taken from the top of the unit. (1) Remove the screws. • Photos of NR1508 U are used in this manual. The viewpoint of each photograph (Shooting direction : X) [View from the top] ↓Shooting direction: B↓...
3. RADIATOR ASSY 4. DIGITAL PCB Proceeding : TOP COVER → RADIATOR ASSY Proceeding : TOP COVER → WiFi ANT → DIGITAL PCB (1) Remove the screws. (1) Remove the screws. ↓Shooting direction: D↓ ↓Shooting direction: C↓ View from the bottom ↑Shooting direction: A↑...
Page 61
5. SPK PCB 6. TRANS Proceeding : TOP COVER → WiFi ANT → DIGITAL PCB → SPK PCB Proceeding : TOP COVER → WiFi ANT → DIGITAL PCB → TRANS (1) Remove the screws. (1) Remove the CORD HOLDERs and connector wires. from CP4401 from CP4607 ↑Shooting direction: A↑...
PACKING VIEW Parts List http://dmedia.dmglobal.com/Document/DocumentDetails/23156 17 NR1608 Only N R 16 *MANUAL POLYBAG ASSY* *MIC ASSY* POLYBAG CODE: 6337-04006-201-0S POLYBAG CODE: 6330-21071-900-0S POLYBAG CODE: 4148-21019-000-0S ZIPPERBAG(A4size) ZIPPERBAG(A5size) SETUP MIC STAND SIZE : 350mm x 210mm SPOTIFY insertion sheet This part together with document and zipper bag are supplide. Notes on RADIO (ALL) INST.
REPAIR INFORMATION TROUBLE SHOOTING SPECIAL MODE 1. POWER Special mode setting button 2. Analog video 1. Version Display Mode 3. HDMI/DVI 2. PANEL / REMOTE LOCK Selection Mode 4. AUDIO 3-1. Selecting the Mode for Service-related 5. Network / Bluetooth / USB 3-2.
Page 65
TROUBLE SHOOTING 1. POWER 1.1. The unit does not power on 1.2. Fuse is blown The unit does not power on Blown fuse Check for short circuits between the Does the power indicator on the front panel flash Check the rectifier diode in the Does the power shut down after several seconds? Check for leaks and short circuits regulator output terminal and GND...
Page 67
3.1. No picture or sound is output (HDMI to HDMI) No picture or sound is output. (8) When using a MARANTZ Blu-ray/DVD player, is the "HDMI" indicator of the fluorescent display lit? Proceed to YES when using a Blu-ray/DVD player produced by other manufactures.
Page 68
(15) Are a picture and sound output when a differ- The TV is faulty. ent TV is used? Check the unit. "HDMI "Rx/Tx" Failure Detection"...
4. AUDIO 4.1. AUDIO CHECK No audio output CHECK 1 INPUT SURROUND MODE SOURCE Check the ANALOG AUDIO BLOCK Audio output OK? ANALOG 2CH DIRECT ANALOG CHECK 2 INPUT SURROUND MODE SOURCE Check the DIGITAL AUDIO BLOCK Legacy Audio output OK? COAX or OPT (PCM or DolbyDigital or dts…) CHECK 3...
4.2. Power AMP (AMP PCB) 4.3. Analog audio When using the protection pass mode, do not connect speakers to the speaker terminals. No audio output. No audio output. Protection is activated. Is a voltage of ± 8 V supplied to AV PCB [CP5201]? Repair the ±...
Page 71
5. Network / Bluetooth / USB 5.1. Cannot connect to the network Check the connection environment The circuit of NET5V POWER Insert the LAN cable correctly and then turn on Can the output voltage (5V) to Is NET5V POWER [U1013 : 40pin Is the LAN cable correctly inserted? between [U1013-Q1086 : FET- the power again.
Page 72
5.2. Cannot establish a Bluetooth connection Check the Bluetooth device being used Are the versions of the HEOS Version displayed in The Network Module software is faulty. Version Check Mode? Is the Bluetooth device compatible with the A2DP Use a device that is A2DP profile compatible. profile? The circuit of Network Module is faulty.
Page 73
5.3. Cannot recognize the connected USB device 5.4. No picture or sound is output Check the USB device being used Checking the unit (If no picture is output) Are digital video signals(LEGOPCK, LEGOVS, The circuit around Network Module, [U1024 : Is a USB hub being used? Do not use a USB hub.
