Table of Contents
Related Manuals for Skye SKP 220V
Summary of Contents for Skye SKP 220V
- Page 1 1 Channel External Voltage Amplifier SKP 220V Skye Instruments Ltd., 21 Ddole Enterprise Park, Llandrindod Wells, Powys LD1 6DF UK Tel: +44 (0) 1597 824811 skyemail@skyeinstruments.com www.skyeinstruments.com Doc No. 485...
- Page 2 Skye Instruments Ltd. Skye Instruments is based in the UK and we are very proud to be celebrating being in business since 1983. Our products are designed and built in the UK. We have a very wide product base and our sensors &...
-
Page 3: Table Of Contents
CONTENTS Page Introduction ..............1 Wiring & Power Details ............ 2 2.1 Wiring ............... 2 2.2 Connecting a Sensor ........... 2 2.3 Sensor Output & Power Supply ........3 2.4 Connecting to Terminal ..........4 Housing.... -
Page 4: Introduction
Thank you for purchasing a Skye Instruments External 1-Channel Voltage Amplifier. This amplifier's function is to transform the current from one of Skye Instruments' unamplified sensors into a voltage output, scaled over a desired range pre-determined at the time of ordering (e.g. 0 – 2V, 0 – 5V, etc.). -
Page 5: Wiring & Power Details
2. WIRING & POWER DETAILS 2.1 Wiring The wires should be connected to the terminal blocks in the following way: Terminal No. Function Wire Colour Sensor -ve current output Blue Sensor +ve current output Green Power supply +ve Amplified voltage output -ve Green Amplified voltage output +ve Yellow... -
Page 6: Sensor Output & Power Supply
2.3 Sensor Output & Power Supply The following table shows the typical outputs of Skye amplifiers, along with the power supply required for each. Sensor Output: Power Supply Required: Up to 0–2 V 5-15 V DC Up to 0–5 V 9-15 V DC Up to 0–10 V... -
Page 7: Connecting To Terminal
2.4 Connecting to the Terminal Please also ensure that on replacing the lid that the wires or silica gel pack do not get trapped in the sealing lip. Connecting wire ends to the terminal is intended to be easy. Above each terminal block there is an opening and a metal clip inside. -
Page 8: Housing
3. HOUSING The enclosure is made from light grey ABS (UV stabilised). Two grey nylon cable glands are fitted for cable entry. It is considered to be protected from ingress to IP65. On no account should it be subjected to immersion. Dimensions of the amplifier unit are approx.: 80mm x 58mm x 121mm (DxHxW), this includes the cable glands and feet. -
Page 9: Specifications
Requirements NOTES ON SPECIFICATIONS (1) All Skye sensors will work at levels of irradiance well above that found in terrestrial sunlight conditions, room or growth chamber lighting. These are default working ranges, check individual calibration certificate. (2) Maximum change in one year. Calibration check recommended at least every two years. Experience has shown that changes are typically much less than figures quoted. -
Page 10: Troubleshooting
5. TROUBLESHOOTING If you have any problems with using the external amplifier unit, please refer to this section. If you still have queries, do not hesitate to contact us via e-mail at: skyemail@skyeinstruments.com or by telephone on +44(0)1597 824 811. My sensors are not reading what I expect / I'm getting odd readings. - Page 11 Skye Instruments Ltd., 21 Ddole Enterprise Park, Llandrindod Wells, Powys LD1 6DF UK Tel: +44 (0) 1597 824811 skyemail@skyeinstruments.com www.skyeinstruments.com...
Need help?
Do you have a question about the SKP 220V and is the answer not in the manual?
Questions and answers