Page 75
6. SMPS Operation waveform for each part DC 5V is not output. After primary side rectification Primary drain (Caution: High voltage, electric shock) (Caution: High voltage, electric shock) C4148 OPTION OPTION CT714eV5V103M250VacB OPTION_2 Replace the [U4140 : TOP268VG D4142 1N4007S Is [U4140 : TOP268VG] dam- ZD4151 and D4142 / D4143 / D4144 /...
Page 76
HDMI "Rx/Tx" Failure Detection 1. Prior checking Check item(0). : Checking the HDMI connector Checking the condition of the HDMI pin (rear/front). There are deformed pins. Replace the HDMI connector. Check for deformed pins. None of the pins are deformed. Check by following the flow chart for "3.
Page 77
Parity: none Transmitted text Flow control: none Select Append CR-LF Forward: (none) S706-709 : No Prefernce S702 : 3.3V Check the Local Echo check box. RS-232C Cable WRITING KIT Figure 1 Device Connection Method (NR1508) Figure 3 Serial Port Setup Screen...
After exiting "Setup Assistant" execute the above. 1. Input a command in the Press 2.Click on the transmission button. transmission command input. Figure 6-1. AVR settings (NR1508) All the for Volume 7 segment indicator Lights Figure 8 Method for Sending Termite Commands...
3. Starting detecting the point of failure Check item(1). (2-2) Display when an Error is not detected. Check the power supply status and communication status with the CPU of each device. Start in HDMI Diagnostics mode and follow the procedures below. 1 Auto Test Cancel the mode, and proceed to check item...
Page 80
Check item(2). : Check operation of the HDMI input terminal. Check item(3). : Check operation of the HDMI output terminal. Go to check item (52) (OSD[ADV7623] failure detection When the HDMI input terminal of this device is connected to the player correctly, is sound heard from procedure) the speaker? ※...
Page 81
3-1. Error Code H1-01 failure detection procedure Checking device. (HDMI Rx/Tx) Check the power supply voltage. (HDMI Rx/Tx) Checking the reset waveform. (HDMI Rx/Tx) Check item(5). Check the power supply voltage. : Check item(7). Checking the reset waveform : Check the waveform. Does the power supply voltage of the HDMI Rx/Tx [U1027] indicate the correct voltage (1.1V, 3.3V)? When the power is turned on, is the TP waveform correct (as The test points are as follows.
Page 82
Check the I2C communication line. (HDMI Rx/TX) Check item(8). Check the I2C communication line : Check the waveform. Is the "I2C" waveform of the TP HDMI Rx/Tx [U1027] correct (like the one shown in the diagram) when the power is turned P_DA 116pin P_CK 114pin U1027...
Page 83
3-2. Error Code H1-02 failure detection procedure Checking device. (HDMI SW) Checking the reset waveform. (HDMI SW) Check item(10). Checking the reset waveform : Check the waveform. When the power is turned on, is the TP waveform correct (as shown in the figure)? Examples of confirmation waveform 115 pin Voltage scale:1.0V/div...
Page 84
3-3. Error Code H1-07 failure detection procedure Checking device. (OSD) Check the power supply voltage. Checking the reset waveform. Check item(14). Checking the reset : Check item(12). Check the power supply voltage. Check item(13). Check the power supply voltage. Check the CPU. Does the power supply voltage of the Check the power supply components [U1067,...
Page 85
Check the I2C communication line. Check item(15). Check the I2C communication line : Check the CPU. Is the "I2C" waveform of the HDMI OSD [U1030] correct (like the one shown in the diagram) when the power is turned on? HSCL HSDA U1030 *The diagram shows an example.
Page 86
3-4. Error Code H1-15 failure detection procedure Checking device. [U1029 : MX25L3206EMI(E3, E1C, K)/MX25L6406EMI(E2)] Check item(17). Write to the OSD ROM. Recheck from check item (1). Does Error Code H1-15 continue? Check item(18). Replace [U1029] with a new device. Recheck from check item (1).
Page 87
3-5. Error Code H1-08 failure detection procedure Checking device. [U1021 : ADSP21487] Check the power supply voltage. Checking the reset waveform. Check item(19). Check the power supply voltage. Check item(20). Check the power supply voltage. Check item(21). Checking the reset : Check the CPU.
Page 88
Check the SPI communication line. Check item(22). Check the SPI communication line : Check the CPU. Is the "SPI" waveform of the TP near the DSP [U1021] correct (like the one shown in the diagram) when the power is turned on? D_CK 3pin D_MOSI 4pin D_CS 6pin...
Page 89
3-6. Error Code H1-12 failure detection procedure Checking device. [U1040 : PCM9211] Check the power supply voltage. Checking the reset waveform. Check item(24). Check the power supply voltage. Check item(25). Check the power supply voltage. Check item(26). Checking the reset : Check the CPU.
Page 90
Check the communication line. Check item(27). Check the communication line : Check the CPU. Is the waveform of the TP near the DIR [U1040] correct (like the one shown in the diagram) when the power is turned on? DR_CK 25pin DR_DIN 24pin DR_CE 26pin DR_DOUT 23pin...
Page 91
3-7. HDMI Rx/Tx [MN864788] failure detection procedure Checking operation between the HDMI (Rx/Tx) device and the player Check item(30). Checking the +5V/DDC status register : Example Send the following command from Termite.exe. b In order to check, connect the player to the HDMI terminal and configure the player as AVR source. Check the sound output while turning on the player.
Page 92
When the results of check item (29) are "00" When the results of check item (30) are "00 or 04" (Detection of 5V is not OK) (Detection of DDC is not OK.) Check the +5V voltage. (HDMI Rx/TX) Check the DDC line. (HDMI Rx/Tx) Check item(31).
Page 93
When the results of check item (30) are "22" (Detection of DDC is OK.) Checking the TMDS status register. 3.3V TMDS Signal TMDS Check item(33). Checking register of the TMDS CLK detection status Example register : Example of waveform in check ① Example of waveform in check ② Send the following command from Termite.exe.
Page 94
3-8. HDMI SW [MN864787] failure detection procedure Checking operation between the HDMI (HDMI SW) device and the player HDMI IN Check item(37). Checking the DDC status register : Example Send the following command from Termite.exe. Case of HDMI IN1 b In order to check, connect the player to the HDMI terminal and configure the player as AVR source. Send the command "i 002B 0084 0001".
Page 95
When the results of check item (36) are "00" When the results of check item (37) are "00 or 04" (Detection of 5V is not OK) (Detection of DDC is not OK.) Check the +5V voltage. (HDMI SW) Check the DDC line. (HDMI SW) Check item(38).
Page 96
When the results of check item (37) are "22" (Detection of DDC is OK.) Checking the TMDS status register (HDMI SW) 3.3V TMDS Signal TMDS Check item(40). Checking register of the TMDS CLK detection status Example register : Example of waveform in check ① Example of waveform in check ② Send the following command from Termite.exe.
Page 97
3-9. Front HDMI Buffer IC [AD8195] failure detection procedure Checking operation between the HDMI (Front HDMI Buffer) and the player Checking the +5V/DDC status register (Front HDMI Buffer) Check item(46). Checking the 5V status of the register : Example Send the following command from Termite.exe. b In order to check, connect the player to the HDMI terminal and configure the player as AVR source.
Page 98
When the results of check item (46) are "00" When the results of check item (47) are "00 or 04" (Detection of 5V is not OK.) (If the DDC are not OK) Check the +5V voltage. (Front HDMI Buffer) Check the DDC Line. (Front HDMI Buffer) less than 100KHz Check item(48).
Page 99
When the results of check item (47) are "22" (Detection of DDC is OK) Checking the TMDS status register 3.3V TMDS Signal Check item(50). Check the TMDS CLK detection status of the regis- Check item (51). Checking the TMDS input waveform. : Example ter.
Page 100
3-10. OSD [ADV7623] failure detection procedure Checking the TMDS status register (OSD -> HDMI Rx/Tx) 3.3V TMDS Signal Check item(52). Check the TMDS CLK detection status of the regis- Check item (53). Checking the TMDS input waveform. : Example ter. Check the TMDS waveform at the following test point.
Page 101
Check the connection between the HDMI OUT terminal and the TV. Connect the HDMI OUT terminal and the TV, and then turn on the TV and check the following items. Checking the HPD/RXSENSE status register. (HDMI TX -> Monitor) Check item(54). Check the HPD and RXSENSE register value of the Example HDMI TX device.
Page 102
When the results of check item (54) are "30" (Detection of HPD is OK / Detection of RXSENSE is OK ) Example Checking the EDID register. (Monitor) Check item(55). Check the Monitor EDID : ① Unplug the AC cord. Plug the AC cord into a power outlet. ②...
Page 103
When the results of check item (54) are "10" When the results of check item (54) are "20" (Detection of HPD is OK / Detection of RXSENSE is not OK ) (Detection of HPD is not OK / Detection of RXSENSE is OK ) Check the RXSENSE.
Page 104
When the results of check item (54) are "00" (Detection of HPD is not OK / Detection of RXSENSE is not OK ) Check the RXSENSE/HPD. (Monitor) Check item(60). Checking the HPD and RXSENSE. : Does the test point of RXSENSE close to the HDMI output terminal [N1018] indicate the (3.3V)? Does the voltage of HPD test point close to the HDMI output terminal [N1018] indicate "Hi"...
Page 105
3-11. Fault detection procedure between HDMI Rx/Tx [MN864788] & OSD [ADV7623]. HDMI IN1 HDMI OUT ※ In order to check, connect the player to the HDMI terminal and configure the player and TV as AVR source. Check the sound output while turning on the player and TV. Checking the TMDS status register (Rx/Tx ->...
SPECIAL MODE Special mode setting button b No. 1 - 4, 6 - 8 : While holding down buttons "A", "B" and "C" simultaneously, press the power button to turn on the power. b No. 5, 9 : While the power is on, hold down buttons "A" and "B" for at least 3 seconds . Mode Button A Button B Button C Descriptions...
Page 109
Q3 HEOS Config : Q7 Bluetooth MAC Address : q Model destination information : y DSP ROM : HEOS Config *BT MAC Address NR1508 \ :**.** "Press "STATUS" button. "Press "STATUS" button. \ : Region (U, N, K, F) Production...
1.4. Error display See the table below for descriptions of the displayed errors and countermeasures for these. If multiple errors occur, only one item is displayed. The priority order is w, e, r, q. Condition States Display TROUBLE SHOOTING FIRM ERROR The model name, brand name and region information written in the firmware are compared to the region settings in the PCB.
Page 111
1.5. Version Display in the Setup Menu Follow the steps below to display the firmware information. (1) Press the "SETUP" button on the remote control. (2) Select "General - Information - Firmware". The version information is displayed as a 16-digit number as shown in the screenshot below. General/Firmware Version XXXX-XXXX-XXXX-XXXX...
Page 112
2. PANEL / REMOTE LOCK Selection Mode 2.1. Actions Switch the PANEL LOCK and REMOTE LOCK modes between on and off. 2.2. Starting up While holding down buttons "M-DAX" and "DIMMER" simultaneously, press the power button to turn on the power. Select the desired mode using the "TUNER PRESET CH+"...
3-1. Selecting the Mode for Service-related 3-1.1. Actions Select diagnostic mode (service path check mode), protection history display mode, or Operation Info 4.OP INFO mode or TUNER STEP mode. Operation Info for the unit can be checked. 3-1.2. Starting up While holding down buttons "TUNER PRESET CH+"...
3-2. Protection History Display Mode 3-2.1. Actions (c) DC (if the last protection is DC) This mode enables the unit to record and display the event when the THERMAL, ASO or DC protection is PRT:DC activated. Cause : DC output of the power amplifier is abnormal. If protections have been activated multiple times, the latest protection operation is recorded.
Page 115
3-2.4. Clearing the Protection History There are two ways to clear the protection history. (a) Activate Protection History Display Mode. Press the "STATUS" button to display the protection his- tory. Press and hold the "DIMMER" button for 3 seconds. PRT:DC Press and hold the "DIMMER"...
Page 116
3-3. Operation Info Mode 3-4. TUNER STEP mode (U / N only) 3-3.1. Actions 3-4.1. Actions This mode enables the unit to display the accumulated operating time, power On count and each pro- This is a special mode for enabling reception STEP of the ANALOG TUNER to be changed. tection count.
4. Protection Pass Mode 5. Network Initialization Mode 4.1. Actions 5.1. Actions • This mode allows the power to be turned on without activating protections. The following items are initialized. • This mode functions in the same way as normal power-on, except that protections are not activated. Network setup •...
6. Clearing the Operation Info 6.1. Actions • Displays the accumulated operating time of the unit, the number of times the power was switched on, and the number of occurrences of each protection. 6.2. Operations Remove all input/output terminals and the AC plug. Connect the AC plug again and place the product in standby mode.
Page 119
DIAGNOSTIC MODE Service Path Check Mode 1.1. Actions This function is convenient for confirming problem paths in the product and checking the paths after repairing. The Video and Audio paths can be checked. The backup data is not rewritten. 1.2. Starting up While holding down buttons "TUNER PRESET CH+"...
Page 120
1.6. Confirmation items for the video system See the block diagram fig.XXth. Paths to be confirmed Display Settings What to confirm Input Source : CBL/SAT ・ CVBS input ⇒ CVBS output Video Conversion (IP Scaler) : OFF, All sources ( b The input source can be switched to any source except CBL/SAT.) 1 Analog Video pass fig.05 V01:VIDEO PASS...
JIG FOR SERVICING Use the following jigs (extension cable kit) when repairing the PCBs. (3) Remove the DIGITAL PCB from the chassis and turn it over. Order with your dealer for the jigs your dealer if necessary. Place an insulation sheet larger than the PCB underneath the DIGITAL PCB. b Connect the earth of the PCB to the chassis using an earth wire, etc.
ADJUSTMENT Adjusting Idling Current 1. Preparation (1) Prepare a DC voltmeter. (2) Place the unit under normal usage conditions, away from highly ventilated areas such as next to an air conditioning machine or electric fan. AMP UNIT The set requires an ambient temperature of 15℃ to 30℃ and standard humidity. DC Voltmeter (3) Settings of This Unit •...
Page 137
UPDATING PROCEDURE AFTER REPLACING THE PCB. PROCEDURE AFTER REPLACING THE U-COM, ETC. FIRMWARE UPDATE PROCEDURE 1. Items necessary for update 2. Updating via USB 3. Update method when the DIGITAL PCB or network module is replaced (Using a USB flash drive) 4.
Page 138
A : The software has been written. The software is not written at the time of replacement. N1001 R2002 R2111 R1999 D5.2V U1008 R1113 DGND C1752 DGND R1136 R1115 R1105 NR1508 HDMI [MP] C1786 C1218 R1137 X1901 U1007 C1219 22.5792MHz R1326 C1780 R2013 L1014 LEGO5V C1751...
Update download file when the firmware is updated (Two files, "HW component" and "LEGO component") Download from SDI Model Name Model Area For HW component For LEGO component NR1508 U North America (U) Product ID : 100100550100 DPMS_NR1508U_LEGO_xxxx.zip NR1508 N Europe (N) Product ID : 100100550200 DPMS_NR1508N_LEGO_xxxx.zip...
2. Updating via USB The latest firmware can be downloaded to a USB memory for updates. 2.1. Connecting to the USB Memory (1) Preparation • Use a memory that supports USB2.0. • USB format : Prepare a USB memory formatted in FAT16 or FAT32. •...
Page 141
3. Update method when the DIGITAL PCB or network module is replaced (Using a USB flash drive) 3.1. File structure on USB flash drive (5) USB Update starts automatically. The Standby LED lights red. DIGITAL PCB or network module is replaced onto the USB flash drive in the following structure. Display during USB update After unzipping the files, store them in the root of the same USB flash drive.
Page 142
4. Update Method for Service Region Settings Copy the Service Region Settings from the USB flash drive to this unit. (5) Copy the files created on the USB flash drive. 4.1. Creating a Service Region Settings file (1) Click [Start button] - [Accessories] - [notepad] on the PC to launch the notepad. copy to USB flash drive (2) Enter "TEXT".
Page 143
5. Normal Firmware Update Method from USB Flash Drive 5.1. File structure on USB flash drive (4) Insert the USB flash drive into the USB port. Copy the normal update files onto the USB flash drive in the following structure. Download firmware After unzipping the HW component USB update files for the target model and LEGO USB update files, in USB flash drive.
6. Normal Firmware Update Method from OTA 6.2. Check and update the firmware Download the latest firmware from our website and update the firmware. 6.1. Network Connection Check if there is a firmware update available. It is also possible to check approximately how long the (1) System Requirements update will take.
Page 145
Update ErrorYYXX : DeviceID, : ErrorCode) Update ErrorYYXX DSP2 ↓↑ The display is alternately displayed. b Except : NR1508/NR1608/SR5012 DSP3 Please check you b Except : NR1508/NR1608/SR5012 Content of the display is scrolled. DSP4 b Except : NR1508/NR1608/SR5012 Audio PLD...